Woodward easYgen 3000XT Series User manual

Option Manual
easYgen-3000XT Series
Genset Control
Release 2.12-1
Document ID: 37595, Revision A - Build 51340
easYgen-3000XT Rental

Manual (original)
This is no translation but the original Technical Manual in English.
Designed in Germany.
Woodward GmbH
Handwerkstr. 29
70565 Stuttgart
Germany
Telephone: [phone]‑510
Fax: [phone]‑101
E-mail: [email protected]
Internet: http://www.woodward.com
© 2021 Woodward GmbH. All rights reserved.
2 easYgen-3000XT Series 37595

Brief Overview
NOTICE!
This option manual must be used together with the device standard manual. An option
manual only describes the additional functionality of the device.
Please use the suitable standard manual to install, commission and operate the device:
• easYgen-3100/3200XT-P1 manual (37574)•
• easYgen-3400/3500XT-P1 manual (37580)•
• easYgen-3400/3500XT-P2 manual (37581)•
The easYgen-3000XT series are control units for engine-generator system management
applications.
The control units can be used in applications such as: co-generation, stand-by, AMF, peak
shaving, import/export or distributed generation.
The easYgen-3000XT series is also applicable for islanded, island parallel, mains parallel
and multiple unit mains parallel operations.
3easYgen-3000XT Series37595
Brief Overview

Sample application setup
Fig. 1: Sample application setup
A typical application mode for the control unit is the use for mains parallel operation
application.
• In this case, the easYgens-XT will function as an engine control with generator,•
mains and engine protection.
• The control unit can open and close the generator circuit breaker (GCB), group•
generator breaker (GGB), and the mains circuit breaker (MCB).
• The easYgens-XT are well prepared for system control and management, "talking"•
with other easYgens-3100XT/3200XT, easYgens-3400XT/3500XT and/or LS-5s and/or
Group Controller (GC).
4 easYgen-3000XT Series 37595
Brief Overview

Note: Unless otherwise noted, ”LS-5“, ”LSx“, ”LS -6XT“ and ”easYgen|LS-6XT“ are used
interchangeably in this document.
For a listing of all available application modes please refer to the "Chapter: Application
Field" in easYgen-3000XT manual.
Additional functionality
The easYgen-3000XT Rental controllers have some additional functions compared to the
'standard' easYgen-3000XT controllers. The di󰍒erences are listed below.
• Switchable Parameter Sets•
Refer to
╚═▷ “2.1.1 Switchable Parameter Sets” for details.
• Mobile Systems•
Refer to
╚═▷ “2.1.2 Mobile Systems” for details.
• Display Screen selection•
Refer to
╚═▷ “2.1.3 Display Screen Selection” for details.
•Second positive kWh counter •
Refer to
╚═▷ “2.1.4 Second Positive kWh Counter” for details.
5easYgen-3000XT Series37595
Brief Overview

Table of Contents
1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8█
1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8█
1.1.1 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8█
1.2 Depiction Of Notes And Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8█
1.2.1 Copyright And Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9█
1.2.2 Service And Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10█
1.3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10█
1.3.1 Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11█
1.3.2 General Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12█
1.3.3 Protective Equipment And Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15█
1.3.4 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15█
2 Additional Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16█
2.1 Con󰍓guration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16█
2.1.1 Switchable Parameter Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16█
2.1.2 Mobile Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37█
2.1.3 Display Screen Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42█
2.1.4 Second Positive kWh Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43█
3 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45█
3.1 LogicsManager Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45█
3.1.1 Logical Command Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45█
3.1.1.1 Group 04: Application conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45█
3.1.1.2 Group 87: LM Results 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45█
3.1.2 Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46█
3.2 AnalogManager Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46█
3.2.1 Data Sources AM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46█
3.2.1.1 Group 03: Busbar 1 values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46█
3.3 Status AND Event Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47█
3.3.1 Status messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47█
3.3.2 Event Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47█
6 easYgen-3000XT Series 37595
Table of Contents

4 List Of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48█
7easYgen-3000XT Series37595
Table of Contents

1 General Information
1.1 About This Manual
1.1.1 Revision History
Rev. Date Editor Changes in chronological descending order
A 2021-08 AS Option Manual - 1st issue
• Describing device software release 2.12-1•
1.2 Depiction Of Notes And Instructions
Safety instructions
Safety instructions are marked with symbols in these instructions. The safety instructions
are always introduced by signal words that express the extent of the danger.
DANGER!
This combination of symbol and signal word indicates an immediately-dangerous
situation that could cause death or severe injuries if not avoided.
WARNING!
This combination of symbol and signal word indicates a possibly-dangerous situation that
could cause death or severe injuries if it is not avoided.
CAUTION!
This combination of symbol and signal word indicates a possibly-dangerous situation that
could cause slight injuries if it is not avoided.
NOTICE!
This combination of symbol and signal word indicates a possibly-dangerous situation that
could cause property and environmental damage if it is not avoided.
8 easYgen-3000XT Series 37595
1 General Information
1.1 About This Manual

