WolfPack HDTV-412 User manual

Thank you for purchasing this product. For optimum performance and
safety, please read the instructions carefully and keep the manual for
future reference.
·
Important Safety Notice
Please read below safety instructions carefully before installation
and operation:
* Please pay attention to all the warnings and hints on this device.
* Do not expose this unit to rain, moisture and liquid.
* Do not put any stuff into the device.
* Do not repaire the device or open the enclosure without professional
person guidence to avoid electronic shock.
* Make sure good ventilation openings to avoid product overheating
damage.
* Turn off power and make sure environment is safe before installation.
* Do not plug-in/out the connection cables when it is in using to avoid
cables damage.
* Use DC12V/2A power adapter. Make sure the specification matched if
using 3rd party DC adapters.
·
Introduction
This product is a 4×2 HDMI2.0 Matrix Switch, supports resolution up to
4K×2K@60Hz, with 4 HDMI inputs and 2 HDMI outputs. 4 HDMI inputs
accommodate the simultaneous connection up to 4 high definition
video sources, such as satellite systems and Blu-ray players. 2 HDMI
outputs send the high definition A/V signals to 2 ultra HD displays.
This Matrix Switch supports IR remote control, button control and
RS232 for switching inputs and outputs. This product is perfect for
security system, digital monitoring system, school education system,
exhibition center, multimedia conference, command system etc.
·
Features
1.Support 4-way HDMI signal input, switching or distributing
to 2 display devices that support HDMI signal input.
2.Supports up to ultra HD resolution 4K×2K@60Hz.
3. Transmission data rate up to 18Gbps.
4. Pure hardware design, plug and play.
5. Support IR remote and button control for
switching inputs/outputs.
6. Support RS232 control.

7. Supports YUV 4:4:4.
8. Support 3D.
·
Package Contents
Matrix Switch unit ×1pcs DC12V2A power User manual ×1pcs
adapter ×1pcs
Remote Controller ×1pcs Wall-mount kit x2pcs
·
Installation Requirement
1. HDMI source device (DVD, PS3, Set top box, PC etc)
2. HDMI display device like SDTV, HDTV, and projector with HDMI port.
·
Panel Description
Front Panel

Back Panel
·
Remote Controller
This remote controller is just used for inputs
or outputs switched/selected.
·
Connections
1. Connection Drawing

1) Connect all your HDMI source devices to this product's inputs
via HDMI cables.
2) Connect up to the HD display devices on the HDMI outputs via
HDMI cables.
3) Power on all source device, this Matrix Switch and display device,
then it works.
4) Select/switch inputs and outputs via IR remote , buttons or
RS232 command.
2. RS232 control
1) It supports RS232 control to select the input and output channel, the
baud rate is 9600, and the connector is a 9-pin port.
2) Use the serial port software, please set COM firstly, and then
correspond to the following figure in the various channel commands.
·
FAQ
Q: No video/audio signal output on the displays?
A: 1) Please check and make sure the Matrix Switch is connected well
and powered on.
2) Please check and make sure all HDMI cables are connected well
3) Please check and make sure the input channel of displays are
correct.
Q: Picture quality is not fluent and stable ?
A: 1) Please check and make sure all HDMI cables are connected well
2) Try to connect the source device to display device directly, or

change to another source device for a try to see the picture quality.
3) Please use high quality HDMI2.0 standard cable when HDMI 4Kx2K
signal input.
·
Specification
Disclaimer
The product name and brand name may be registered trademark of
related manufacturers.TM and ® may be omitted on the user manual.
The pictures on the user manual are just for reference, and there may be
some slight difference with the real products.We reserve the rights to
make changes without further notice to a product or system described
herein to improve reliability, function or design.