Worx WG286E Installation manual

40V Cordless Hedge Trimmer
WG286E WG286E.X
SAFETY AND OPERATING MANUAL
ORIGINAL INSTRUCTIONS

2
40V Cordless Hedge Trimmer
WG286E WG286E.X
TABLE OF CONTENTS
1. PRODUCT SAFETY
2. COMPONENT LIST
3. TECHNICAL DATA
4. INTENDED USE
5. OPERATING INSTRUCTIONS
6. HOW TO USE YOUR HEDGE TRIMMER
7. MAINTENANCE
8. ENVIRONMENTAL PROTECTION
9. DECLARATION OF CONFORMITY
1. PRODUCT SAFETY
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING Read all safety warnings,
instructions, illustrations and specications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, re and/or serious injury .
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk
of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the inuence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with
your nger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action
can cause severe injury within a fraction of a
second.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not

3
40V Cordless Hedge Trimmer
WG286E WG286E.X
turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe
handling and control of the tool in unexpected
situations.
5. Battery tool use and care
a) Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of re
when used with another battery pack .
b) Use power tools only with specically
designated battery packs. Use of any other
battery packs may create a risk of injury and re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modied. Damaged or modied
batteries may exhibit unpredictable behaviour
resulting in re, explosion or risk of injury.
f) Do not expose a battery pack or tool to re
or excessive temperature. Exposure to re or
temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instructions.
Charging improperly or at temperatures outside
the specied range may damage the battery and
increase the risk of re.
6. Service
a) Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed
by the manufacturer or authorized service
providers.
HEDGE TRIMMER SAFETY
WARNINGS
a) Keep all parts of the body away from the blade.
Do not remove cut material or hold material
to be cut when blades are moving. Blades
continue to move after the switch is turned off.
A moment of inattention while operating the
hedge trimmer may result in serious personal
injury .
b) Carry the hedge trimmer by the handle with the
blade stopped and taking care not to operate
any power switch. Proper carrying of the hedge
trimmer will decrease the risk of inadvertent
starting and resultant personal injury from the
blades .
c) When transporting or storing the hedge
trimmer, always t the blade cover. Proper
handling of the hedge trimmer will decrease the
risk of personal injury from the blades .
d) When clearing jammed material or servicing the
unit, make sure all power switches are off and
the battery back is removed or disconnected.
Unexpected actuation of the hedge trimmer
while clearing jammed material or servicing may
result in serious personal injury.
e) Hold the hedge trimmer by insulated gripping
surfaces only, because the blade may contact
hidden wiring. Blades contacting a “live” wire
may make exposed metal parts of the hedge
trimmer “live” and could give the operator an
electric shock.
f) Keep all power cords and cables away from
cutting area. Power cords or cables may
be hidden in hedges or bushes and can be

4
40V Cordless Hedge Trimmer
WG286E WG286E.X
accidentally cut by the blade.
g) Do not use the hedge trimmer in bad weather
conditions, especially when there is a risk
of lightning. This decreases the risk of being
struck by lightning.
h) Check the hedges and bushes for foreign
objects, e.g. wire fences and hidden wiring.
i) Hold the hedge trimmer properly, e.g. with both
hands if two handles are provided.
j) The hedge trimmer is intended to be used by
the operator at ground level and not on ladders
or any other unstable support.
k) Before operating the hedge trimmer, the user
should make sure the locking device(s) of any
moving elements (e.g. the extended shaft and
pivoting element), if any, are in the locked
position.
l) Have any adjustable stopping mechanism
maintained at regular intervals.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred cells or battery
pack.
b) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer
where they may short-circuit each other or be
short-circuited by conductive materials. When
battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that
can make a connection from one terminal to
another. Shorting the battery terminals together
may cause burns or a re.
c) Do not expose battery pack to heat or re.
Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical
shock.
e) In the event of battery leaking, do not allow
the liquid to come into contact with the skin
or eyes. If contact has been made, wash the
affected area with copious amounts of water
and seek medical advice.
f) Keep battery pack clean and dry.
g) Wipe the battery pack terminals with a clean
dry cloth if they become dirty.
h) Battery pack needs to be charged before use.
Always refer to this instruction and use the
correct charging procedure.
i) Do not maintain battery pack on charge when
not in use.
j) After extended periods of storage, it may
be necessary to charge and discharge the
battery pack several times to obtain maximum
performance.
k) Recharge only with the charger specied
by Worx. Do not use any charger other than
that specically provided for use with the
equipment.
l) Do not use any battery pack which is not
designed for use with the equipment.
m) Keep battery pack out of the reach of children.
n) Retain the original product literature for future
reference.
o) Remove the battery from the equipment when
not in use.
p) Dispose of properly.
q) Do not mix cells of different manufacture,
capacity, size or type within a device.
r) Keep the battery away from microwaves and
high pressure.
s) Warning! Do not use non-rechargeable
batteries.
SYMBOLS
To reduce the risk of injury, user must
read instruction manual
Warning
Wear ear protection
Wear eye protection
Wear dust mask
Do not expose to rain
Do not burn
Batteries may enter water cycle if
disposed improperly, which can
be hazardous for ecosystem. Do
not dispose of waste batteries as
unsorted municipal waste.

