Winners Only BA2001CKHS User manual

PROD. NO.:
NOTE: Bunkie Board must be used to replace Box Spring.
NO QTY
A HB Left Leg 1 PC NO Description Size Sketcher QTY
B HB Right Leg 1 PC 1 Allen Key 4*74*29mm 1 PC
C Headboard 1 PC 2 Bolt 1/4"*15*57mm 6 PCS
D Wood stretcher 1 PC 3 Bolt 1/4"*15*45mm 4 PCS
G
Support Leg 6 PCS 6 Screw Ø8*30mm 26 PCS
7 Allen Key 4*74*29mm 1 PC
8 Bolt 1/4"*15*45mm 8 PCS
I Side Rail 2 PCS 9 Spring Washer 1/4"*11*2mm 8 PCS
J
Rail Cap 2 PCS 10 Flat Washer 1/4*18*2mm 8 PCS
Page 1 of 2 MADE IN VIETNAM
H
Slat Connector
2 PCS
Hardware List: BA2001CKRS
Storage Footboard
1 PC
5
Flat Washer
F
Slat Roll
1 SET
Hardware List: BA2001CKFS/BA2001KFS
Components List:BA2001CKFS/BA2001KFS
4
Spring Washer
1/4"*11*2mm
10 PCS
E
1/4*18*2mm
Components List:BA2001CKRS
WINNERS ONLY®
ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. Please read the instructions thoroughly before unpacking the assembly parts.
Caution: sharp exposed staple tips can cause injury, therefore for your protection, please remove any exposed staples used in packing.
Please keep all hardware parts out of the reach of children.
BA2001CKHS/BA2001KHS
BA2001CKFS/BA2001KFS
BA2001CKRS
DESCRIPTION
Hardware List: BA2001CKHS/BA2001KHS
Components List:BA2001CKHS/BA2001KHS
1. We recommend that you should assemble this product with the assistance of another person; this will make the assembly easier, and will help
to prevent personal injury and to insure parts are not damaged during the assembly process.
2. Before beginning, please check the packing materials carefully for small parts which may have come loose inside the carton during shipping. Please do not discard any packing
material until all parts have been located. If any parts are missing, please contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues and rough surfaces and also check for staples or nails left after
removing the packing materials. The manufacturer will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be periodically inspected and re-
tightened to prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure all hardware on this list and the below mentioned components are
attached to the furniture properly and kept tightened.
5. Please lay all parts and hardware on a non abrasive surface such as a carpet, and follow the assembly steps.
10 PCS
STEP 1
STEP 1:
Lay the Headboard (C) front side down on a smooth and clean
surface.
Attach HB Left Leg (A) and HB Right Leg (B) to Headboard (C) using
Flat Washer (
5), Spring Washer (4), Bolt (2). Do not fully tighten yet.
AttachWood Stretcher (D) to HB Left (A) and HB Right legs (B) using
Flat Washer (
5), Spring Washer (4), Bolt (3), fully tighten with Allen
Key (1).
Fully tighten all the bolts located in HB Left Leg (A) and HB Right Leg
(B).
FIG 1
(C)
(A)
(B)
(D)

PROD. NO.:
Page 2 of 2 MADE IN VIETNAM
WINNERS ONLY®
ASSEMBLY INSTRUCTIONS
BA2001CKHS/BA2001KHS
BA2001CKFS/BA2001KFS
BA2001CKRS
(I)
STEP 2
FIG 3
STEP
2: Hook both Side Rails (I) to the Headboard
assembly and to the Footboard (E) as shown in FIG
2.
FIG 2
STEP 3
(F)
(E)
(F)
(H)
(G)
STEP 3: Attach Support Legs (G) to the Slat Connector (H)
and Slat Roll (F) as shown in FIG
3 .
STEP
4: Attach Slat Roll (F) with Support Legs and Slat
Connector (G&H) to the Side Rails (I) using Screws (6) as
shown in FIG
3.
STEP 4
STEP 5: Attach the rail cap (J) to side rail (I), using bolt(8),
spring washer (9), flat washer (10) and tighen them by
Allen Key (7).
STEP 5
(F)
(F)
(J)