woodmizer E10 Guide

WARNING! Read and understand this
manual before using this machine.
!
E10 Motor
Safety, Operation, Maintenance
& Parts Manual
034812 Motor, LT15 10Hp 3Ph rev. A-B
017957 Motor, LT15 10Hp 3Ph 575V rev. A-B
Safety is our #1 concern!
Form #1099
Used with
LT15E10H rev. E8.14
LT15E10HW rev. A2.00
LT15E10L rev. E8.14
LT15E10L-ICE rev. E8.14
LT15E10LW rev. A2.00
LT15E10C rev. E6.05

Active Patents assigned to Wood-Mizer, LLC
Wood-Mizer, LLC has received patents that protect our inventions which are a result of a dedication to
research, innovation, development, and design. Learn more at: woodmizer.com/patents
©2023 Wood-Mizer LLC
Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any
photographic, electronic, mechanical or other means or used in any information storage and retrieval system without
written permission from
Wood-Mizer, LLC
8180 West 10th Street
Indianapolis, Indiana 46214

Table of Contents Section-Page
Table of Contents WM doc 12/5/23 iii
SECTION 1 SAFETY 1-1
1.1 Safety ..................................................................................................... 1-1
SECTION 2 OPERATION 2-1
2.1 Starting The Motor................................................................................. 2-1
SECTION 2 MAINTENANCE 2-1
2.1 Safety ..................................................................................................... 2-1
SECTION 3 REPLACEMENT PARTS 3-1
3.1 Motor Starter Assembly ........................................................................ 3-1
3.2 Motor Assembly..................................................................................... 3-3
3.3 Throttle/Clutch Assembly .................................................................... 3-4

Introduction
Safety
1
1-1 WM doc 12/5/23 Introduction
SECTION 1 SAFETY
This manual is provided as a supplement to the equipment manufacturer’s manuals.
This manual provides information specific to the use of this equipment on the Wood-Mizer® sawmill. Refer to the sawmill
operator’s manual and manufacturer's manual before attempting to operate this equipment.
NOTICE Read the sawmill operator’s manual and engine manufacturer’s manual for instructions
and safety precautions before operating this equipment.
The information and instructions given in this manual do not amend or extend the limited warranties for the equipment
given at the time of purchase.
Refer to the manufacturer’s manual for maintenance intervals and procedures unless otherwise instructed in this manual.
Follow the manufacturer’s recommendations for dusty conditions.
NOTICE This manual only provides information about additional procedures or procedures to be
performed at different time intervals than found in the manufacturer's manuals. Refer to the man-
ufacturer's manual for complete maintenance instructions.
WARNING! Clean sawdust from all guards, vents, control boxes, or any area where
sawdust may gather after every shift. Failure to do so may result in fire, causing
death or serious injury.
1.1 Safety
Use caution when performing maintenance or service to the engine.
DANGER! Take proper protective measures against rotating shafts, pulleys, fans, etc.
Ensure loose clothing or long hair does not engage rotating members.
DANGER! Do not touch or perform service functions on a hot engine. Allow the engine to cool
sufficiently before beginning any service function. Hot engine components will cause serious
burns.
WARNING! Remove the blade before performing any engine service.
WARNING! Wear eye, hand, and foot protection equipment when performing service functions.

Operation
Starting The Motor 2
Operation WM doc 12/5/23 2-1
SECTION 2 OPERATION
2.1 Starting The Motor
DANGER! Ensure the blade is disengaged and all persons are out of the path of the blade
before starting. Failure to do so will result in death or serious injury.
Turn the main switch on the starter box to the ON position.
Press the green START button located on the starter box to start the motor.
MOTOR SHUTOFF
Press the red STOP button on the starter box to stop the motor.
Turn the main switch to the OFF position.
SECTION 2 MAINTENANCE
Refer to the manufacturer’s manual for maintenance intervals and procedures unless otherwise instructed in this manual.
Follow the manufacturer’s recommendations for dusty conditions.
NOTICE This manual only provides information about additional procedures or procedures to be
performed at different time intervals than found in the manufacturer's manuals. Refer to the man-
ufacturer's manual for complete maintenance instructions.
WARNING! Clean sawdust from all guards, vents, control boxes, or any area where
sawdust may gather after every shift. Failure to do so may result in fire, causing
death or serious injury.
2.1 Safety
Use caution when performing maintenance or service to the motor.
DANGER! Take proper protective measures against rotating shafts, pulleys, fans, etc.
Ensure loose clothing or long hair does not engage rotating members.
DANGER! Ensure all electrical installation, service and/or maintenance work is performed by a
qualified electrician and is in accordance with applicable electrical codes.
DANGER! Hazardous voltage inside the disconnect box, starter box, and at the motor can cause
shock, burns, or death. Disconnect and lock out power supply before servicing! Keep all electrical
component covers closed and securely fastened during mill operation.
WARNING! Remove the blade before performing any engine service.
WARNING! Wear eye, hand, and foot protection equipment when performing service functions.

