Xantrex MS2000 User manual

MS2000 Sine Wave Inverter/Charger
Operation Guide
MS2000

MS2000 Sine Wave Inverter/Charger
Operation Guide

About Xantrex
Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from
50 watt mobile units to one MW utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup
power applications in both grid-connected and stand-alone systems. Xantrex products include inverters, battery
chargers, programmable power supplies, and variable speed drives that convert, supply, control, clean, and distribute
electrical power.
Trademarks
MS2000 Sine Wave Inverter/Charger is a trademark of Xantrex International. Xantrex and Xanbus are registered
trademarks of Xantrex International.
Other trademarks, registered trademarks, and product names are the property of their respective owners and are used
herein for identification purposes only.
Notice of Copyright
MS2000 Sine Wave Inverter/Charger Operation Guide © August 2004 Xantrex International. All rights reserved.
Disclaimer
UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC. (“XANTREX”)
(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY
TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.
(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT,
INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH
INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.
Date and Revision
August 2004 Rev A
Part Number
975-0125-02-01
Contact Information
Telephone: [phone] (toll free North America)
1 360 925 5097 (direct)
Fax: [phone] (toll free North America)
1 360 925 5143 (direct)
Email: [e-mail]
Web: www.xantrex.com

975-0125-02-01 iii
About This Guide
Purpose
The MS2000 Sine Wave Inverter/Charger Operation Guide provides explanations
and procedures for operating, configuring, and troubleshooting the MS2000 Sine
Wave Inverter/Charger (MS2000).
Scope
The guide provides safety guidelines and information about operating,
configuring, and troubleshooting the unit. It does not include installation
information or battery information. Refer to the MS2000 Sine Wave Inverter/
Charger Installation Guide.
For detailed information about particular brands of batteries, you will need to
consult individual battery manufacturers.
Audience
The guide is intended for users who need to operate, configure, and troubleshoot
the MS2000 Sine Wave Inverter/Charger.
Organization
This guide is organized into four chapters and three appendixes.
Chapter 1, “Introduction”, outlines the main performance and safety features of
the MS2000 Sine Wave Inverter/Charger. Reading this chapter will give you a
clear understanding of the inverter/charger’s capabilities.
Chapter 2, “Operation”, provides information about operating the MS2000.
Details are provided on how to read the front panel indicators to monitor the
MS2000.
Chapter 3, “Configuration”, explains how to configure the MS2000 from the
control panel.
Chapter 4, “Troubleshooting”, explains how to identify and solve problems that
can occur with the MS2000.
Appendix A, “Specifications”provides electrical, physical, and performance
specifications for the inverter/charger. It also provides Echo Charger
specifications.
Appendix B, “Battery Charging Reference for the Main Charger”provides
information on three-stage charging, two-stage charging, and charging times.
Appendix C, “Terminology”provides a glossary and a listing of commonly used
abbrevations and acronyms.

About This Guide
iv 975-0125-02-01
“Warranty and Product Information”contains the product warranty, explains how
to return a product for service, and describes what to prepare for a call to Xantrex
Customer Service.
Conventions Used
The following conventions are used in this guide.
Symbols Used
The following symbols are used on the product labels or in this guide.
WARNING
Warnings identify conditions or practices that could result in personal injury or
loss of life.
CAUTION
Cautions identify conditions or practices that could result in damage to the unit or
other equipment.
Important: These notes describe an important action item or an item that
you must pay attention to.
&
In this guide: Important information, warnings or cautions.
On the product: Important information, warnings or cautions
with further explanation in the product guides.

AC –Alternating current
(
DC –Direct current
%
Warning: Hot surface. Do not touch.

DC ground connection point

AC safety ground connection point from incoming AC source

AC safety ground connection point for AC output (to AC loads)

About This Guide
975-0125-02-01 v
Related Information
For related materials on this product and its available accessories, see also:
MS2000 Sine Wave Inverter/Charger Installation Guide (975-0126-02-01)
System Control Panel Owner’s Guide (975-0083-01-01)
Automatic Generator Start Owner’s Guide (975-0082-01-01)
Xanbus System Installation Guide (975-0136-01-01)
More information about Xantrex Technology Inc. as well as its products and
services, including a complete list of Xanbus-enabled devices, is available at
www.xantrex.com
Contact Information
Telephone: [phone] (toll free North America)
1 360 925 5097 (direct)
Fax: [phone] (toll free North America)
1 360 925 5143 (direct)
Email: [e-mail]
Web: www.xantrex.com

vi

975-0125-02-01 vii
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS
The MS2000 Sine Wave Inverter/Charger Operation Guide contains important
safety instructions.
Before you install and use your MS2000 Sine Wave Inverter/Charger, be sure to
read, understand and save these safety instructions and those in the other product
guides.
Read all instructions and cautionary markings on the inverter/charger, the
batteries and all appropriate sections of this guide.
1. Use of accessories not recommended or sold by Xantrex Technology, Inc.
may result in a risk of fire, electric shock, or injury to persons.
2. The inverter/charger is designed to be permanently connected to your AC and
DC electrical systems. Xantrex recommends that all wiring be done by a
certified technician or electrician to ensure adherence to the local and national
electrical codes applicable in your application.
3. To avoid a risk of fire and electric shock, make sure that the existing wiring is
in good condition and that the wire is not undersized. Do not operate the
inverter/charger with damaged or substandard wiring.
4. To reduce risk of damage and injury, charge only rechargeable
lead-acid batteries: flooded, gel, or absorbed glass mat (AGM) types. Other
types of batteries may burst causing personal injury and damage.
5. Do not operate the inverter/charger if it has received a sharp blow, been
dropped, or otherwise damaged in any way. If the unit is damaged, see the
“Warranty and Product Information”section in the MS2000 Sine Wave
Inverter/Charger Operation Guide.
6. Do not disassemble the inverter/charger; it does not contain user serviceable
parts. Take it to a qualified service person when service or repair is required.
Incorrect reassembly may result in a risk of electrical shock or fire. Internal
WARNING: Risk of injury or loss of life
The MS2000 Sine Wave Inverter/Charger shall not be used in connection with
life support systems or other medical equipment or devices.
WARNING
The following warnings identify conditions or practices that could result in
personal injury or loss of life.

Safety
viii 975-0125-02-01
capacitors remain charged after all power is disconnected. For instructions on
obtaining service, see the “Warranty and Product Information”section in the
MS2000 Sine Wave Inverter/Charger Operation Guide.
7. Do not expose the inverter/charger to rain, snow, or splashing bilge water.
8. To reduce risk of electric shock, disconnect all sources of AC and DC power
from the inverter/charger attempting any maintenance or cleaning. Turning
off controls will not reduce this risk.
9. The inverter/charger must be provided with equipment grounding conductors
connected to the AC input ground and chassis ground terminals.
To reduce the risk of overheating, keep the ventilation openings clear and do not
install the inverter/charger in a compartment with limited airflow or inadequate
clearances around the unit. Refer to the MS2000 Sine Wave Inverter/Charger
Installation Guide for required clearance.
CAUTION
Cautions identify conditions or practices that could result in damage to the unit or
other equipment.