Winners Only DS54072 User manual

WINNERS ONLY
®
ASSEMBLY INSTRUCTIONS
PROD. NO: DS54072
Thank you for purchasing this quality product. Please read instructions thoroughly before unpacking
the assembly parts.
1 OF 3
Caution : Sharp exposed staple tips can cause injury, therefore for your protection, please remove any exposed
staples used in packing.
Please keep all hardware parts out of the reach of children.
1. We recommend that you should assemble this product with assistance of another person; this will
make the assembly easier, and will help to prevent personal injury and to insure parts are not damaged during
the assembly process.
2. Before beginning, please check the packing materials carefully for small parts which may have come
loose inside the carton during shipping. Please do not discard any packing material until all parts have been
located. If any parts are missing, please contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residues and rough surfaces and also check for staples or nails left after removing the packing materials.
The manufacturer will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts, nuts and wooden
plugs may loosen up. They should be periodically inspected and re-tightened to prevent damage to the furniture
and (or) peronal property or cause injury. Always check to be sure all hardware on this list and the below
mentioned components are attached to the furniture properly and kept tightened.
5. Please lay all parts and hardware on a non abrasive surface such as a carpet, and follow the assembly.
Hardware List:
2
QTYSKETCHDESCRIPTION
NO
1
SIZE
M6 X 70mm 4 PCS
This product will take 25-30
minutes to assemble
3
Screw driver is require for assembly (not included)
TIP: store the Allen key and or Wrench used in assembly in
this product's drawer or use masking or painter's tape to
affix it to the underside of the product. This will make it
easier to find if you want to periodically tighten bolts or
disassemble the product.
Components List:
B
QTYSKETCHDESCRIPTION
NO
ATABLE TOP
4 PCS LEG
C2 PCS
JOINT BLOCK
D1 PC
STRETCHER
E2 PCSMOUNTING PLATE
1 PC
5
4
JCBC BOLT
WITH WASHER
M6 X 40mm 16
PCS
4 PCS
JCBC BOLT WITH
SMALL WASHER
4 PCS
14.5mm
MADE IN MALAYSIA
JCBC BOLT
WITH WASHER
4 PCS
F1 PCSUPPORT SLAT
M6 X 40mm
61 PCALLEN KEY M4
WOODEN COVER
BUTTON
BARREL NUT M6

Step.3.1 Attach Mounting plate (E) to
Legs (B) top area, insert JCBC Bolt
with washer (2) through the pre-drilled holes
on Mounting plate (E) into Leg (B), tighten
JCBC Bolt (2) with washer with Allen Key (6)
provided as shown on FIG 3.1
Step 1.1 Install Joint block (C) to Legs (B)
using a mallet (not included) as shown on FIG 1.1
Step 2.1 Attach Stretcher (D) to Joint block (C), then
insert Barrel nut (4) into the pre-drilled holes on
Stretcher (D) as shown on FIG 2.1
Step 2.2 Insert JCBC Bolt with washer (1) through
the pre-drilled holes on Joint block (C) into
Stretcher (D), tighten JCBC Bolt (1) with washer
with Allen Key (6) provided as shown on FIG 2.2
Step 2.3 Insert Wooden cover button (5) into
Joint block (C) as shown on FIG 2.3
2 OF 3
WINNERS ONLY
®
ASSEMBLY INSTRUCTIONS
PROD. NO: DS54072
C
B
FIG 1.1
Screwdriver
(Not included)
3
FIG 2.1
6
1
5
FIG 2.3FIG 2.2
2
FIG 3.1
E
D
B
B
6
C

Step.5 Turn the table to a standing position.
Check the table balance and adjust the levelers
as needed.
Step 4.1 Attach the assembled leg frame to
Table top (A), insert JCBC Bolt with washer (2)
through the pre-drilled holes on Mounting plate
(E) into Table top (A), tighten JCBC Bolt
with washer (2) with Allen Key (6) provided
as shown on FIG 4.1
Step 4.2 Attach the Support slat (F) to
Table top (A), insert JCBC Bolt with small
washer (3) through the pre-drilled holes on
the Support slat (F) into Table top (A),
tighten JCBC Bolt with washer (3) with
Allen Key (6) provided as shown on FIG 4.2
Assembly is now complete.
3 OF 3
WINNERS ONLY
®
ASSEMBLY INSTRUCTIONS
PROD. NO: DS54072
2
FIG 4.1
6
A
Protective
surface
F
3
FIG 4.2
6