Tips and recommendations
This symbol indicates useful tips and recommendations as well as information for
e󰍕cient and trouble-free operation.
Additional markings
To emphasize instructions, results, lists, references, and other elements, the following
markings are used in these instructions:
Marking Explanation
⚙Start of a procedure list
>Prerequisite for a procedure list
▷Step-by-step instructions
▶Results of action steps
╚═▷ References to sections of these instructions and to other relevant
documents
• Listing without 󰍓xed sequence
☼ Example
»Buttons« Operating elements (e.g. buttons, switches), display elements (e.g.
signal lamps)
»Display« Screen elements (e.g. buttons, programming of function keys)
[Screen xx / Screen xy / Screen
xz] ...
Menu path.
The following information and setting refer to a page on HMI screen or
ToolKit located as described here.
Some parameters/settings/screens are available only either in ToolKit or
in HMI/display.
Dimensions in Figures
All dimensions shown with no units speci󰍓ed are in mm.
1.2.1 Copyright And Disclaimer
Disclaimer
All information and instructions in this manual have been provided under due
consideration of applicable guidelines and regulations, the current and known state of the
art, as well as our many years of in-house experience. Woodward assumes no liability for
any damages due to:
• Failure to comply with the instructions in this manual•
• Improper use / misuse•
• Willful operation by non-authorized persons•
• Unauthorized conversions or non-approved technical modi󰍓cations•
9easYgen-3000XT Series37595
1 General Information
1.2.1 Copyright And Disclaimer

• Use of non-approved spare parts•
The originator is solely liable for the full extent for damages caused by such conduct. The
obligations agreed-upon in the delivery contract, the general terms and conditions, the
manufacturer’s delivery conditions, and the statutory regulations valid at the time the
contract was concluded, apply.
Copyright
This manual is protected by copyright. No part of this manual may be reproduced in any
form or incorporated into any information retrieval system without written permission of
Woodward GmbH.
Delivery of this manual to third parties, duplication in any form - including excerpts - as
well as exploitation and/or communication of the content, are not permitted without a
written declaration of release by Woodward GmbH.
Actions to the contrary will entitle us to claim compensation for damages. We expressly
reserve the right to raise any further accessory claims.
1.2.2 Service And Warranty
Our Customer Service is available for technical information.
For regional support, please refer to: ══▷ http://www.woodward.com/Support_pgd.aspx.
In addition, our employees are constantly interested in new information and experiences
that arise from usage and could be valuable for the improvement of our products.
Warranty terms
Please enquire about the terms of warranty from your nearest Woodward representative.
For our contact search webpage please go to: ══▷ http://www.woodward.com/
Directory.aspx
1.3 Safety
NOTICE!
Damage due to improper use!
Improper use of the device may cause damage to the device as well as connected
components.
Improper use includes, but is not limited to:
•Storage, transport, and operation outside the speci󰍓ed conditions. •
10 easYgen-3000XT Series 37595
1 General Information
1.2.2 Service And Warranty

1.3.1 Personnel
WARNING!
Hazards due to insu󰈢ciently quali󰈠ed personnel!
If unquali󰍓ed personnel perform work on or with the control unit hazards may arise which
can cause serious injury and substantial damage to property.
• Therefore, all work must only be carried out by appropriately quali󰍓ed personnel.•
This manual speci󰍓es the personnel quali󰍓cations required for the di󰍒erent areas of work,
listed below:
Personnel:
•Quali󰍏ed electrician•
The quali󰍓ed electrician is able to execute tasks on electrical equipment and
independently detect and avoid any possible dangers due to his training, expertise
and experience, as well as knowledge of all applicable regulations.
The quali󰍓ed electrician has been specially trained for the work environment in
which he is active and is familiar with all relevant standards and regulations.
•User •
The user operates the device within the limits of its intended use, without additional
previous knowledge but according to the instructions and safety notes in this
manual.
The workforce must only consist of persons who can be expected to carry out their work
reliably. Persons with impaired reactions due to, for example, the consumption of drugs,
alcohol, or medication are prohibited.
When selecting personnel, the age-related and occupation-related regulations governing
the usage location must be observed.
11easYgen-3000XT Series37595
1 General Information
1.3.1 Personnel

