Wingsland R6 User manual

⑥ Photo/Video
⑤ Antenna
Shutter for taking
p h o t o s / v i d e o s .
Tr ans mit fli gh t control s i g n a l
a n d Wi-F i l i v e-v i e w s i gn a l .
⑦ USB Port
Powering the remote controller.
⑧ One-key Takeoff/Landing
Co mm an d t h e a ir cr af t a u t o
ta ke off /l an di ng .
Overview
Charging the Battery
Diagram
R6 is a portable and practical remote controller with folding design and
extended mobile device holder. The top standard joysticks andergonomic
handle design will make your remote precise and mastered.R6 remote
controller equips a capacity of 1700 mAh Li-Po battery and max operating
time is 90 minutes.
1
2
3
4
① Left /Right Joystick
② Battery Indicator
Real-time battery level indicating.
③ Wi-Fi Indicator
Real-time Wi-Fi signal level indicating.
④ Handle
Ex tend ed gr ip for mount ing
mob ile de vice s.
5
6
7
8
The default control mode is Mode 2.
Mode 1 and Mode 2 can be switched
under general setting in WINGSLAND
FLY APP.
(right button)
A fully charging takes around 120 minutes.
Folded Up
Extended
⑨ Reset Button
Press this button and hold for 3 seconds
with a tool. Reset the Wi-Fi name and
password of remote controller.
9
Power the remote controller by using the Micro-USB and connect to a
suitable power source. Ensure that the Remote controller is power off
when charging. The indicator which located in the leftmost will light on
as the remote controller is charging. The remote controller is fully
charged when this indicator turn off. Then detach the Micro-USB cable
from the port.

Optimal Transmission Range
The transmission signal between the aircraft and the remote controller is most
reliable within the area that depicted below:
Operation
Power On/Off
Power off
Mounting your Mobile Device
After unfold two holder arms out, extend the holder grips and adjust the
position. Place and make sure the entire mobile device is seatedin the mobile
device holder.
Battery Indicator
Power on
Make sure the mobile device is installed firmly.
Power off: Fold one or two holder arms to powering off the remote controller.
Power on: Unfold two holder arms out to 90 degrees to powering on the
remote controller.
Indicator Current Battery Level
Please Recharge the Battery
High Battery Level
Fully Charged
12
Attention to Battery Level

Connecting your Aircraft
Takeoff/Landing
Photo/Video
Photo：Click the right button once to take one photo. A successful
prompt will be displayed in WINGSLAND FLY flying interface. The
burst mode can be set in the app for taking 6 photos at once.
The best working range
Weak signal Strong signal
Takeoff altitude: Indoor 1.2m, Outdoor 2.5m.
Connecting mobile device Connecting aircraft
Takeoff :Hold the left button for 3 seconds to active the feature.
The aircraft will automatically hover up and stabilize.
Setting
Confirm
Choose ai rc ra ft please
Choose aircraft
Enter the p as sw ord
3
Landing: Hold the left button for 3 seconds, the aircraft will auto-
matically perform the landing. Check the landing area condition
and make sure no obstacle under the aircraft.
R6 remote controller support a wide range of WINGSLAND aircraft such
as S6、M5.Please follow the steps below to use the remote controller：
1. Power on the R6. Select and connect the R6 Wi-Fi in your mobile device
Wi-Fi l ist. The de fau lt Wi-Fi name is “ wingslandR6_rc_xx xxxx” and the
password is “wingsland”. Run the app when the Wi-Fi is linked up, then tap
“GO Start to Fly” to enter the main flying interface.
2. In the general setting, type in the aircraft Wi-Fi name and the password.
Then power on the air craft, the re mot e and the a ircraft will be l inked up
automatically.
3. After the pairing, the aircraft can be only controlled by the remote controller.
Ot her fea t ur e s ca n st ill be a cti v e an d se t in the app exc ept the vir t ua l
joystick control function.

Video：Double-click the right button to start taking a video. Double-click
the right button again to complete a video taking.
Connect the Remote Controller
Perform the following steps for connect the R6 and your a i rcra ft:
1. Power on the R6 first, then power on the aircraft.
Battery Usage Safety Notice:
Certificate
Specifications
3. A blue solid LED indicates the connection is successful.
● Do not put the battery into fire or store in a high temperature environ ment.
● Always use a WINGSLAND approved adapter. Keep the battery
awayfrom inflammable during the charging.
● Do not drops, strike, impale battery. Do not manually short-circuit the
battery. Do not store the battery with conductors.
● Do not drops, strike, impale battery. Do not use a swollen, leaky or
damaged battery.
● The battery performance will be affected after long time storage at a
low battery level.
● Store the battery in a dry environment with an appropriate room
temperature.
● If found the battery leakage, do not contact with skins and eyes. If you
do contact, immediately rinse with plenty of water and seek medical
help.
● The battery level will be affected when using in a low temperature or a
high temperature.
● To avoid fire, serious injury, and property damage, observes the safety
guidelines and user manual when using, charging, or storing your
batteries.
Live-View：2.4GHz(Digital)，Remote：5.8GHz
FCC：≤26 dBm CE：≤20 dBm
Folded：165*58*70mm
Unfolded：165*152*70mm
Minimum：130*60*9mm
Maximum：165 * 84 * 9mm
220g
1700mAh
≈90 minutes
10℃-45℃
1.2A @ 4.2V
Micro USB
Operating Frequency
Transmitter Power(EIRP)
Weight
Battery Capacity
Operating Time
Operating Temperature
Battery Voltage
Port
Dimensions
Adapted Mobile Device Size
2. Hold the two buttons on the R6 at same time for 3 seconds, when the
Wi-Fi indicator is blinking shows the R6 is connecting to the aircraft.

★Any change of this Guide will without prior notice.Please download the latest
version of "R6 User Manual" from official website(www.wingsland.com)