Replacement Parts
Motor Starter Assembly
3
3-1 WM doc 12/5/23 Replacement Parts
SECTION 3 REPLACEMENT PARTS
3.1 Motor Starter Assembly
REF PART # DESCRIPTION COMMENTS QTY.
017954 MOTOR MODULE, 10HP 3-PHASE 208-240V
ELECTRIC MOTOR
1
017955 MOTOR MODULE, 10HP 3-PHASE 380-500V
ELECTRIC MOTOR
1
Motor Parts () (See Section 4.4)
053713 Control Assembly, LT15 E10 3-Phase 240V 1
053738 Control Assembly, LT15 E10 3-Phase 460V 1
1F05006-5 Bolt, 5/16-18 x 3/4 Hex Head 4

Replacement Parts WM doc 12/5/23 3-2
Replacement Parts
Motor Starter Assembly 3
2035991 Bracket, Front Electric Motor Mount 1
3035992 Bracket, Rear Electric Motor Mount 1
4053584 Enclosure, 16” x 16” x 8” Custom 1
LT15E10L Electrical Components ( See Component List)
LT15E10H Electrical Components ( See Component List)
LT15E10S Electrical Components (See Component List)
5F05011-16 Washer, 5/16 Flat 4
6F05010-20 Nut, 5/16-18 Keps 4
7053714 Harness Assembly, LT15E10L Blade
Motor (3-Phase 240V)
1
053739 Harness Assembly, LT15E10H Blade
Motor (3-Phase 460V)
1
8S20061 Decal, Electrical Hazard Danger 1
9069362 Decal, LT15E10 Control Cabinet 1
10 034906 TUBE WELDMENT, WIRE HANGER LT15E 1
11 034899 MOUNT WELDMENT, BATTERY/CONTROL BOX 1
12 F05006-102 BOLT, 5/16-18 X 3/4” HEX HEAD 4
13 F05010-58 NUT, 5/16-18 NYLON LOCK 4
14 F05007-7 BOLT, 3/8-16 X 1” HEX HEAD 3
15 F05011-4 WASHER, 3/8” SPLIT LOCK 3
16 F05011-3 WASHER, 3/8” SAE FLAT 3
17 P05436 CLAMP, 1” EMT 1
REF PART # DESCRIPTION COMMENTS QTY.

Replacement Parts
Motor Assembly
3
3-3 WM doc 12/5/23 Replacement Parts
3.2 Motor Assembly
REF PART # DESCRIPTION COMMENTS QTY.
P12393 Cover, Engine 1
034812 MOTOR ASSEMBLY, LT15 10HP 3-PHASE ELEC-
TRIC
1
017957 MOTOR ASSEMBLY, LT15 10HP 575 VOLT ELEC-
TRIC
1
1034903 Motor, 10HP 3-phase Lincoln Available in assemblies only. 1
034907 Motor, 10HP 3-phase 575V Lincoln 1
2P04864 Bushing, 1 3/8 Split Taper 1
3036057 Sheave, BK45QT 1
4F05007-129 Bolt, 3/8-16 X 1 3/4” Hex Head Grade 5 4
5034807 Spacer, Motor Lt15e 2
6F05010-10 Nut, 3/8-16 Hex Nylon Lock 4
7P25301 Belt, Bx85 Drive 1
8034904 Guard, Motor Shaft Lt15e 1
9F05007-7 Screw, 3/8-16 X 1 Hex Head 2
10 F05011-3 Washer, 3/8 Flat Sae 2
11 F05010-10 Nut, 3/8-16 Hex Nylon Lock 2
12 S20097 Decal, Motor Direction 1
13 036058 Decal, E10 Electric Motor Wiring 1

Replacement Parts WM doc 12/5/23 3-4
Replacement Parts
Throttle/Clutch Assembly 3
3.3 Throttle/Clutch Assembly
REF PART # DESCRIPTION COMMENTS QTY.
1P04211 KNOB, 5/8-11 BALL 1
2016487 HANDLE, LT15 CLUTCH 1
3016486 BUSHING, 5/8 ID X 7/8 OD X 1 1/8 LONG FL
BRONZE
3
4P05035 COLLAR, 5/8 ID LOCK 1
5065572 BLOCK WELDMENT, LINKAGE CLUTCH/BRAKE . 1
6F05012-16 PIN, 3/16 X 1 1/4 ROLL 1
7034605 LINKAGE ASSEMBLY, W/BEARING 1
8F05010-35 NUT, 1/2-13 FREE HEX, ZINC 1
9F05011-9 WASHER, 1/2 SPLIT LOCK 1
10 F05010-31 NUT, 1/2-13 JAM 1
11 034608 PIVOT WELDMENT, CLUTCH/BRAKE 1
12 P737 BUSHING, 1 X 1 1/4 X 3/4 FLANGE BRONZE 2
065874 BRAKE/CLUTCH ASSEMBLY, LT15 1
13 065873 Arm Weldment, Clutch/Brake LT15 1
14 F05007-124 Bolt, 3/8-16 x 2 Hex Head Gr5 1
15 F05010-10 Nut, 3/8-16 Hex Nylon Lock 1
16 016488 Block, LT15 Brake 2
17 F05004-2 Screw, 10-24 x 1 Socket Head 4
18 F05010-14 Nut, #10-24 Keps 8
19 034602 Idler, 4" O.D. x 3/8 Bore 1

Replacement Parts
Throttle/Clutch Assembly
3
3-5 WM doc 12/5/23 Replacement Parts
20 F05007-230 Bolt, 3/8-16 x 2-3/4” Hex Head Gr5 Full
Thread
1
21 F05011-3 Washer, 3/8 Flat 2
22 F05010-25 Nut, 3/8-16 Swaged Lock 2
23 034810 Spring, Idler Arm LT15/D/E/G 1
24 F05004-282 Screw, 10-24 x 5/8” FSHC 4
25 065872 Plate, Brake Adjustment 2
26 F05011-18 Washer, #10 SAE Flat 4
REF PART # DESCRIPTION COMMENTS QTY.