5
40V Cordless Hedge Trimmer
WG286E WG286E.X
Li-Ion battery This product has been
marked with a symbol relating to
‘separate collection’ for all battery
packs and battery pack. It will
then be recycled or dismantled in
order to reduce the impact on the
environment. Battery packs can be
hazardous for the environment and
for human health since they contain
hazardous substances.
Keep hands away from blade
Remove battery from the socket
before carrying out any adjustment,
servicing or maintenance.
Wear protective gloves.
Waste electrical products must not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authorities or
retailer for recycling advice.

6
40V Cordless Hedge Trimmer
WG286E WG286E.X
21
7654
10
9
11
3
8

7
40V Cordless Hedge Trimmer
WG286E WG286E.X
2
2
1
2
2
1
B1
B2
G
A
D
F
C1
C2
11
2
33
44
E
12
H
100%
0%

8
40V Cordless Hedge Trimmer
WG286E WG286E.X
2
2
1
2
2
1
B1
B2
G
A
D
F
C1
C2
11
2
33
44
E
12
H
100%
0%
0°
45°
90°
135°
180
I2
J2
I1
K
J1
L1

9
40V Cordless Hedge Trimmer
WG286E WG286E.X
0°
45°
90°
135°
180
I2
J2
I1
K
J1
L1
L2
N
M

10
40V Cordless Hedge Trimmer
WG286E WG286E.X
2. COMPONENT LIST
1. ROTATING REAR HANDLE
2. POWER INDICATOR LIGHT
3. BATTERY PACK*
4. FRONT HANDLE
5. OPERATOR PRESENCE SWITCH
(ALL AROUND SWITCH FUNCTION)
6. SAFETY GUARD
7. BLADE
8. BLADE SHEATH
9. LOCKING SWITCH FOR ROTATING
10. THROTTLE TRIGGER
11. HEDGE SWEEPER*
12. BATTERY PACK RELEASE BUTTON*
(See Fig. G)
* Not all the accessories illustrated or described
are included in standard delivery.
3. TECHNICAL DATA
Type WG286E WG286E.X (250-299- designation
of machinery, representative of cordless hedge
trimmer)
WG286E WG286E.X**
Voltage 40V MAX(2x20V MAX.)***
No-load speed 3400 /min
Blade length 61 cm
Cutting length 58 cm
Tooth spacing 33 mm
Max cutting diameter 27 mm
Machine Weight
(Bare Tool) 2.7 kg
** X=1-999, A-Z, M1-M9 there are only used for
different customers, there are no safe relevant
changes between these models
*** Voltage measured without workload. Initial
battery voltage reaches maximum of 20 volts.
Nominal voltage is 18 volts.
SUGGESTED BATTERIES
AND CHARGERS
Category Type Capacity
20V Battery WA3551 2.0 Ah
WA3639 2.0 Ah
20V Charger WA3772 2.0 A
WA3883 4.0 A
We recommend that you purchase your accessories
from the same store that sold you the tool. Refer to
the accessory packaging for further details. Store
personnel can assist you and offer advice.
NOISE INFORMATION
A weighted sound pressure LpA: 85.83 dB(A)
KpA= 3 dB(A)
A weighted sound power LwA: 96.83 dB(A)
KwA= 3 dB(A)
Wear ear protection
VIBRATION INFORMATION
Vibration total values (triax vector sum)
determined according to EN 62841:
Vibration emission value Rear: ah =1.79 m/s²
Front: ah =2.73 m/s²
Uncertainty K = 1.5m/s²
The declared vibration total value and the declared
noise emission value have been measured in
accordance with a standard test method and may
be used for comparing one tool with another.
The declared vibration total value and the declared
noise emission value may also be used in a
preliminary assessment of exposure.
WARNING: The vibration and noise
emissions during actual use of the power
tool can differ from the declared value depending
on the ways in which the tool is used especially
what kind of workpiece is processed dependant on
the following examples and other variations on how
the tool is used:
How the tool is used and the materials being cut or
drilled.

