X-Vision XIP3101 User manual

Model:
XIP3101
Wireless IP Camerawith IR Night
Vision & 3G Mobile Phone Access
IP CCTV
Quick Installation Guide

1 Getting Started
Package Contents
Check the items contained in the package carefully. You should have
the following:
lOne Wireless IP CCTV Camera.
lOne AC Power Adapter.
lOne External Antenna.
lOne Camera Bracket.
lOne Ethernet Cable (RJ-45 type).
lOne Installation CD-ROM.
lOne Quick Installation Guide.
NOTE If any item is damaged or missing, contact your local distributor.
- 1 -

System Requirement
Networking
LAN: 10Base-T Ethernet or 100Base-TX Fast Ethernet.
WLAN: IEEE 802.11b/g (Model XIP3001 only).
Configuring the Camera:
CPU: Pentium 3, 350MHz or above
Memory Size: 128MB or above
Resolution: 800 x 600 or above
Browser: Internet Explorer 6.0 or above
Operating Systems: Windows 2000/XP/Vista
Viewing the Camera:
CPU: Pentium 3, 350MHz or above
Memory Size: 128MB or above
Resolution: 800 x 600 or above
Browser: Internet Explorer 6.0 or above, Apple Safari 2.0 or Mozilla
Firefox
Operating Systems: Windows 2000/XP/Vista, Apple OSX
*Please note audio is not available when using Safari or Firefox
Accessing the camera using Xview Recording & Viewing Software
Resolution: 1024 x 768 or above
Operating Systems: Windows 2000/XP/Vista
NOTE If you connect multiple cameras to monitor various places
simultaneously, you are recommended to use a computer with
higher performance.
n
n
n
n
- 2 -
1 camera connected:
CPU: Pentium 3, 800MHz
Memory Size: 512MB
2 to 4 cameras connected:
CPU: Pentium 3, 1.3GHz
Memory Size: 512MB
5 to 8 cameras connected:
CPU: Pentium 4, 2.4GHz
Memory Size: 1.0GB
9 to 16 cameras connected:
CPU: Pentium 4, 3.2GHz
Memory Size: 1.0GB

2 Setting Up the Camera
Installing the Camera Stand
The camera comes with a camera stand, which uses a swivel ball
screw head to lock to the camera’s screw hole. When the camera
stand is attached, you can place the camera anywhere by mounting
the camera through the three screw holes located in the base of the
camera stand.
- 3 -

Connecting the Camera to LAN/WLAN
Use the provided Ethernet cable to
connect the camera to your local
area network (LAN).
When you connect the AC power
adapter, the camera is powered on
automatically. You can verify the
power status from the Power LED
on the front panel of the camera.
Once connected, the Link LED
starts flashing green light and the
camera is on standby and ready
for use now.
If you use a wireless network in
your application environment, you
need to attach the included
external antenna to the camera.
When the camera is powered on,
the camera will automatically
search any access point with
“default” SSID.
NOTE If the camera cannot to your wireless network, you need to
install the camera in LAN and proceed with WLAN settings.
- 4 -
Connecting the Ethernet Cable
Connecting the External Antenna

3 Accessing the Camera
Using IPFinder
The camera comes with a conveniently utility, IPFinder, which is
included in the Installation CD-ROM, allowing you to search the
camera on your network easily.
1. Insert the Installation CD-ROM into your computer’s CD-ROM
drive to initiate the Auto-Run program.
2. Click the IPFinder item to launch the utility. The control panel will
appear as below.
3. Once you get the IP address of the camera, launch the Web
browser or Xview Recording & Viewing Software to access your camera.
TIP The Installation CD-ROM provides a setup program that allows you
to install IPFinder on your computer. To install IPFinder, click Install
Software then select IPFinder on the Auto-Run screen.
Display the connected
camera(s)
Double click to link the
camera
Click About to get the Version information of IPFinder.
Click Link to connect the selected camera.
Click Search to find the IP address of the connected camera(s).
Click Change IP to modify the IP address of the selected camera.
Click Exit to close the utility.
- 5 -

1. Open the Web browser on your computer (for example, Microsoft
Internet Explorer in this guide)
2. Type the default IP address (192.168.0.30) or the IP address found
by IPFinder in the Address bar, and then press [Enter].
3. When the login window appears, enter the default User name (admin)
and password (admin) and press OK to access to the main screen of
the camera’s Web Configuration.
- 6 -
Accessing to the Camera

- 7 -
4. Click Setup and then Smart Wizard to set up your camera
quickly. The Smart Wizard will guide you through the
necessary settings with detailed instructions on each step.

- 8 -
4 Tips
For more information, please refer to the Advanced Installation
Guide on the provided Installation CD-ROM.
For details of operating XView, please refer to the Software
User Guide on the provided Installation CD-ROM.

IP CCTV
Manufactured exclusively for:
Xvision (Europe) Group,
Head Office: London, U.K.
Email: [email protected].uk
Web: www.x-vision.co.uk
TECHNICAL SUPPORT:
For Technical Support for any Xvision product please contact your local distributor.
LIMITED WARRANTY:
This product is supplied with a 1 Year warranty. The Warranty excludes products
that have been misused, (including accidental damage) and damage caused by
normal wear and tear. In the unlikely event that you encounter a problem with
this product, it should be returned to the place of purchase.