woodmizer D19 Guide

D19 Engine
Safety, Operation, Maintenance
& Parts Manual
LT15 rev. E4.04 - E8.13
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
April 2010
Form #1355

©2019
Printed in the United States of America, all rights reserved. No part of this manual may be
reproduced in any form by any photographic, electronic, mechanical or other means or used in
any information storage and retrieval system without written permission from
Wood-Mizer
8180 West 10th Street
Indianapolis, Indiana 46214
&DOLIRUQLD
3URSRVLWLRQ:DUQLQJ
:$51,1*%UHDWKLQJJDVGLHVHOHQJLQHH[KDXVWH[SRVHV\RXWRFKHPLFDOVNQRZQWR
WKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHUDQGELUWKGHIHFWVRURWKHUUHSURGXFWLYHKDUP
$OZD\VVWDUWDQGRSHUDWHWKHHQJLQHLQDZHOOYHQWLODWHGDUHD
,ILQDQHQFORVHGDUHDYHQWWKHH[KDXVWWRWKHRXWVLGH
'RQRWPRGLI\RUWDPSHUZLWKWKHH[KDXVWV\VWHP
'RQRWLGOHWKHHQJLQHH[FHSWDVQHFHVVDU\
)RUPRUHLQIRUPDWLRQJRWRZZZ3ZDUQLQJVFDJRY
:$51,1*'ULOOLQJVDZLQJVDQGLQJRUPDFKLQLQJZRRGSURGXFWVFDQH[SRVH\RXWR
ZRRGGXVWDVXEVWDQFHNQRZQWRWKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHU$YRLGLQKDOLQJ
ZRRGGXVWRUXVHDGXVWPDVNRURWKHUVDIHJXDUGVIRUSHUVRQDOSURWHFWLRQ
)RUPRUHLQIRUPDWLRQJRWRZZZ3:DUQLQJVFDJRYZRRG

Table of Contents Section-Page
Table of Contents WMdoc072619 iii
TOC
SECTION 1 ABOUT THIS MANUAL 1-1
SECTION 2 OPERATION 2-1
2.1 Starting The Engine................................................................................2-1
SECTION 3 MAINTENANCE 3-1
3.1 Safety......................................................................................................3-1
3.2 Cooling System ......................................................................................3-2
3.3 Air Filter & Pre-Cleaner.........................................................................3-2
3.4 Fuel Filter ...............................................................................................3-2
3.5 RPM Adjustments ..................................................................................3-2
SECTION 4 REPLACEMENT PARTS 4-1
4.1 Fuel Tank................................................................................................4-1
LT15 Rev. E8.08+
LT15W Rev. A1.08+
4.2 Fuel Tank................................................................................................4-2
LT15 Rev. E6.05 - E8.07
LT15W Rev. A1.00 -A1.07
4.3 Engine Assembly....................................................................................5-1
LT15 Rev. E1.00+
4.4 Throttle/Clutch Assembly ......................................................................5-3
INDEX I

About This Manual
1
1-1 WMdoc072619 About This Manual
SECTION 1 ABOUT THIS MANUAL
This manual is provided as a supplement to the equipment manufacturer’s manuals. This
manual provides information specific to the use of this equipment on the Wood-Mizer®
sawmill. Refer to the sawmill operator’s manual and manufacturer's manual before
attempting to operate this equipment.
IMPORTANT! Read the sawmill operator’s manual and engine manu-
facturer’s manual for instructions and safety precautions before oper-
ating this equipment.
The information and instructions given in this manual do not amend or extend the limited
warranties for the equipment given at the time of purchase.

Operation
Starting The Engine
Operation WMdoc072619 2-1
2
SECTION 2 OPERATION
2.1 Starting The Engine
DANGER! Ensure the blade is disengaged and all persons are out of
the path of the blade before starting. Failure to do so will result in death
or serious injury.
DANGER! Operate your engine only in well ventilated areas. The
exhaust gases of your engine can cause nausea, delirium, and poten-
tially death unless adequate ventilation is present.
DANGER! Never operate an engine with a fuel or oil leak. This is a fire
hazard, which may cause serious injury or death.
WARNING! Do not operate engine without proper and operational
spark arrester/muffler. Sparks emitted from the engine exhaust could
ignite surrounding materials, causing serious injury or death.
1. See the engine manufacturer’s manual for lubricating oil recommendations.
2. Use #2 or better quality diesel fuel for above freezing starting. Use a #1 quality diesel fuel
for below freezing starting.
3. Turn the key switch to the on (#1) position.
4. Turn the key switch to the start (#2) position and release.
ENGINE SHUTOFF
Turn the key switch to the off (#0) position.

