XtendLan SDOMEO4802701 User manual

SDOMEO4802701
Outdoor Day/Night Speed Dome
with built in Sony CCD 27x
optical zoom camera
SDOME4802201
Indoor Day/Night Speed Dome
with built in Sony CCD 22x
optical zoom camera
User’s Guide

Safety Attention Notes
● Please read the instructions thoroughly before installing or operating the unit.
● Please do not put the machine on an unstable table or mounting bracket.
● Please prevent all liquids or other contaminating material from entering into the dome
housing.
● When connecting to the power source, please follow all electric safety standards and
only use the power supply designated for this device. The speed dome's RS-485 and
video signal uses TVS technology to protect it from strong electric surges. This
technology prevents damage to the device resulting from impulse signals such as
lightning strikes or surges under 500W power. Allow for enough distance between the
RS-485 and video signals and high-voltage equipment or cables during the
transmission process. Please do not power the unit until all connections are secure
and installation is complete.
● Avoid shooting very bright objects directly into the camera's CCD (such as the sun or
light fittings).
● When the machine is not operating properly, do not casually repair it. Refer to the
instructions for information about how to service or repair your speed dome.
● Please protect the unit against extremes of vibration, pressure or dampness while
transporting unit. Damage can occur from improperly packaging the unit while
shipping.
● Please only install the outdoor dome camera system in outdoor environments.

Contents:
1 Introduction ...............................................................................................................................5
2 Technical Data ............................................................................................................................5
2.1 Technical Parameter of Intelligent High-speed Dome .................................................................. 5
2.2 2.2.
Camera Parameter for High-speed Dome: .................................................................................... 6
3 Setting, Installation, Connection .................................................................................................6
3.1 Dome Address, Transmission Speed, Protocol Setting.................................................................. 6
3.1.1 Speed Dome Camera Address Setting ................................................................................... 7
3.1.2 Speed Dome Camera Communication Protocol Setting ....................................................... 8
3.1.3 Speed Dome Camera Transmission Speed Setting (Baud Rate Setting)................................ 8
3.1.4 RS-485 Bus Matching Resistance .......................................................................................... 8
3.2 Installation, Connection ................................................................................................................ 9
3.2.1 Installation Requirement....................................................................................................... 9
3.2.2 Outdoor Speed Dome Camera Wall Hanging Installation ..................................................... 9
3.2.3 Indoor Hemisphere Dome Camera Recessed Installation...................................................13
4
Control Keyboard Control Use Instruction to Speed Dome Camera .......................................................15
4.1 Setting and Adjusting Preset Position .........................................................................................15
4.1.1 Setting Preset Position ........................................................................................................ 16
4.1.2 View Preset Position............................................................................................................16
4.2 Dome Pattern Tours ....................................................................................................................16
4.2.1 Preset Position Parameter Setting ......................................................................................17
4.2.2 Sequence Setting................................................................................................................. 18
4.3 Auto Scanning (2points scanning, 360° scanning)....................................................................... 18
4.3.1 2 Points Scan .......................................................................................................................18
4.3.2 360° Scan.............................................................................................................................19
4.4 Objective Tracking .......................................................................................................................19
4.5 Camera Control ........................................................................................................................... 20

4.5.1 Zoom Control....................................................................................................................... 20
4.5.2 Focus Control.......................................................................................................................20
4.5.3 Iris Control ...........................................................................................................................20
4.5.4 Auto Backlight Compensation .............................................................................................20
4.5.5 Auto White Balance............................................................................................................. 20
5 Camera Menu Setting ...............................................................................................................21
6 Protocol Order Chart.................................................................................................................23
6.1 PELCO-D
, PELCO-P Protocol Order Chart..................................................................................... 23
7 Exception Handling ...................................................................................................................24

1Introduction
Congratulations on purchasing our speed dome, an intelligent, high-speed dome
camera with a high-performance DSP camera and sophisticated zoom lens. It is an
advanced technological surveillance product combining an all-direction variable speed
dome and digital decoder all in one unit. It can aim quickly and scan continuously,
making omni-directional and non-blind-spot monitoring into reality. Additionally, it can
quickly adapt to changing environments with its 18x optical and 12x digital zoom
with precise stepping motors. The advanced stepping motor technologies enable
the dome to rotate smoothly, respond sensitively and aim precisely. The speed dome
camera has memorizing function when the power cuts off, can auto resume to
previous working status before the power cuts off. Use the high-performance speed dome
“ When
it Counts.
”
All of the features make the intelligent high-speed dome camera fit for a wide
range of applications such as intelligent building, bank, street of city, airport, station etc.
2Technical Data
2.1 Technical Parameter of Intelligent High-speed Dome
Model Outdoor Day/Night
Speed Dome Indoor Speed Dome
Power Supply AC24VDC12V, 3A
Operating temperature -40°C~+60°C0°C~+40°C
Operating moisture
≤ 95%
Power consumption 20W
Communication RS485 bus
Communication transmission speed 1200/2400/4800/9600bps
Horizontal rotation speed
0.4°- 280° (1-64 grade shift gears)
Horizontal rotation range 360° unlimited rotation
Tilt rotation range 90 °
Auto f lip Rotates 180° when camera tilts to the vertical position
Auto zoom speed control Control speed auto-adjusted according to zoom length
changing
2 points scan Can set freely
2 points scan speed 1－64 grade available
Dwell time(2 points scan) 1－60s available
Preset Positions 128 pcs
Running to preset speed:
1－64 grade available, 0.4° - 280°
Dwell time at preset position 1－60s available
Cruise Tour: 8 group
Cruise Points Qty per cruise group 16 preset positions
Fan, Heater Fan and heater auto-starts 12VAC NIL