1.3.2 General Safety Notes
Electrical hazards
DANGER!
Life-threatening hazard from electric shock!
There is an imminent life-threatening hazard from electric shocks from live parts.
Damage to insulation or to speci󰍓c components can pose a life-threatening hazard.
• Only a quali󰍓ed electrician should perform work on the electrical equipment.•
• Immediately switch o󰍒 the power supply and have it repaired if there is damage to•
the insulation.
• Before beginning work at live parts of electrical systems and resources, cut the•
electricity and ensure it remains o󰍒 for the duration of the work. Comply with the
󰍓ve safety rules in the process:
◦ cut electricity;◦
◦ safeguard against restart;◦
◦ ensure electricity is not 󰍔owing;◦
◦ earth and short-circuit; and◦
◦ cover or shield neighboring live parts.◦
• Never bypass a fuse or render it inoperable. Always use the correct amperage when•
changing a fuse.
• Keep moisture away from live parts. Moisture can cause short circuits.•
Prime mover safety
WARNING!
Hazards due to insu󰈢cient prime mover protection
The engine, turbine, or other type of prime mover should be equipped with an overspeed
(over-temperature, or over-pressure, where applicable) shutdown device(s), that
operates totally independently of the prime mover control device(s) to protect against
runaway or damage to the engine, turbine, or other type of prime mover with possible
personal injury or loss of life should the mechanical-hydraulic governor(s) or electric
control(s), the actuator(s), fuel control(s), the driving mechanism(s), the linkage(s), or
the controlled device(s) fail.
Device implemented self test
this Woodward device has a self test check implemented. Permanently under control are:
•processor function and •
• supply voltage.•
The internal signal "self check" is aligned in series with the inverse signal »Ready for op.
OFF« parameter 12580. Per default (factory settings) discrete output R01 is energized/
closed if device itself is OK.
12 easYgen-3000XT Series 37595
1 General Information
1.3.2 General Safety Notes

LogicsManager (LM) equation parameter 12580 allows to customize this safety relay. You
can use the result of this equation: LM command variable 99.01 .
Be careful in changing safety relevant settings!
Modi󰈠cations
WARNING!
Hazards due to unauthorized modi󰈠cations
Any unauthorized modi󰍓cations to or use of this equipment outside its speci󰍓ed
mechanical, electrical, or other operating limits may cause personal injury and/or
property damage, including damage to the equipment.
Any unauthorized modi󰍓cations:
•constitute "misuse" and/or "negligence" within the meaning of the product warranty •
thereby excluding warranty coverage for any resulting damage
•invalidate product certi󰍓cations or listings. •
Use of batteries/alternators
NOTICE!
Damage to the control system due to improper handling
Disconnecting a battery from a control system that uses an alternator or battery-
charging device whilst the charging device is still connected causes damage to the
control system.
• Make sure the charging device is turned o󰍒 before disconnecting the battery from•
the system.
Unit includes a lithium backup battery for Real Time Clock. Field replacement of the
battery is not allowed.
In case of battery replacement please contact your Woodward service partner.
Electrostatic discharge
Before working with terminals please read the following instructions.
⚙
Preventing electrostatic discharge damage (ESD)
ᐳ
•Protective equipment: ESD wrist band
13easYgen-3000XT Series37595
1 General Information
1.3.2 General Safety Notes