Maintenance
Safety
3
3-1 WMdoc072619 Maintenance
SECTION 3 MAINTENANCE
Refer to the manufacturer’s manual for maintenance intervals and procedures unless oth-
erwise instructed in this manual. Follow the manufacturer’s recommendations for dusty
conditions.
IMPORTANT! This manual only provides information about additional
procedures or procedures to be performed at different time intervals
than found in the manufacturer's manuals. Refer to the manufacturer's
manual for complete maintenance instructions.
WARNING! Clean sawdust from all guards, vents, control
boxes, or any area where sawdust may gather after every
shift. Failure to do so may result in fire, causing death or
serious injury.
3.1 Safety
Use caution when performing maintenance or service to the engine.
DANGER! Always be aware of and take proper protective measures
against rotating shafts, pulleys, fans, etc. Always stay a safe distance
from rotating members and make sure that loose clothing or long hair
does not engage rotating members resulting in possible injury.
DANGER! Engine components can become very hot during operation.
Avoid contact with any part of a hot engine. The exhaust components
of your engine are especially hot during and following operation. Con-
tact with hot engine components can cause serious burns. Therefore,
never touch or perform service functions on a hot engine. Allow the
engine to cool sufficiently before beginning any service function.
WARNING! Remove the blade before performing any engine service.
Failure to do so may result in serious injury.
WARNING! Always wear proper and necessary safety equipment
when performing service functions. Proper safety equipment includes
eye protection, breathing protection, hand protection and foot protec-
tion.
This symbol identifies the interval (hours of operation) at which each maintenance pro-
cedure should be performed. "AR" signifies maintenance procedures which should be
performed as required.
0

Maintenance
Cooling System
Maintenance WMdoc072619 3-2
3
3.2 Cooling System
Wash the engine or brush off sawdust and debris every 50 hours of operation. Remove
any dust, dirt or oil. See engine manual for further instructions.
3.3 Air Filter & Pre-Cleaner
WARNING! Always wear proper and necessary safety equipment
when performing service functions. Proper safety equipment includes
eye protection, breathing protection, hand protection and foot protec-
tion.
Service the pre-cleaner every four hours of operation. Service by gently shaking excess
sawdust and debris from the foam piece.
Clean the air filter (air cleaner element) and pre-cleaner (element wrapper) every eight
hours of operation. See the engine manual for further instructions.
Replace the air filter (cleaner) every 200 hours of operation.
Replace the pre-cleaner (element wrapper) every 2000 hours of operation.
3.4 Fuel Filter
Replace the fuel filter every 100 hours of operation or as required for engine perfor-
mance.
3.5 RPM Adjustments
WARNING! Remove the blade before performing any engine service.
Failure to do so may result in serious injury.
Check the RPM with a tachometer every 200 hours of operation.
50
4
8
200
2000
100
200

Maintenance
RPM Adjustments
3
3-3 WMdoc072619 Maintenance
See Table 3-1.
Before checking the RPM, make sure belt and brake strap tensions are correct (See Saw-
mill Maintenance). Also check oil, fuel, and coolant levels.
Make sure the throttle cable does not affect the engine RPM when the clutch handle is
disengaged. Make sure the cable is not bent or kinked.
Engine High End RPM Low End RPM
D19 3600 1500
TABLE 3-1