11
40V Cordless Hedge Trimmer
WG286E WG286E.X
The tool being in good condition and well
maintained.
The use of the correct accessory for the tool and
ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration and noise accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration syndrome
if its use is not adequately managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the
operating cycle such as the times when the tool is
switched off and when it is running idle but not
actually doing the job. This may signicantly reduce
the exposure level over the total working period.
Helping to minimise your vibration and noise
exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti
vibration and noise accessories.
Plan your work schedule to spread any high
vibration tool use across a number of days.
4. INTENDED USE
The machine is intended for cutting and trimming
hedges and bushes in domestic use.
5. OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
WARNING! Do not use the product without
attaching the guard and front handle.
ASSEMBLY & OPERATION
ACTION FIGURE
BEFORE USING YOUR CORDLESS
HEDGETRIMMER
Assembling the safety guard See Fig. A
Assembling the front handle
NOTE : The handle is designed to
prevent being assembled in wrong
direction . If you nd it cannot be
installed, please turn it around.
See Fig.
B1, B2
Assembling Hedge Sweeper
NOTE:To avoid clippings and other
debris to fall back into the hedge,
you can use the Hedge Sweeper to
sweep the cuttings off the hedge.
You can operate the machine with or
without Hedge Sweeper according to
different working conditions.
See Fig.
C1,C2
Checking the battery charge condition
NOTE : Fig. C only applies for the
battery pack with battery indicator
light.
See Fig. D
Charging the battery pack
NOTE :
• The batteries are shipped
uncharged. Each battery must be
fully charged before the rst use.
• Always fully charge the two
batteries at same time. More
details can be found in charger’s
manual.
See Fig. E
Installing and Removing the battery
pack
NOTE :
• This machine will only run when
2 batteries are installed. It is
recommended to use the same
two batteries and charge the two
batteries at the same time.
• When you use two batteries with
different power, the machine will
only run to the lower common
denominator.
See Fig. F
Power indicator light
See details in BATTERY STATUS part
IMPORTANT:
When only one light is illuminated,
your battery is overly discharged,
even though the trimmer may still
be capable of hedge trimming.
Continuing to operate your trimmer
with the battery in this discharged
condition may reduce the life and
performance of your battery.
When no light is illuminated, at least
one battery is not fully installed or
battery may be defective, please
double check the batteries are fully
seated into position.
See Fig. G

12
40V Cordless Hedge Trimmer
WG286E WG286E.X
OPERATION
Remove the blade sheath See Fig. H
Starting and stopping See Fig.
I1, I2
Rotating rear handle
NOTE :
• Unlock the locking switch before
rotating.
• After rotating the handle to the
desired position, adjust it a little
until a click can be heard.
WARNING:
• Always make sure that the handle
is locked in the desired position
before operation.
• Always make sure the locking
switch is locked before starting
the hedge trimmer.
See Fig.
J1, J2
Top cutting
WARNING: If any parts are
missing, damaged or broken,
do not operate your hedge trimmer
until all damaged parts have been
replaced or repaired. Failure to do
so could result in serious personal
injury. DO NOT USE WITHOUT FRONT
HANDLE AND SAFETY GUARD.
See Fig. K
Side cutting
WARNING: Stop operating the trim-
mer before rotating the handle.
See Fig.
L1, L2
Lubricating the Cutting Blade
Remove the battery pack from the
trimmer.
Place the trimmer on a level surface.
Apply some lubrication oil along the
edge of the blade.
It is recommended to oil the machine
after using your hedge trimmer for an
extended period.
WARNING: Do not oil the blade when
the trimmer is running.
See Fig. M
6. HOW TO USE YOUR HEDGE
TRIMMER
Before cutting an area, inspect it rst and remove
any foreign objects that could become thrown or
entangled in the blades. Always hold the trimmer
with both hands and with the blade away from you
before turning it on.
When trimming new growth, use a wide sweeping
action so that the stems are fed directly into the
blade.
Allow the cutting blades to reach full speed before
cutting. When operating, keep the cutting blades
away from people and objects such as walls, large
stones, trees, vehicles, etc.
If the blade stalls, immediately stop the trimmer.
Release the Operator Presence Switch and
Throttle Trigger before attempting to clear jammed
debris from the cutting blades.
Wear gloves when trimming thorny or prickly
growth.
Do not attempt to cut stems that are too thick for
the cutting blade.
Top cutting
Use a wide sweeping motion. A slight downward tilt
of the cutting blades in the direction of motion gives
the best cutting results.
Side cutting
When trimming the sides of the hedge, begin at the
bottom and cut upwards, tapering the hedge inward
at the top. This shape will expose more of the
hedge, resulting in a more uniformed growth
BATTERY STATUS (See Fig. G)
• Before starting or after use, press the button
beside the power indicator light on the machine
to check the battery capacity.
• During operation, the battery capacity will be
indicated automatically by the battery power
indicator. The indicator constantly senses and
displays the battery condition as follows.
• For the machine with 2 battery packs with
different power, the power indicator light
displays the battery condition with the lower one
of the two batteries.
Battery indicator light
status Battery condition
Five green lights
( ) are
illuminated.
The two batteries are in a
highly charged condition.
Two, three or four
green lights are
illuminated.
The two batteries have a
remaining charge. The more
lights are illuminated, the
more battery capacity.
Only one green
light ( ) is
illuminated.
At least one battery is almost
depleted and needs to be
charged.
No light is illuminated.
At least one battery is not
fully installed or battery may
be defective.