NOTICE!
Damage from electrostatic discharge
• All electronic equipment sensitive to damage from electrostatic•
discharge, which can cause the control unit to malfunction or fail.
• To protect electronic components from static damage, take the•
precautions listed below.
1. ▷
Avoid build-up of static electricity on your body by not wearing clothing made of
synthetic materials. Wear cotton or cotton-blend materials as much as possible because
these do not store static electric charges as easily as synthetics.
2. ▷
Before working on terminals on the control unit, ground yourself by touching
and holding a grounded metal object (pipes, cabinets, equipment, etc.) to
discharge any static electricity.
Alternatively wear an ESD wrist band connected to ground.
3. ▷
Before any maintenance work on the control unit, ground yourself by
touching and holding a grounded metal object (pipes, cabinets, equipment,
etc.) to discharge any static electricity.
Alternatively wear an ESD wrist band connected to ground.
4. ▷
Keep plastic, vinyl, and Styrofoam materials (such as plastic or Styrofoam cups,
cigarette packages, cellophane wrappers, vinyl books or folders, plastic bottles, etc.)
away from the control unit, modules and work area.
5. ▷
Opening the control cover may void the unit warranty. Do not remove the printed circuit
board (PCB) from the control cabinet unless instructed by this manual.
If instructed by this manual to remove the PCB from the control cabinet,
follow these precautions:
• Ensure that the device is completely voltage-free (all connectors have•
to be disconnected).
• Do not touch any part of the PCB except the edges.•
• Do not touch the electrical conductors, connectors, or components with•
conductive devices or with bare hands.
• When replacing a PCB, keep the new PCB in the plastic antistatic•
protective bag it comes in until you are ready to install it. Immediately
after removing the old PCB from the control cabinet, place it in the
antistatic protective bag.
For additional information on how to prevent damage to electronic components caused
by improper handling, read and observe the precautions in:
• "Woodward manual 82715, Guide for Handling and Protection of Electronic Controls,•
Printed Circuit Boards, and Modules".
14 easYgen-3000XT Series 37595
1 General Information
1.3.2 General Safety Notes

1.3.3 Protective Equipment And Tools
Protective gear
Personal protective equipment serves to protect risks to the safety and health of persons
as well as to protect delicate components during work.
Certain tasks presented in this manual require the personnel to wear protective
equipment. Speci󰍓c required equipment is listed in each individual set of instructions.
The cumulative required personal protective equipment is detailed below:
Protective equipment: ESD wrist band
The ESD (electrostatic discharge) wrist band keeps the user's body set to ground
potential. This measure protects sensitive electronic components from damage due to
electrostatic discharge.
Tools
Use of the proper tools ensures successful and safe execution of tasks presented in this
manual.
Speci󰍓c required tools are listed in each individual set of instructions.
The cumulative required tools are detailed below:
1.3.4 Intended Use
The genset control unit has been designed and constructed solely for the intended use
described in this manual.
The easYgen-... devices are available in two di󰍒erent enclosures. They are designed to be
installed either on the back plate of a switch gear cabinet (e.g. easYgen-x100.../...-
x400...) or on the front plate of a switch gear panel (e.g. easYgen-x200.../...-x500...).The
terminals are always located on the inner side of the housing.
The genset control unit must be used exclusively for engine-generator system management
applications.
• Intended use requires operation of the control unit within the speci󰍓cations listed in the "Technical•
Data".
• All permissible applications are outlined in the "Application Modes".•
• Intended use also includes compliance with all instructions and safety notes presented in this manual.•
• Any use which exceeds or di󰍒ers from the intended use shall be considered improper use!•
• No claims of any kind for damage will be entertained if such claims result from improper use.•
15easYgen-3000XT Series37595
1 General Information
1.3.3 Protective Equipment And Tools

2 Additional Functionality
General notes
This chapter describes the additional functionality only: this option device compared to
the standard device of the product series.
2.1 Con󰍏guration
2.1.1 Switchable Parameter Sets
General notes
Fig. 2: Switchable parameter sets - external switch
The easYgen with rental functionality provides four switchable parameter sets. This allows
to con󰍓gure and store four independent device settings packages.
16 easYgen-3000XT Series 37595
2 Additional Functionality

Default Settings
The easYgen rental version from factory comes with Set 1 values and settings instead of
easYgen standard settings (later on namend "Original").
These settings can be easily switched between 4 Sets by using one of the the following
access methods:
• External switch (╚═▷ Fig. 2)•
• Access via the front panel (HMI or Remote Panel)•
• External access with a PC using the ToolKit con󰍓guration software•
If the switchable parameter set is triggered the logical command variable "87.63",
"87.64" or "87.65" will be enabled.
The following overview (╚═▷ Table 1) shows the parameter sets in detail.
The column "Original" in the table below shows the original parameter of the standard
device. This parameter is still present as visualization value in the controller but not
used. The device functions are controlled by the parameters of the selected Set 1, 2, 3,
or 4.
Parameter ID
Set 1 Set 2 Set 3 Set 4 Original
System rated frequency ╚═▷
7462
╚═▷
7463
╚═▷
7464
╚═▷
7465
1750
Engine rated speed ╚═▷
4751
╚═▷
4772
╚═▷
4793
╚═▷
4814
1601
Generator rated voltage ╚═▷
4752
╚═▷
4773
╚═▷
4794
╚═▷
4815
1766
Mains rated voltage ╚═▷
4754
╚═▷
4775
╚═▷
4796
╚═▷
4817
1768
Busbar 1 rated voltage ╚═▷
4831
╚═▷
4833
╚═▷
4835
╚═▷
4837
1781
Gen. rated active power
[kW]
╚═▷
4756
╚═▷
4777
╚═▷
4798
╚═▷
4819
1752
Gen. rated react. power
[kvar]
╚═▷
4758
╚═▷
4779
╚═▷
4800
╚═▷
4821
1758
Generator rated current ╚═▷
4760
╚═▷
4781
╚═▷
4802
╚═▷
4823
1754
Generator voltage
measuring
╚═▷
7980
╚═▷
7985
╚═▷
7990
╚═▷
7995
1851
17easYgen-3000XT Series37595
2 Additional Functionality
2.1.1 Switchable Parameter Sets

