Winmate R15IH3S-67A3HB User manual

Please read these instructions carefully before using this product, and save this manual for future use.
15” G-WIN Rugged
Full IP67 Panel PC
R15IH3S-67A3(HB)
R15IB3S-67A3(HB)
R15ID3S-67A3(HB
Quick Start Guide
V1.0
For more information on this and
other Winmate products, please
visit our website at:
www.winmate.com
Document Part Number: 9152111I102C

- 2 -
CONTENTS
1 INTRODUCTION - 6 -
1.1 Features - 6 -
1.2 Package Contents - 7 -
1.3 Description of Parts - 9 -
1.4 Physical Buttons and LED Indicators - 10 -
2 GETTING STARTED - 12 -
2.1 Turning on Your Device - 12 -
2.2 How to Enable Watchdog - 13 -
2.3 Turning off Your Device - 15 -
3 Mounting - 16 -
3.1 VESA Mounting - 16 -
3.2 Dash/ Yoke Mounting - 17 -
4 INSTALLATION - 19 -
4.1 Wiring Requirements - 19 -
4.2 Connecting to Other Devices - 20 -
4.3 Connector Description - 21 -
4.3.1 Power Input Connector - 21 -
4.3.2 Ethernet Connector - 22 -
4.3.3 Serial Interface Connector - 23 -
4.3.4 USB 2.0 Connector - 24 -
5 SPECIFICATIONS - 25 -
APPENDIX - 27 -
Appendix A: Cleaning the Monitor - 27 -
Appendix B: Winmate Software Development Kit - 28 -

- 3 -
FCC Statement
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received
including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a
class "B" digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at him own expense.
European Union
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010/ A1: 2015
oIEC61000-4-2: 2009
oIEC61000-4-3: 2006+A1: 2007+A2: 2010
oIEC61000-4-4: 2012
oIEC61000-4-5: 2014
oIEC61000-4-6: 2014
oIEC61000-4-8: 2010
oIEC61000-4-11: 2004
EN55032: 2012/AC:2013
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/
A2:2013
This equipment is in conformity with the requirement of the following EU
legislations and harmonized standards. Product also complies with the
Council directions.

- 4 -
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in
any form or by any means, electronic or mechanical, for any purpose, without the
prior written permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their
respective owners.
Disclaimer
Winmate Inc. reserve the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order
to improve design and/or performance. We assume no responsibility or liability for
the use of the described product(s) conveys no license or title under any patent,
copyright, or masks work rights to these products, and make no representations
or warranties that these products are free from patent, copyright, or mask work
right infringement, unless otherwise specified. Applications that are described in
this manual are for illustration purposes only. We make no representation or
guarantee that such application will be suitable for the specified use without
further testing or modification.
Warranty
Winmate Inc. warranty guarantees that each of its products will be free from
material and workmanship defects for a period of one year from the invoice date.
If the customer discovers a defect, we will, at his/her option, repair or replace the
defective product at no charge to the customer, provide it is returned during the
warranty period of one year, with transportation charges prepaid. The returned
product must be properly packaged in its original packaging to obtain warranty
service. If the serial number and the product shipping data differ by over 30 days,
the in-warranty service will be made according to the shipping date. In the serial
numbers the third and fourth two digits give the year of manufacture, and the fifth
digit means the month (e. g., with A for October, B for November and C for
December).
For example, the serial number 1W14Axxxxxxxx means October of year 2014.
Customer Service
We provide a service guide for any problem by the following steps: First, visit the
website of our distributor to find the update information about the product.
Second, contact with your distributor, sales representative, or our customer
service center for technical support if you need additional assistance.
You may need the following information ready before you call:
Product serial number
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business
day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.

