Xerox 850DP - Phaser Color Solid Ink Printer Configuration guide

Phaser
®
850 Color Printer
Cleaning Instructions
075-0580-00 October 1999
Copyright © Tektronix, Inc. Unpublished rights reserved under the copyright laws of the
United States. Contents of this publication may not be reproduced in any form without
permission of Tektronix, Inc.
Tektronix
®
, Phaser
®
, PhaserShare
®
, ColorStix
®
, the TekColor
®
icon, and Made For Each
Other
®
are registered trademarks of Tektronix, Inc. PhaserLink™, PhaserPort™,
PhaserPrint™, PhaserSym™, PhaserTools™, TekSMART™, and the TekColor™ name are
trademarks of Tektronix, Inc. TekColor Care
SM
and RealSUPPORT
SM
are service marks of
Tektronix, Inc.

Cleaning Instructions 1
Cleaning Phaser® 850 Printers
Cleaning Phaser
®
850 Printers
The printer should be cleaned when prints have oily streaks, stray ink or smeared ink. Cleaning may
also be needed when paper is not picking reliably from the paper tray, or the pick and feed rollers are
visibly dirty. How often you need to clean the printer depends on how heavily the printer is used and
the environment in which it is used. Less frequent cleaning is required when high quality, laser bond
paper is used for printing.
Use the following procedures if the printer’s automated paper path cleaning procedure — located in
the Troubleshooting menu, "Remove Ink Smears," — fails to resolve the problem.
Cleaning supplies
The cleaning kit contains presoaked alcohol wipes that are recommended for cleaning the printer.
If you purchase isopropyl alcohol, always use alcohol that is at least 90% pure; alcohol that has
additives can damage the printer.
Warning
Alcohol is flammable; keep alcohol-soaked wipes away from hot surfaces.
Cleaning for oily streaks
1. Open the front cover.
2. Remove the maintenance drawer (A) from the printer.
3. Use a lint-free wipe to gently wipe any excess debris from the clear plastic wiper blade.
4. Reinsert the maintenance drawer into the printer.
0580-1
0379-08

2 Phaser 850 Color Printer
Cleaning Phaser® 850 Printers
Cleaning for ink smears or jams: paper-feed rollers
Clean the paper-feed rollers if media feeds improperly, or if prints have ink smears.
Caution
Hot surfaces exist behind the middle paper-feed rollers. To avoid personal injury during
cleaning procedures, do not reach in behind these rollers.
1. Open the front cover.
2. Remove the maintenance drawer (A) from the printer.
3. The upper paper-feed rollers are located above the slot for the maintenance drawer (A). To clean
these rollers:
a. Place a prepackaged alcohol-soaked wipe against each upper rubber roller, pressing to create
pressure against the roller.
b. Use the thumbwheel to turn the upper rollers. The upper rubber rollers should rotate four or
five complete revolutions for each roller segment to ensure proper cleaning. Scrub each roller
thoroughly. If the wipe becomes dirty, discard it and use another.
4. To clean the middle rubber feed roller behind the metal plate:
a. Place a prepackaged alcohol-soaked wipe against the underside of each middle roller.
b. Using your hand, rotate the middle roller.
0580-1
9103-10

Cleaning Instructions 3
Cleaning Phaser® 850 Printers
c. Scrub each roller thoroughly. If the wipe becomes dirty, discard it and use another.
5. The lower paper-feed rollers are located below the maintenance drawer (A): one set of rollers is
black rubber; the other set is white plastic. To clean the lower rollers:
a. Place and hold a prepackaged alcohol-soaked wipe on top of the white and black rollers.
b. Move the thumbwheel to turn the rollers. Rotate the rollers four or five complete revolutions
for each roller segment to ensure proper cleaning.
c. Scrub each roller thoroughly until clean. If the wipe becomes dirty, discard it and use
another.
6. To clean the shiny metal surface, use a prepackaged alcohol-soaked wipe.
7. Put the maintenance drawer (A) back into the printer, and close the front cover.
9103-11
9103-12
0643-165