13
40V Cordless Hedge Trimmer
WG286E WG286E.X
Only one light is
ashing twice per
cycle.
At least one battery is over
discharged (please refer to
the battery charge condition),
please recharge the two
batteries at once before use
again or storage.
Only one light is
ashing three times
per cycle.
At least one battery is hot,
wait for them cool down
before start again.
Only one light is
ashing four times per
cycle.
The machine is over load.
Remove tool from cutting
area and try again.
7. MAINTENANCE
Remove the battery from Hedge trimmer before
carrying out any adjustment, servicing or
maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls
free of dust.
8. ENVIRONMENTAL
PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0°C-45°C.
The recommended ambient temperature range for
the charging system during charging is 0°C-40°C.
9. DECLARATION OF
CONFORMITY
We,
Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
On behalf of Positec declare that the product
Description Worx Cordless Hedge Trimmer
Type WG286E WG286E.X (250-299- designation
of machinery, representative of cordless hedge
trimmer)
Function Trimming hedges and brushes
Complies with the following directives,
2006/42/EC
2014/30/EU
2011/65/EU&(EU)2015/863
2000/14/EC amended by 2005/88/EC
2000/14/EC amended by 2005/88/EC:
- Conformity assessment procedure as per Annex V
- Measured sound power level 96.83 dB (A )
- Declared guaranteed sound power level 100 dB(A)
Standards conform to,
EN 62841-1
EN 62841-4-2
EN ISO 3744
EN IEC 55014-1
EN IEC 55014-2
The person authorized to compile the technical le,
Name Marcel Filz
Address Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
2023/03/23
Allen Ding
Deputy Chief Engineer, Testing & Certication
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China

14
40V Cordless Hedge Trimmer
WG286E WG286E.X
DECLARATION OF
CONFORMITY
We,
Positec (UK & Ireland) Ltd,
PO Box 6242, Newbury, RG14 9LT, UK
On behalf of Positec declare that the product
Description Battery-powered Hedge Trimmer
Type WG286E WG286E.X (250-299- designation
of machinery, representative of cordless hedge
trimmer)
Function Trimming hedges and brushes
Complies with the following regulations:
Supply of Machinery (Safety) Regulations 2008
Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment
Regulations
Noise Emission in the Environment by Equipment for
Use Outdoors Regulations
Conformity assessment procedure as per
SCHEDULE 8
Measured Sound Power Level 96.83 dB(A)
Declared Guaranteed Sound Power Level 100 dB(A)
Standards conform to,
BS EN 62841-1
BS EN 62841-4-2
BS EN ISO 3744
BS EN IEC 55014-1
BS EN IEC 55014-2
The person authorized to compile the technical le,
Name: Jim Kirkwood
Address Positec (UK & Ireland) Ltd,
PO Box 6242, Newbury, RG14 9LT, UK
2023/03/23
Allen Ding
Deputy Chief Engineer, Testing & Certication
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China

Copyright © 2023, Positec. All Rights Reserved.
AR01707800
www.worx.com