World Market Palmera 585020 User manual

Assembly Instructions
Page 1
SKU–585020
PALMERA RECTANGLE TABLE
NOT FOR COMMERCIAL USE.
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877- 967-5362 FOR ASSISTANCE.

Page 2
H-2 4
A
B
Table Top
Leg
1
H-1 3
H-3
H-4
H-5
H-6
H-7
2
LABEL PICTURE DESCRIPTION QTY
Component List
LABEL PICTURE DESCRIPTION QTY
Hardware
12
C1
Umbrella Hole Cap
D
1
2
8
8
Upper Wood Support Bar 2
E
Spring Washer M8
11.5 mm x 1.2 mm
16 mm x 1.7 mm
Flat Washer M8
Lower Wood Crossbar
2
Allen Key(L=110MM)
Barrel Nut M8
Short Allen Bolt
M6x65mm
Medium Allen Bolt
M8x80mm
Long Allen Bolt
M8x110mm
H-8 2
13 mm x 1 mm
Flat Washer M6

Page 3
Before Beginning:
Assembly Preparation
Unpack all hardware bags and components to ensure you have all parts-
Read instructions, cover to cover-
Have 2 adults on hand for assembly-
Do not assemble on flooring or carpet-
Assemble on a clean non-marring surface (packing foam)-
Save all packaging until finished-
In case of missing parts, please contact nearest Cost Plus World Market
store or our customer service call center 877-967-5362.

Page 4
Step 1
Assembly Steps
Using a second person to assist you, place Table Top (A) upside down onto a padded, non-marring surface.
Step 2
Step 1
(H-1) Short Allen Bolt
A
D
D
(H-1)
over the metal frame on the underside of Table Top (A). Secure both Upper Wood Support Bars (D) using
x 2
Next, position both Upper Wood Support Bars (D) as shown, making sure the notches at the ends of both bars attach
90%
Allen key
(H-7)
(H-2) Medium Allen Bolt
Allen key
(H-7)
(H-3) Barrel Nut
(H-1) Short Allen Bolt
B
B
C
x 2
(H-2)
(H-7) (H-3)
(H-1)
90%
IMPORTANT: It is highly recommended to have a second person to assist during this product assembly.
Do not fully tighten allen bolts until all components are in place. Do not over tighten allen bolts.
TOP
Short Allen Bolts (H-1) and Flat Washers (H-8). Engage the bolts using Allen Key (H-7)
HINT: Thread a spare Short Allen Bolt (H-1) into the
end of Barrel Nut (H-3) to keep the barrel thread aligned.
Remove the spare Short Allen Bolt (H-1) when you're done.
(used temporarily) TOP
Arrange both Legs (B) with the tops facing downwards as shown. Attach Lower Wood Crossbar (C) to Legs (B) and
secure both sides by attaching a Medium Allen Bolt (H-2) and Flat Washers (H-6) into a Barrel Nut (H-3).
Use a spare Short Allen Bolt (H-1) threaded into Barrel Nut (H-3) to hold the threads aligned while engaging Medium
Allen Bolt (H-2). Engage Medium Allen Bolts (H-2) using Allen Key (H-7) but do not fully tighten them yet.
Once Barrel Nuts (H-3) have been engaged, remove the spare Short Allen Bold (H-1).
(H-8)
(H-8) Flat Washer M6
but do not fully tighten them yet.
(H-6) Flat Washer
(H-6)

(H-4) Long Allen Bolt
Allen key
(H-7)
(H-5) Spring Washer M8
(H-6) Flat Washer
x 4
(H-7)
(H-7)
(H-6)
(H-6)
(H-5)
(H-4)
(H-4)
B
B
A
90%
Step 4
(H-2) Bolt M8 x 80mm
Allen key
(H-7)
C
100%
(H-2)
(H-7)
(H-7)
D
D
TOP
IMPORTANT: It is highly recommended to have a second person to assist during this assembly step.
Using a second person to assist you, carefully lower the leg assembly (from Step 2) down onto the Table Top (A)
assembly (from Step 1). Align the holes on Legs (B) with the metal apron frame on Table Top (A) and secure each leg
to the frame using 2 Long Allen Bolts (H-4), Spring Washers (H-5) and Flat Washers (H-6). Engage the bolts using
Allen Key (H-7) but do not fully tighten them yet.
TOP
Secure both Upper Wood Support Bars (D) to Lower Wood Crossbar (C) using Medium Allen Bolts (H-2)
and Flat Washers (H-6). Engage the bolts and then FULLY TIGHTEN them using Allen Key (H-7).
(H-6)
(H-6) Flat Washer
Step 3
Assembly Steps
Page 5

Step 5
Assembly Steps
.
Step 6
Page 6
100%
100%
.
Allen key
(H-7)
FULLY TIGHTEN all Allen Bolts from Steps 1-4 at this time using Allen Key (H-7).
Allen key
(H-7)
TOP
TOP
NOTE: Table Top (A) comes with a pre-installed metal frame. Ensure that all pre-installed bolts (12pcs total) securing
the metal frame are FULLY TIGHTENED using Allen Key (H-7).

Step 7
Assembly Steps
E
.
Umbrella Hole Cap
Page 7
TOP
IMPORTANT: It is highly recommended to have a second person to assist during this assembly step.
Using a second person to assist you, carefully turn the table assembly upright. Place Umbrella Hole Cap (E) into
the umbrella hole at the middle of the table. Position the table in its desired location before making any final
adjustments using the adjustable floor levelers (if needed). Assembly is now complete and the table is ready for use.
NOTE: Check that all bolts are fully tightened every 3 months to ensure stability.

•
• Do not place furniture near heating or cooling vents.
• Do not write on furniture without a padded barrier to protect the surface.
• Not for commercial use. For residential use only.
• Dust and pick-up spills using a clean, non-colored, lint-free cloth.
• Stains may be removed with mild soap solution and damp cloth.
Care & Maintenance
• Do not put hot items directly on furniture surface.
• Do not clean furniture with harsh cleansers or polish.
Page 8
•
• Store furniture or use an appropriate furniture cover during cold or inclement weather.
CAUTION: As with any wood, the color may fade if left in direct sunlight of inclement weather. Minor cracking may
occur with age. These are naturally occurring features of wood and do not affect product performance.
We recommend using our Natural Outdoor Wood Furniture Finish (sold separately) to help preserve and protect
the wood and finish. Do not apply any finish to the table top surface.