- 5 -
Safety Information
WARNING! / AVERTISSEMENT!
Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections
while the power is on. Sensitive electronic components can be
damaged by sudden power surges. Only experienced electronics
personnel should open the PC chassis.
Toujours débrancher le cordon d’alimentation du chassis lorsque
vous travaillez sur celui-ci. Ne pas brancher de connections
lorsque l’alimentation est présente. Des composantes
électroniques sensibles peuvent être endommagées par des sauts
d’alimentation. Seulement du personnel expérimenté devrait ouvrir
ces chassis.
CAUTION/ATTENTION
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution, use a
grounding wrist strap at all times. Place all electronic components
in a static-dissipative surface or static-shielded bag when they are
not in the chassis.
Toujours verifier votre mise à la terre afin d’éliminer toute charge
statique avant de toucher la carte CPU. Les équipements
électroniques moderns sont très sensibles aux décharges
d’électricité statique. Toujours utiliser un bracelet de mise à la
terre comme précaution. Placer toutes les composantes
électroniques sur une surface conçue pour dissiper les charge, ou
dans un sac anti-statique lorsqu’elles ne sont pas dans le chassis.

- 6 -
1 INTRODUCTION
Congratulations on purchasing Winmate® G-WIN Rugged Full IP67 Panel PC.
Panel PC features 15” panel with sunlight readable screen, fanless cooling
system, low power consumption, WLAN integration, great ability for anti-shock &
vibration. The robust design fits the demands for every harsh environment
applications such as logistics, transportation/ fleet management, heavy vehicles,
utility and also outdoor usage.
1.1 Features
Winmate® 15” G-WIN Full IP67 Panel PC features:
High Quality 15" Panel, 1024 x 768 resolution, 400 nits
IP67 Dust/ Water proof design (with VESA mounting)
Aluminum die-casting housing with anti-corrosion treatments
Build-in ambient light sensor
Wide range 9 to 36V DC input with isolation
Optional 6-60V DC Input, and Optional for Ignition On/Off delay
5 Wire resistive touch/ anti-reflective protection glass (optional)
Optional HB/ Sunlight readable with brightness up to 1000 nits

- 7 -
1.2 Package Contents
Carefully remove the box and unpack your device. Please check if all the items
listed below are inside your package. If any of these items are missing or
damaged contact us immediately.
Standard factory shipment list:
Panel PC
Quick Start Guide
(Hardcopy)
Driver CD & SBC User
Manual
Varies by product
specifications
9152111I102C
IH32: 9171111I102S
IB32: 9171111I103I
ID32: 9171111I101M
Power Cable
Serial Interface Cable
LAN Cable
94J003L020K1
94G0103090Q0
94I0080080KF
USB Cable
9480108080Q0

- 8 -
Your package may include optional accessories based on your order:
Mounting Bracket
99KK15A00001

- 9 -
1.3 Description of Parts
Unit: mm
Dimensions: 398 x 308 x 58
№
Description
№
Description
①
LAN (M25 Type)
④
9-36V DC (M25 Type)
②
USB (M25 Type)
⑤
OSD Control Panel
③
RS232 (M25 Type)

- 10 -
1.4 Physical Buttons and LED Indicators
Physical buttons and LED indicators (OSD Control Panel) located on the rear
side of the Panel PC.

- 11 -
Physical Buttons
Icon
Button
Function
Power
Turn ON or turn OFF the Panel PC.
Reset
Clear any pending errors or events and brings a
system to normal condition or an initial state.
Lock / Unlock
Tap this button to lock / unlock the function of
OSD panel.
Auto Dimming/
Manually
Tap the button once to AUTOMATICALLY adjust
brightness mode.
Press the button again to MANUALLY adjust
brightness mode.
Day/ Night Mode
Tap this button to enter DAY MODE.
Tap this button to enter NIGHT MODE to
increase visibility in low-light conditions.
Brightness UP
Increase the brightness of the display screen, or
allows user to navigate items of a single OSD
menu.
Brightness
DOWN
Decrease the brightness of the display screen, or
allows user to navigate items of a single OSD
menu.
LED Adjustment
Adjust the brightness of the LED.
LED Indicators
Indicator
Color
Definition
PWR
Green
Power is ON and the device functions normally.
Orange
Panel PC is suspended.
HDD
Green
HDD is active.
OFF
HDD is inactive.

- 12 -
2 GETTING STARTED
2.1 Turning on Your Device
1. Remove the protective cap of the power connector.
2. Connect power cable to the connector of your device. Make sure the cable
fits to the connector, then tighten the O-ring (by turning clockwise) to
secure the connection.
3. The device will boot automatically when powered on.