4 Phaser 850 Color Printer
Cleaning Phaser® 850 Printers
Cleaning for ink smears or jams: paper-exit path
Clean the paper-exit path if media feeds improperly, or if prints have ink smears.
Caution
To avoid damaging the print drum and rapid release guide, never use any sharp objects in
this area, or scrape excess ink with a tool or fingernail.
1. Open the exit cover.
2. To clean the rubber exit rollers:
a. Wrap an alcohol-soaked wipe around the index finger of one hand.
b. Press your wipe-covered finger against each roller.
c. Move the thumbwheel to turn the rollers. Rotate the rollers four or five complete revolutions
for each roller segment to ensure proper cleaning.
3. To clean the two sets of ribbed exit guides under the exit cover, gently wipe the raised ribs using
an alcohol-soaked wipe.
Note
You may notice some staining of the exit rollers while performing
the cleaning procedure; this is normal and does not indicate
additional cleaning is necessary. Simply clean rollers to remove
any build-up of ink.
9103-15
9103-17

Cleaning Instructions 5
Cleaning Phaser® 850 Printers
4. Lift the blue paper guide to access the rapid release guide.
5. Lift up the blue tabs and remove the rapid release guide.
6. Gently wipe the clear plastic blade with a pre-soaked alcohol cloth. If the rapid release guide is
damaged, replace it.
Caution
Handle the rapid release guide carefully to avoid bending or
damaging the clear plastic edge.
0643-167
0643-151
0643-154

6 Phaser 850 Color Printer
Cleaning Phaser® 850 Printers
7. Reinstall the rapid release guide, pressing down on the blue tabs to snap the blade into place.
8. Close the exit cover.
Cleaning for media tray jams
If the printer incorrectly feeds paper or transparencies, and the pick and feed rollers are visibly dirty,
perform the following cleaning procedures.
Cleaning the media-pick roller
1. Remove the media tray from the printer.
2. Open the front cover.
Caution
Hot surfaces exist behind the upper paper-feed rollers. To avoid
personal injury during cleaning procedures, do not reach in
behind the paper-feed rollers.
0643-153
9103
-
18

Cleaning Instructions 7
Cleaning Phaser® 850 Printers
3. Remove the maintenance drawer (A) from the printer.
4. The top of the media-pick roller is behind the black rubber paper-path rollers. To clean the top
surface of the media-pick roller:
d. Use a prepackaged alcohol-soaked cloth.
e. Scrub the top surface of the media-pick roller thoroughly. If the wipe becomes dirty,
discard it and use another.
5. Replace the maintenance drawer (A) in the printer.
6. Close the front cover.
7. To access the bottom of the media-pick roller reach into the media tray slot. Use a prepackaged
alcohol-soaked cloth. Scrub the bottom surface of the pick roller thoroughly .
8. Replace the upper media tray in the printer.
9103-09
9103-20
9103-21

8 Phaser 850 Color Printer
Cleaning Phaser® 850 Printers
Cleaning for multipicks: separator pad
If the printer picks multiple sheets of paper from the upper tray, clean the separator pad.
1. Remove the upper media tray from the printer.
2. Using an alcohol-soaked cloth, gently wipe the separator pad.
3. Inspect the separator pad for damage to the metal edge; it should be free of dents and lie flat
against the rubber surface. If any damage is seen, the separator pad should be replaced.
4. Replace the upper media tray in the printer.
Cleaning for lower tray jams: paper-feed rollers
If the printer feeds paper incorrectly or feeds more than one sheet at a time from the High-Capacity
Paper Tray Assembly, and the rollers are visibly dirty, perform the following cleaning procedures.
1. Remove the paper tray from the High-Capacity Paper Tray Assembly. If your printer has two
assemblies, remove the tray from each one. The two paper-feed rollers for each assembly are
visible when each tray is removed.
2. Using an alcohol-soaked cloth, scrub the rollers thoroughly. Rotate the roller several times to
ensure proper cleaning.
3. Replace the paper tray in the High-Capacity Paper Tray Assembly.
9103-63
9103-22