Replacement Parts
Fuel Tank
Replacement Parts 15D19doc072619 4-1
4
D19
SECTION 4 REPLACEMENT PARTS
4.1 Fuel Tank
LT15 Rev. E8.08+
LT15W Rev. A1.08+
REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.
TANK ASSEMBLY, 5 GALLON DIESEL 074828 1
1Weldment, Fuel Tank Tray 103802 1
2Cover, Fuel Tank 103867 1
Tank, 5 Gallon Low Pro Diesel 103928 1
3Cap, Fuel Tank Diesel 080185BE 061257 1
4Fitting, Pick-Up/Tube Diesel 468871A 061255 1
5Grommet, Shut Off 046881 061250 2
6Fitting, Return/tube Diesel 468489 061256 1
7Bolt, 5/16-18 x 3/4” Hex Head w/Flat&Lock Washer F05006-101 4
8Bolt, 3/8-16 x 3” Hex Head Grade 5 F05007-73 2
9Nut, 3/8-16 Hex Nyloc F05010-10 2
10 Washer, 3/8” Flat SAE F05011-3 2
Hose, Fuel 5/16" EPA 15G CARB R02423-3 8 Ft.
Hose, Fuel 1/4" EPA 15G CARB R02423-2 8 Ft.
Weldment, Fuel Tank Tray 103802 1
Clamp, 7/32in-5/8in Hose P649 2
Clamp, 1/2EMT Coated P07584 1
1
2
3
4
5
6
7
8
9
10
150245B

Replacement Parts
Fuel Tank
4
4-2 15D19doc072619 Replacement Parts
D19
4.2 Fuel Tank
LT15 Rev. E6.05 - E8.07
LT15W Rev. A1.00 -A1.07
REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.
TANK ASSEMBLY, 5 GALLON DIESEL A12132 1
1Tank, 5 Gallon Fuel P12166 1 
2Pickup, 9" Fuel P12172 2
3Cap, 3/5 Gallon Fuel Tank P09683 1
4Fitting, 1/4” NPT Male Quick Disconnect 015583 1
5Fitting, Female Quick Disconnect Barb 015582 1
6Fitting, 1/4" NPT Plastic Female Disconnect P12175 1
7Fitting, 1/4” Barb Plastic Male Disconnect P12176 1
8 CLAMP, 7/32”-1/2” HOSE P649 4
9 HOSE, 5/16” FUEL LINE 016338 7 Ft
10 HOSE, 1/4” ID FUEL P642 9.3 Ft
1
2
2
3
6
7
8
5
10
10
10
10
9
150137-4C
4

Replacement Parts
Engine Assembly
Replacement Parts 15D1905doc072619 4-1
4
D19
4.3 Engine Assembly
LT15 Rev. E1.00+
REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.
ENGINE ASSEMBLY, LT15 19HP DIESEL 038570 1
1Engine, 19HP Deutz Diesel 049387 1 
Filter, Air #7700 175 180480 054911 1
Pump, Fuel #7700 6521 180420 054912 1
Filter, Oil #7700 217 52020 054913 1
Starter, Engine #7700 563 180540 054914 1
Shutdown, Engine #7700 674 180470 054915 1
Filter, Fuel 014209 1
2Screw, #10-24 x 1/2” Self-Tapping F05015-7 1 1
3Deflector, 1 1/4” ID Exhaust D19 038590 1
1
2
3
23
4
5
6
7
8
9
10
11
12
13
14
14
15
22
16
16
20
19
17
21
18
150137-1C

Replacement Parts
Engine Assembly
4
5-2 15D1905doc072619 Replacement Parts
D19
4Sheave, 3V5.6 x 2-SH 047742 1
5Bushing, SH x 1 1/8” 038432 1
6Key, 1/4” x 1 11/16” S04124 1
7Plate, Throttle D19 049399 1
8Cable, LT15/LT28 D19 049406 1
9Fitting, M14x1.5 Male-1/4 NPT Female 038584 1
10 Fitting, 1/4” NPT Male 90 Deg 3/8” NPT Fem 038571 1
11 Hose, 3/8” NPT x 9 5/8” Rubber P10082 1
12 Cap, 3/8 Pipe Galvanize P04332 1
13 Plate, Engine Mount D19 049389 2 1
14 Bolt, 3/8-16 x 1 1/4” Carriage Gr5 F05007-127 8
15 Washer, 3/8” Flat SAE F05011-3 2 4
16 Nut, 3/8-16 Hex Nylon Lock F05010-10 8
17 Plate, 1/4” Spacer D19 038572 1
18 Spacer, 13/32” ID x 1 1/4” OD x 1/4” 038573 4
19 Bracket, LT15 D19 Filter Mount 038574 1
20 SUPPORT WELDMENT, DRIVE BELT 048237 1
21 BOLT, 3/8-16 X 3/4” HEX HEAD GRADE 5 F05007-118 1
22 NUT, 3/8-16 SELF-LOCKING HEX F05010-19 1
23 BELT, 2/3VFL900 DRIVE 047751 1
1 Screw used instead of P09900 clamp.
2 Mount Plate 049389 modified 6/06 to provide clearance for throttle spring. Four Flat Washers F05011-3 removed to provide proper
engagement of lock nut on bolt.

