World Market Palmera 585019 User manual

Assembly Instructions
Page 1
PALMERA RECTANGLE BENCH
SKU–585019
NOT FOR COMMERCIAL USE.
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877- 967-5362 FOR ASSISTANCE.

Page 2
H-2 4
A
B
Bench Top
Leg
1
H-1 2
H-3
H-4
H-5
H-6
H-7
2
LABEL PICTURE DESCRIPTION QTY
Component List
LABEL PICTURE DESCRIPTION QTY
Hardware
12
C1
D
2
8
8
Upper Wood Support Bar 2
Spring Washer M8
11.5 mm x 1.2 mm
16 mm x 1.7 mm
Flat Washer M8
Lower Wood Crossbar
2
Allen Key(L=110MM)
H-81
Short Allen Bolt
M6x25mm
Medium Allen Bolt
M8x70mm
Barrel Nut M8
Long Allen Bolt
M8x 90mm
Spare Allen Bolt
(used temporarily)
H-9 2
13 mm x 1 mm
Flat Washer M6

Page 3
Before Beginning:
Assembly Preparation
Unpack all hardware bags and components to ensure you have all parts-
Read instructions, cover to cover-
Have 2 adults on hand for assembly-
Do not assemble on flooring or carpet-
Assemble on a clean non-marring surface (packing foam)-
Save all packaging until finished-
In case of missing parts, please contact nearest Cost Plus World Market
store or our customer service call center 877-967-5362.

Page 4
Step 1
Assembly Steps
Step 2
.
Step 1
(H-1) Short Allen Bolt
A
D
D
(H-1)
x 2
90%
Allen key
(H-7)
(H-2) Medium Allen Bolt
Allen key
(H-7)
(H-3) Barrel Nut
(H-8) Spare Allen Bolt
B
B
C
x 2
(H-2)
(H-7) (H-3)
(H-8)
90%
IMPORTANT: It is highly recommended to have a second person to assist during this product assembly.
Do not fully tighten allen bolts until all components are in place. Do not over tighten allen bolts.
Using a second person to assist you, place Bench Top (A) upside down onto a padded, non-marring surface.
over the metal frame on the underside of Bench Top (A). Secure both Upper Wood Support Bars (D)
Next, position both Upper Wood Support Bars (D) as shown, making sure the notches at the ends of both bars attach
using Short Allen Bolts (H-1) and Flat Washers (H-9).
TOP
TOP
HINT: Thread spare Allen Bolt (H-8) into the
end of Barrel Nut (H-3) to keep the barrel thread aligned.
Remove the spare Allen Bolt (H-8) when you're done.
(used temporarily)
.
Arrange both Legs (B) with the tops facing downwards as shown. Attach Lower Wood Crossbar (C) to Legs (B)
and secure both sides by attaching a Medium Allen Bolt (H-2) and Flat Washers (H-6) into a Barrel Nut (H-3).
Use Spare Allen Bolt (H-8) threaded into Barrel Nut (H-3) to hold the threads aligned while engaging
Medium Allen Bolt (H-2). Engage Medium Allen Bolts (H-2) using Allen Key (H-7)
but do not fully tighten them yet. Once Barrel Nuts (H-3) have been engaged, remove the spare Allen Bolt (H-8).
(H-9) Flat Washer M6 (H-9)
Engage the bolts usingAllen Key (H-7) but do not fully tighten them yet.
(H-6) Flat Washer
(H-6)

Step 3
Assembly Steps
Page 5
(H-4) Long Allen Bolt
Allen key
(H-7)
(H-5) Spring Washer M8
(H-6) Flat Washer
x 4
(H-7)
(H-7)
(H-6)
(H-6)
(H-5)
(H-4)
(H-4)
B
B
A
90%
Step 4
(H-2) Bolt M8 x 70mm
Allen key
(H-7)
C
100%
(H-2)
(H-7) (H-7)
D
D
TOP
IMPORTANT: It is highly recommended to have a second person to assist during this assembly step.
Using a second person to assist you, carefully lower the leg assembly (from Step 2) down onto the Bench Top (A)
assembly (from Step 1). Align the holes on Legs (B) with the metal apron frame on Bench Top (A) and secure each leg
to the frame using 2 Long Allen Bolts (H-4), Spring Washers (H-5) and Flat Washers (H-6). Engage the bolts using
Allen Key (H-7) but do not fully tighten them yet.
TOP
Secure both Upper Wood Support Bars (D) to Lower Wood Crossbar (C) using Medium Allen Bolts (H-2)
and Flat Washers (H-6). Engage the bolts and then FULLY TIGHTEN them using Allen Key (H-7).
(H-6)
(H-6) Flat Washer

Step 5
Assembly Steps
.
Step 6
Page 6
100%
100%
.
Allen key
(H-7)
Allen key
(H-7)
TOP
FULLY TIGHTEN all Allen Bolts from Steps 1-4 at this time using Allen Key (H-7).
TOP
NOTE: Bench Top (A) comes with a pre-installed metal frame. Ensure that all pre-installed bolts (12pcs total)
securing the metal frame are FULLY TIGHTENED using Allen Key (H-7).

Step 7
Assembly Steps
.
Page 7
IMPORTANT: It is highly recommended to have a second person to assist during this assembly step.
TOP
Using a second person to assist you, carefully turn the bench assembly upright. Position the table in its desired location
before making any final adjustments using the adjustable floor levelers (if needed). Assembly is now complete and
the bench is ready for use.
NOTE: Check that all bolts are fully tightened every 3 months to ensure stability.

•
• Do not place furniture near heating or cooling vents.
• Do not write on furniture without a padded barrier to protect the surface.
• Not for commercial use. For residential use only.
• Dust and pick-up spills using a clean, non-colored, lint-free cloth.
• Stains may be removed with mild soap solution and damp cloth.
Care & Maintenance
• Do not put hot items directly on furniture surface.
• Do not clean furniture with harsh cleansers or polish.
Page 8
•
• Store furniture or use an appropriate furniture cover during cold or inclement weather.
CAUTION: As with any wood, the color may fade if left in direct sunlight of inclement weather. Minor cracking may
occur with age. These are naturally occurring features of wood and do not affect product performance.
We recommend using our Natural Outdoor Wood Furniture Finish (sold separately) to help preserve and protect
the wood and finish. Do not apply any finish to the table top surface.