2.2 2.2. Camera Parameter for High-speed Dome:
Model Outdoor Day/Night
Speed Dome Indoor Speed Dome
Mode
¼" Sony Exview (Day/Night) CCD
¼" Sony Exview (Day/Night)
CCD
Scan 2:1 Interlace 2:1 Interlace
Resolution >480 lines >480 lines
Minimum illumination 0.8lux/0.01lux (b/w mode) 1lux/0.01lux (b/w mode)
Iris Auto/manual Auto/manual
Focus Auto/manual Auto/manual
Zoom 27x optical 22x optical
Focal length f=4 – 88mm f=3.25 – 88mm
Angle of view 44° (wide), 2° (Tele-) 52° (wide), 2° (Tele-)
Backlight compensation Backlight compensation Backlight compensation
White balance Auto Auto
Gain Auto Auto
Signal PAL/NTSC PAL/NTSC
S/N ratio>55dB >55dB
Video signal output 1.0 ± 0.2Vp-p 1.0 ± 0.2Vp-p
3Setting, Installation, Connection
3.1 Dome Address, Transmission Speed, Protocol Setting
Before the dome is installed, the communication protocol, baud rate and dome address, should be
confirmed. Set the code switch, keeping the setting consistent with the control system. The
relative code switch site and connecting wire are diagrammed below for reference.
Note: Internal version has only 6 SW2 switches.

3.1.1 Speed Dome Camera Address Setting
The address code for the speed dome should be properly set before use to ensure accurate
operating order of the controller at the control centre and to control many dome cameras. The
address code is made up of ADD (8 bits) on PCB board. The 8 bits switch uses the 8421
binary coded decimal system. The largest value is established at 256. 1 means ON status
and 0 means OFF status. Each dome address code and keyboard relative screen display
mode is represented in the chart below (see the following figure and the address/digits in
following chart)
SW 2 switch (Address settings for PELCO P):
With reference to the above chart: When all code switches are under
“ OFF ” status on speed
dome, address code is 1. When you input Numerical key No.1 on control keyboard, then
press CAM key for confirmation showing that set keyboard address as No.1 control address.,
At this time, keyboard can control speed dome camera(its control address is 0001). Other
address is to be set as above.
SW 2 switch (Address settings for PELCO D):

3.1.2 Speed Dome Camera Communication Protocol Setting
SW 1 switch:
3.1.3 Speed Dome Camera Transmission Speed Setting (Baud Rate Setting)
The 5th and 6thbits of FUN on the PCB board are used to set the baud rate (see following
figure). The default baud rate setting is 9600.
SW1 switch:
3.1.4 RS-485 Bus Matching Resistance
For central controlling, the matching resistance should be set for the device that is furthest
away from the controller. There is an end matching resistance switch on FUN. The 8th bit of
FUN shows ON status (see chart below) which means the BUS matching resistance has
been connected.

3.2 Installation, Connection
Attention!
1. Installation should only be handled by a qualified CCTV expert.
2. For detailed connection information, please refer to silk-screen print instruction on PCB and
installation guide or manuals.
3. Because the dome is a high-grade optical unit, please never touch any of the optical
components.
4. For a clear image, the dome cover should be cleaned periodically. When cleaning, position
your hand to hold dome's outer loop to prevent finger sweat acidity from corrupting the
surface of the dome. If the dome is scratched, it will affect image quality. Therefore please use
a soft dry cloth or similar products to clean its outer surface. If the dust is heavy, you can use a
neutral cleanser.Any advanced furniture cleanser can be used to clean the dome exterior.
Installation Preparation
3.2.1 Installation Requirement
● Installation should be handled by a qualified service agent and should comply with all local
regulations, Service personnel should forecast potential problem such as falling objects, outer
breach, building vibration or other similar conditions.
● Check for all necessary materials, and ensure if the selected installation location is suitable for
the speed dome.
3.2.2 Outdoor Speed Dome Camera Wall Hanging Installation
· Wall Hanging Installation
ATTN: Installation locations should endure 5 times weight of total weight (dome camera,
mounting bracket and mounting base) to avoid in shaken images.

a. Set wall bracket mounting on the wall. Draw out center site of the hole on the wall against bracket
sample
b. Use drill to make 4 holes with the M8 size at the designated site. Screw in M8 bolt for mounting
c. Put power, communication and video lines through bracket hole, leaving enough wire
length Maneuverability.
d. Fix the bracket to the wall with 4 M8 bolts and mounting tray.
· Housing Installation
a. Remove housing from the packing and put the cable into the bracket from bracket top. Install
G1 1/2 bolt on the top of housing into the bolt of wall bracket. At the same time, use two M8
bolt to secure in place.