- 13 -
2.2 How to Enable Watchdog
To enable Watchdog, you need to download Winmate Watchdog utility. Find
more information on Watchdog in “Watchdog Guide” that you can download from
Winmate Download Center or File Share. Refer to the User Manual for more
details.
To enable watchdog in Watchdog AP follow the instructions below:
1. On the right bottom side of the desktop screen, click triangle button to
show hidden icons.
2. Click icon to open Watchdog utility.
3. In Watchdog utility window set countdown time and periodically feed time,
or disable watchdog.

- 14 -
Example:
Every 10 min watchdog will
monitor the system, in case any
error occurs the system will
restart automatically when the
countdown time reaches 0.
Every 9 min watchdog timer will
be reset to 10 min.
Settings
Description
Watchdog Countdown Time
The system automaticity restarts when this
countdown time reaches zero.
Default: 10 min
Periodically Feed Time
To set a cycle time to automatically reset
watchdog timer.
Default: 9 min
Enable / Disable
Enable or disable watchdog.
Default: Enable

- 15 -
2.3 Turning off Your Device
To shut down your device:
1. Select the Start button ( ) and then select Power > Shut down.
2. Disconnect the power cord from the Panel PC to completely turn off the
device.
To forcibly shut down your device, press and hold for three to five seconds the
power button located on the front OSD control panel.
IMPORTANT:
During forced shut down unsaved data may be lost.

- 16 -
3 Mounting
3.1 VESA Mounting
This device supports VESA Mounting and provides various types of mounting
options to fit any industrial use or vehicle.
Size
VESA Plate
15”
100x100 mm
Mounting Instruction
Use Philips M4x5 screws to fix the desk stand to VESA holes on the back cover
of the device.
*The picture is for demonstration purposes only. VESA Mounting accessories are
not supplied by Winmate.

- 17 -
3.2 Dash/ Yoke Mounting
You can purchase mounting bracket from Winmate as an optional accessory.
Part Number: 99KK15A00001
Mounting instruction:
1. Place the Panel PC on the bracket stand, aiming screw hole for each other.
2. Secure three M5x10 screws to fix the device upon the bracket stand.
3. Secure tightly locking handle to the Panel PC.

- 18 -
4. Loosen the hand-screw adjustment tool, then you can adjust product angle
on the stand. Then screw the product tightly again to secure the stand
position.
Desk Stand Dimensions

- 19 -
4 INSTALLATION
4.1 Wiring Requirements
The following common safety precautions should be observed before installing
any electronic device:
Strive to use separate, non-intersecting paths to route power and
networking wires. If power wiring and device wiring paths must cross make
sure the wires are perpendicular at the intersection point.
Keep the wires separated according to interface. The rule of thumb is that
wiring that shares similar electrical characteristics may be bundled
together.
Do not bundle input wiring with output wiring. Keep them separate.
When necessary, it is strongly advised that you label wiring to all devices
in the system.
CAUTION
Do not run signal or communication wiring and power wiring in the same
conduit. To avoid interference, wires with different signal characteristics
(i.e., different interfaces) should be routed separately.
Be sure to disconnect the power cord before installing and/or wiring your
device.
Verify the maximum possible current for each wire gauge, especially for
the power cords. Observe all electrical codes dictating the maximum
current allowable for each wire gauge.
If the current goes above the maximum ratings, the wiring could overheat,
causing serious damage to your equipment.
Be careful when handling the unit. When the unit is plugged in, the internal
components generate a lot of heat which may leave the outer casing too
hot to touch.

- 20 -
4.2 Connecting to Other Devices
This Panel PC comes with various interfaces located on the bottom panel. All of
these connectors have been shipped with protective caps. To ensure the
waterproof function can work properly, make sure that the protective caps and
have been securely tightened whenever the connectors are not used.
IMPORTANT
Please note that when reinstalling the protective cap, it must be fully tightened to
ensure the unit is properly sealed to meet the IP67 enclosure rating.