Replacement Parts
Throttle/Clutch Assembly
Replacement Parts 15D1905doc072619 4-3
4
D19
4.4 Throttle/Clutch Assembly
REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.
1 KNOB, 5/8-11 BALL P04211 1
2 HANDLE, LT15 CLUTCH 016487 1 1
3 SCREW, 3/8-16 X 3/8” SOCKET HEAD CUP PT SET F05007-68 2
4 ACTUATOR WELDMENT, THROTTLE LT15D&G 034815 1
5 LINKAGE, THROTTLE LT15D&G 034818 1
6 BOLT, 1/4-20 X 1/2” HEX HEAD F05005-15 1
7 NUT, 1/4-20 SWAGED F05010-21 1
8 BUSHING, 5/8” ID X 7/8” OD X 1 1/8” LONG FL BRONZE 016486 2
9 BLOCK WELDMENT, LINKAGE CLUTCH/BRAKE 034612 1
10 PIN, 3/16” X 1 1/4” ROLL F05012-16 1
LINKAGE ASSEMBLY, W/BEARING 034605 1
11 Link Weldment, Clutch/Brake 034604 1 
12 Bushing, 5/8” ID x 7/8” OD x 1 1/8” Long Fl Bronze 016486 1
13 NUT, 1/2-13 FREE HEX, ZINC F05010-35 1
1
2
3
4
5
67
8
12
8
910
11
13
14
15
32 33
16
17
17
18
19
20
21 22
23
24 25
26
26
27
28
150137-2E

Replacement Parts
Throttle/Clutch Assembly
4
4-4 15D1905doc072619 Replacement Parts
D19
14 WASHER, 1/2” SPLIT LOCK F05011-9 1
15 NUT, 1/2-13 JAM F05010-31 1
16 PIVOT WELDMENT, CLUTCH/BRAKE 034608 1
17 BUSHING, 1” X 1 1/4” X 3/4” FLG BRONZE P737 2
BRAKE/CLUTCH ASSEMBLY, LT15 065874 2 1
18 Arm Weldment, Clutch/Brake LT15 065873 1
19 Bolt, 3/8-16 x 2” Hex Head Gr5 F05007-124 1
20 Nut, 3/8-16 Hex Nylon Lock F05010-10 1
21 Block, LT15 Brake 016488 2
22 Screw, 10-24 x 1” Socket Head F05004-2 4
23 Nut, #10-24 Keps F05010-14 8
24 Idler, 4" O.D. x 3/8” Bore 034602 1
25 Bolt, 3/8-16 x 2-3/4” Hex Head Gr5 Full Thread F05007-230 2 1
26 Washer, 3/8 Flat F05011-3 2
27 Nut, 3/8-16 Swaged Lock F05010-25 2
28 Spring, Idler Arm LT15D/E/G 034810 1
29 Screw, 10-24 x 5/8” FSHC F05004-282 4
30 Plate, Brake Adjustment 065872 2
31 Washer, #10 SAE Flat F05011-18 4
1 Clutch Handle 016487 modified Rev. E6.01 to eliminate possible pinch point with feed rope pulley with saw head at certain heights.
2 Replaces Brake/Clutch Assembly 034603 to improve durability (Rev. E7.01). Brake/Clutch Assembly 034603 (including Clutch/Brake
Arm Weldment 034613) modified 9/10. Spring mount hardware changed to provide more freedom of movement and prevent binding
point in spring.

Index 15D1905doc072619 i
M
maintenance 3-1
air cooling system 3-2
fuel filter 3-2
RPM adjustments 3-2
P
parts list
engine assembly 5-1
fuel tank 4-1, 4-2
S
starting 2-1
INDEX