Parameter ID
Set 1 Set 2 Set 3 Set 4 Original
Mains voltage measuring ╚═▷
7981
╚═▷
7986
╚═▷
7991
╚═▷
7996
1853
Busbar 1 voltage measuring ╚═▷
7982
╚═▷
7987
╚═▷
7992
╚═▷
7997
1856
Int. freq. control setpoint 1 ╚═▷
4762
╚═▷
4783
╚═▷
4804
╚═▷
4825
5500
Int.voltage control setpoint 1 ╚═▷
4763
╚═▷
4784
╚═▷
4805
╚═▷
4826
5600
Int. load control setpoint 1 ╚═▷
4765
╚═▷
4786
╚═▷
4807
╚═▷
4828
5520
Load setpoint 1 ╚═▷
7450
╚═▷
7451
╚═▷
7452
╚═▷
7453
5526
PF/kvar setpoint 1 mode ╚═▷
7983
╚═▷
7988
╚═▷
7993
╚═▷
7998
5743
Int. power factor setpoint 1 ╚═▷
4767
╚═▷
4788
╚═▷
4809
╚═▷
4830
5620
Int. kvar setpoint 1 ╚═▷
7984
╚═▷
7989
╚═▷
7994
╚═▷
7999
5745
Application mode ╚═▷
7454
╚═▷
7455
╚═▷
7456
╚═▷
7457
3444
Breaker transition mode ╚═▷
7458
╚═▷
7459
╚═▷
7460
╚═▷
7461
3411
Table 1: Parameter Sets
18 easYgen-3000XT Series 37595
2 Additional Functionality
2.1.1 Switchable Parameter Sets

Fig. 3: Toolkit - Switchable parameter sets
Dependencies
Fig. 4: AC power triangle
PF Power Factor
P Active Power [kW]
S Apparent power [kVA]
Q Reactive Power [kvar]
The AC power triangle illustrates the dependencies between active power, apparent
power, reactive power and power factor.
19easYgen-3000XT Series37595
2 Additional Functionality
2.1.1 Switchable Parameter Sets

• PF = P/S = cos Φ•
• Q = √(S2-P2)•
•S = √(P2+Q2) •
• P = S * PF•
ID Parameter CL Setting range
[Default]
Description
7462
7463
7464
7465
System rated
frequency
2 50 / 60 Hz
7462: [50 Hz]
7463: [60 Hz]
7464: [50 Hz]
7465: [60 Hz]
The rated frequency of the
system is used as a
reference 󰍓gure for all
frequency related
functions, which use a
percentage value, like
frequency monitoring,
breaker operation windows
or the Analog Manager.
Notes
Original parameter 1750 is
still present as visualization
value in the controller.
4751
4772
4793
4814
Engine rated
speed
2 500 to 4,000 rpm
4751: [1,500 rpm]
4772: [1,800 rpm]
4793: [1,500 rpm]
4814: [1,800 rpm]
Number of revolutions per
minute of the engine at
rated engine speed. The
speed control with an ECU
via J1939 CAN bus refers to
this value.
Notes
Original parameter 1601 is
still present as visualization
value in the controller.
4752
4773
4794
4815
Generator rated
voltage
2 50 to 650000 V
4752: [400 V]
4773: [240 V]
4794: [200 V]
4815: [200 V]
This value refers to the
rated voltage of the
generator (generator
voltage on data plate) and
is the voltage measured on
the potential transformer
primary.
The generator potential
transformer primary
voltage is entered in this
parameter.
The generator rated
voltage is used as a
20 easYgen-3000XT Series 37595
2 Additional Functionality
2.1.1 Switchable Parameter Sets