XtendLan XL-ICA-306M1 User manual

Version 3.0.0
User's manual
XL-ICA-306M1

i
Table of Contents
1Network Connection ...................................................................................................................1
2Main Interface Introduction........................................................................................................2
2.1 Log in ..............................................................................................................................2
2.2 Live Interface .................................................................................................................4
2.3 Encode Setup ................................................................................................................4
2.4 System Menu.................................................................................................................5
2.5 Video Window Function Option ..................................................................................5
2.6 Video Window Setup ....................................................................................................6
3PTZ Control..................................................................................................................................8
4Setup...........................................................................................................................................11
4.1 Camera .........................................................................................................................11
4.1.1 Conditions .............................................................................................................11
4.1.2 Video......................................................................................................................14
4.1.3 Audio......................................................................................................................18
4.2 Network.........................................................................................................................19
4.2.1 TCP/IP...................................................................................................................19
4.2.2 Connection............................................................................................................21
4.2.3 PPPoE ...................................................................................................................23
4.2.4 DDNS.....................................................................................................................23
4.2.5 IP filter....................................................................................................................24
4.2.6 SMTP （e-mail）.................................................................................................25
4.2.7 UPnP......................................................................................................................26
4.2.8 SNMP.....................................................................................................................27
4.2.9 Bonjour ..................................................................................................................29
4.2.10 Multicast .........................................................................................................29

ii
4.2.11 WIFI.................................................................................................................30
4.2.12 Qos..................................................................................................................32
4.3 Event .............................................................................................................................33
4.3.1 Video detect..........................................................................................................33
4.3.2 Alarm......................................................................................................................38
4.3.3 Abnormity..............................................................................................................40
4.4 Storage .........................................................................................................................42
4.4.1 Record schedule and snapshot schedule........................................................42
4.4.2 Destination............................................................................................................43
4.4.3 Record control......................................................................................................45
4.5 System..........................................................................................................................46
4.5.1 General..................................................................................................................46
4.5.2 Account..................................................................................................................49
4.5.3 PTZ.........................................................................................................................53
4.5.4 Default....................................................................................................................53
4.5.5 Import/Export........................................................................................................54
4.5.6 Auto maintenance................................................................................................54
4.5.7 Firmware update..................................................................................................55
4.6 Information ...................................................................................................................55
4.6.1 Version...................................................................................................................55
4.6.2 Log..........................................................................................................................56
5Alarm...........................................................................................................................................58
6Log out........................................................................................................................................59
Important
The following functions are for reference only. Some series products may not
support all the functions listed below.

1
1Network Connection
This series IPC product support the Web access and management via PC.
Web includes several modules includes monitor channel preview, PTZ control, system configuration,
alarm and etc.
Please follow the steps listed below for network connection.
zMake sure the IPC has connected to the network properly.
zIPC IP address and PC IP address shall be in the same network segment. If there is router, please
set the corresponding gateway and subnet mask.
zUse order ping ***.***.***.***(* IP camera address) to check connection is OK or not.

2
2Main Interface Introduction
2.1 Log in
Open IE and input IP camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 2-1.
Figure 2-1 IE
The login interface is shown as below. See Figure 2-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here

3
Figure 2-2 Login Interface
If it is your first time to login in, system pops up warning information to ask you whether install control
webrec.cab or not. Please click OK button, system can automatically install the control. When system is
upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the
control download. Or you can lower the IE security level. See Figure 2-3.
Figure 2-3 Security Settings

4
2.2 Live Interface
After you logged in, you can see the live monitor window. See Figure 2-4.
Figure 2-4 Live Interface
There are four sections:
zSection 1: Encode setup bar
zSection 2: System menu
zSection 3: Window function option bar
zSection 4: Window adjust bar
2.3 Encode Setup
The encode setup interface is shown as in Figure 2-5.
①
④
②
③

5
Figure 2-5 Encode setup
Please refer to the following sheet for detailed information.
Parameter Function
Main stream In normal network width environment, main stream can record
audio/video file and realize network monitor.
You can set the main stream resolution if your device supports.
Sub (Extra)
stream If network width is not sufficient, you can use sub stream to
realize network monitor.
Protocol You can select stream media protocol from the dropdown list.
There are three options: TCP/UDP/Multicast
2.4 System Menu
System menu is shown as in Figure 2-6.
Please refer to chapter 2.2 Live, chapter 3 PTZ, chapter 4 Setup, chapter 5 Alarm, chapter 6 Log out
for detailed information.
Figure 2-6 System Menu
2.5 Video Window Function Option
The interface is shown as below. See
Figure 2-7.
Figure 2-7 Video Window Function
Please refer to the following sheet for detailed information.
SN Parameter Function
1 Alarm
output Click it to generate an alarm output.
2 Digital
zoom Click this button and then left drag the mouse in the zone to
zoom in. Right click mouse system restores original status.
1 2 3 4 5 6

6
3 Snapshot
You can snapshoot important video. All images are
memorized in system folder: \ picture download (default).
You can go to Setup->Camera->Video->Path to modify the
local record save path.
4 Record When you click local record button, the system begins
recording. The recorded file is saved to system folder: \
RecordDownload(default).
You can go to Setup->Camera->Video->Path to modify the
local record save path.
5 Audio
output Turn on or off audio when you are monitoring.(It has no
relationship with system audio setup )
6 Bidirectional
talk Click it to begin audio talk. You can go to Setup->Camera- >Audio to set bidirectional talk mode.
2.6 Video Window Setup
The interface is shown as in Figure 2-8.
Figure 2-8 Video Window Setup
Please refer to the following sheet for detailed information.
SN Parameter Function
1 Image
control Click it to open picture setup interface. See Figure 2-9. This
interface is on the top right pane.
2 Original
size Click this button to go to original size. It is to display the actual
size of the video stream. It depends on the resolution of the
bit stream.
3 Full screen Click it to go to full-screen mode. Double click the mouse or
click the Esc button to exit the full screen.
4 Width and
height ratio Click it to restore original ratio or suitable window.
The picture setup interface is shown as in Figure 2-9.
1 2 3 4

7
Figure 2-9
Please refer to the following sheet for detailed information.
Parameter Function
It is to adjust monitor video
brightness.
It is to adjust monitor video contrast
ness.
It is to adjust monitor video
saturation.
It is to adjust monitor video hue.
Video
setup
Reset Restore brightness, contrastness
saturation and hue to system default
setup.
Note:
zAll the operations here
apply to WEB end
only.
zPlease go to Setup-
>Camera->Conditions
to adjust
corresponding items.