Xiaomi Aqara QBCZ11LM Guide

XIAOMI-MI.COM
Smart wall outlet Aqara Smart Socket ZigBee Version
User manual and warranty card
Overview
Smart wall outlet Aqara Smart Socket ZigBee Version is a smart socket, that
uses the ZigBee wireless protocol, does not change the interior of the house, it
is more safe to use, it synchronizes with devices that have the function of the
Aqara multifunctional gateway (hereinafter simply "gateway"), remote control,
turn on or off at a set time, view energy statistics, etc.
* This product can only be used within the premises, it is recommended that
the installation be installed by professionals. Before installation, turn off the
main switch, after installation, turn on the main switch, and connect a smart
wall outlet to the gateway using the mobile application "Mi Home" (for more
details, see "Installation method" and "Adding a device").
1 – Indicator
2 – Button

XIAOMI-MI.COM
Installation
Smart wall socket Aqara Smart Socket ZigBee Version is easy to install, no
need to modify the original wiring, just install it instead of a traditional wall
outlet, the specific installation steps are as follows:
1. Turn off the main power source switch, unscrew the screws on the back of
the socket, connect the supply wire to terminal L and the neutral wire to
terminal N, connect the ground wire to the terminal in the middle, tighten the
screws, the wiring diagram is shown below.
2. Using a flat screwdriver, open the front panel of the socket.
3. Using screws, fix the socket in the box on the wall.

XIAOMI-MI.COM
4. Replace the front panel, outlet installation is complete.
5. Turn on the main switch, the blue indicator flashes 1 time, it means normal
current supply. Press the button, the red LED will flash slowly, it means, that the
socket is working in normal mode, after connecting to the gateway, according
to the steps in the "Add device" option, add a smart wall outlet.
App installation
Enter "Mi Home" in the search bar of the Play Store / App Store, or scan the
QR code below to download the mobile application.
Hotline support: 400-990-7930
Manufacturer: Shenzhen Lumi Lianchuang
Technology Co., Ltd.
Address: Shenzhen City, Nanshan District,
Taoyuan Subdistrict, Liuxian Avenue, 1 Tangling
Road, Jinqi Zhigu Building, Floor 8.

XIAOMI-MI.COM
Adding the device
Open Mi Home application, select the on the Hardware page, click Add Sub-
Device, continue, according to the prompts in the application, until you hear
the voice message "Successfully Connected" from the gateway.
If you are unable to add a device, place the multifunction gateway closer to the
smart wall outlet and try again.
Click Add Sub Device
Press and hold the button for 5
seconds, release when the
Bluetooth indicator starts to blink.

XIAOMI-MI.COM
Main parameters
Model:
QBCZ11LM
Dimensions:
86 × 86 × 45mm
Wireless interface:
ZigBee
Input voltage:
100 - 250V ~, 50Hz
Maximum load:
10A / 2500W
Working temperature:
- 10 - + 50 ° C
Operating Humidity:
Relative humidity 5% -95%, without condensation.
Device Support:
Based on Android 4.4 / iOS 8.0 and higher.
Indicator explanation
Indicator
Device status
Slow flashing red
Failed to establish network connection or
connection failure
Fast flashing blue
The process of connecting the outlet to
the network
Constant blue light
The socket is connected to the mains, the
network is in normal condition
Fast flashing red
Fault, overheating, overload
Constant red light
Phase and zero are reversed
Synchronization Feature Recommendations
You can synchronize a smart wall outlet with even more "smart" devices of
the "smart house" ecosystem
1. Remote switch monitors the outlet, carrying out remote control;
+
Remote switch (attachment to
double-sided scotch tape)
Smart wall outlet Aqara Smart
Socket ZigBee Version

XIAOMI-MI.COM
Synchronization Feature Recommendations
2. When a person returns home, the appliance automatically turns on; when
a person leaves home, the appliance automatically turns off.
+ +
Aqara Door
Sensors
Aqara Human Body
Sensor
Smart wall outlet
Aqara Smart Socket
ZigBee Version
Name and content of harmful substances in the product
Component
name
Harmful substances
(Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE)
Plastic
housing
O O O O O O
Hard plastic
O
O
O
O
O
O
Metal
O
O
O
O
O
O
Resistor
X
O
O
O
O
O
This table is created in accordance with the provisions of the standard
SJ / T 11364.
O: the content of the harmful substance in all the homogeneous
materials of this component is within the requirements of the
standard GB / T 26572.
X: the content of this harmful substance in at least one of the homogeneous
materials of this component exceeds the limits of the requirements of the
standard GB / T 26572.