Woodbridge B0940 User manual

ONE PIECE TOILET
MPN: B0940
INSTALLATION INSTRUCTIONS

TOOLS REQUIRED FOR INSTALLATION
TOILET COMPONENTS
1
ONE PIECE TOILET
One piece toilet
with soft-close
toilet seat x1 Wax Ring x1
Washers x2
Nuts x2 Closet
Bolts x2
Soft Cloth
or Blanket
Silicone Silicone/
Caulk Gun
OTHER TOOLS MAY BE REQUIRED
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT
2 PEOPLE ARE REQUIRED TO LIFT AND DURING
ENTIRE INSTALLATION OF THIS PRODUCT
INSTALLATION OF THIS PRODUCTS BY AN
INEXPERIENCED INSTALLER MAY RESULT
PERSONAL INJURY OR DEATH!
INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING
OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
We reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice!
It is your responsibility to visit website to download or contact customer service for the most updated version of the installation instructions.
We shall not be liable for any injuries or property damages in connection with this product during installation or use of this product!
Tape
Measure
Pencil/Marker Safety Glass Knife
During unpacking the product and prior to installation inspect your new product for any damages or
missing parts. Do not attempt to install or operate the product if the product is damaged.
Adjustable
Wrench
Channel
Lock Pliers
Adjustable
Socket Extension
Philips
Screwdriver
Hand
Wrench Level Putty Knife
This products must be installed by a fully insured and licensed plumber only. Installation of any our product by anyone other
than fully insured and licensed plumber shall void limited warranty. We recommends that such licensed plumber have experience
in the installation of products.
Limited warranty is void on any commercial installation
We are not responsible for local code compliance for this product. Building and plumbing codes may vary from state-to-state in
accordance to your location. We are not resonsible for providing any compliance certications.
We are not responsible to provide any type of certications for this product
Under no circumstances we are shall not be liable for any and all incidental damages sustained in connection with this product
Neither manufacture, nor distributor, nor retailer is responsible for water damage or ood caused due to use of this product.
Under no circumstances We shall not be liable for any and all fees, cost of installation/reinstallation/removal, subsequent
damage or transportation in case of the product defect

2
ONE PIECE TOILET
DIMENSIONS/TECHNICAL DATA
TECHNICAL DATA
• Dual ush: 1/1.6 GPF
ATTENTION! Dimensions may vary by up to 3/8". It is highly recommended to pull
all dimensions of actual model for installation and measuring purposes.
18"
28 1/2"
12"
5 1/2"
Rough-in
Standard
16 1/2"
14 1/2"
15 3/8"
10 1/4"
1 1/2"
2 1/2"
11 "
27 1/2"
7 1/4"
2" 1 1/2"
13"
14 1/4"

12"
5 1/2"
5 1/2"
Rough-in
Standard
Wall
Floor
ONE PIECE TOILET
WATER SUPPLY LOCATION & TECHNICAL INFORMATION
TECHNICAL DATA
• Dual ush: 1/1.6 GPF
3
ATTENTION! Dimensions may vary by up to 3/8". It is highly recommended to pull
all dimensions of actual model for installation and measuring purposes.
12"
5 1/2"
5 1/2"
3"
15"
Rough-in
Standard
5 1/2"
12"
4 1/2"
10"
Supply
Position 1
Threaded
Shunk (Water
Supply Fill Valve)
Side View
Side View
Back View
Supply
Position 2
Wall
Floor
Flush GPF amount is factory
set. No additional adjustment
is required.
Tank Top View (Inside)
Half
Flush
(1GPF)
You may connect the water supply line using two dierent
options. In both options distance from the oor to the
center of the supply line must be 5 1/2". In Supply Position
1, the water supply is located behind the toilet and is
oset by 4 1/2" from the installed toilet's center. In supply
Position 2 the water supply line must oset by 10" from
the center of the installed toilet.
Adjust the water level in the
toilet's tank if neccessary by
rotating the adjustment
screw to increase (+) or
decrease (-) a level of water
in the toilet's tank.
Full
Flush
(1.6GPF)
Half
Flush
(1GPF)

4
ONE PIECE TOILET
INSTALLATION INSTRUCTIONS
IMPORTANT!
Shut off main water supply prior to installation!
REMOVE OLD TOILET
1. Shut o water supply line. If you do not have shut-o valve near the toilet shut o main water supply line.
2. Flush the old toilet and make sure that tank is empty.
3. Disconnect and remove water supply line connected to the toilet's tank.
4. Remove old toilet, bolts, nuts from the closet ange.
5. Clean closet ange area from old wax ring and putty sealant using putty knife from the base area.
6. Clean any remaining debris and wipe any water at the installation area
7. Temporarily plug ange on a oor with a ange plug or towel to prevent gasses from escaping
PREPARE CLOSET FLANGE
Figure 1 Figure 2
Step 1 Step 2
Make sure that rough-in is 12" by measuring the
distance from the wall to the center of the closet
ange.
See Figure 1
Step 1. Insert 2 oor bolts inside of the toilet ange
Step 2. Slide the closet bolts through the holes and
align bolts horizontaly.
See Figure 2
Bathroom
Wall
Bathroom
Floor
Closet Flange
12"
Rough-in
Figure 3
INSTALL WAX RING
Important: safety glasses must be worn by the installer
and all bystanders.
Cover the oor with a soft-close blanket. Carefully turn the
toilet on it's side or upside-down on the blanket with
assistance of a second person. Install wax ring over the
horn discharge located on the bottom of the toilet's bowl.
See Figure 3
Note: Ceramic is a fragile material. You must always cover
the oor with a soft-cloth blanket if you want to put the
toilet on the oor on any side other than the bottom of
the toilet. If you do not cover the oor with a soft-close
blanket contact of the toilet with the oor may and will
cause minor or moderate scratches on the toilet's surface.
Prior to installtion the
wax ring must be kept in
a room temperature
between 70-75ºF.
90º
90º
IMPORTANT! The mounting surface area
must be clean, dry, and leveled prior to
installation of the new toilet!
NOTE! Inspect the existing closet ange for
damages. If damaged, replace it to new ange
before proceeding to the installation
Always Use Soft-Cloth Blanket