XtendLan SDOMEOIR6-CM10 User manual

SDOMEOIR6-CM10
SDOMEOIR6W-SD2121
User manual

WARNINGS AND CAUTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS
THROUGH VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user the presence of non-insulated “dangerous voltage” within the product’s
enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to
different persons.
The exclamation point within an equilateral triangle, is intended to alert the user the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying this product.

PRECAUTIONS:
1. Persons without technical qualifications should not attempt to operate this dome device before
reading this manual thoroughly.
2. Remove any power to the dome before attempting any operations or adjustments inside the
dome cover to avoid potential damage to the mechanism.
3. Inside the dome cover there are precision optical and electrical devices. Heavy pressure,
shock and other sudden adjustments or operations should be avoided. Otherwise, you may
cause irreparable damage to the product.
4. Please DO NOT remove or disassemble any internal parts of the video camera to avoid
normal operation and possibly void the warranty. There are no serviceable parts inside the
camera.
5. All electrical connections to the dome should be made in strict accordance with the attached
labels and wiring instructions in this manual. Failure to do so may damage the dome beyond
repair and void the warranty.
6. For outdoor installation especially in high places or poles, it is highly recommended that the
proper lightning arrestors and surge suppressors are installed before the dome is entered into
service.
7. Please do not use the product under circumstances where the limits exceed the maximum
specified temperature, humidity or power supply specifications.

IMPORTANT SAFEGUARDS
1. Read these instructions before attempting installation or operation of dome device.
2. Keep these instructions for future reference.
3. Heed all warnings and adhere to electrical specifications. Follow all instructions.
4. Clean only with non abrasive dry cotton cloth, lint free and approved acrylic cleaners.
5. Should the lens of the camera become dirty, use special lens cleaning cloth and solution to
properly clean it.
6. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.
7. Use only attachments or accessories specified by the manufacturer.
8. Verify that the surface you are planning to use for attaching the dome can adequately support
the weight of the device and mounting hardware.
9. Protect this device against lighting storms with proper power supplies.
10. Refer all servicing to qualified service personnel. Servicing is required when the device has
been damaged in any way, when liquid traces are present, or the presence of loose objects is
evident or if the device does not function properly, or has received sever impact or has been
dropped accidentally.
11. Indoor dome is for indoor use only and not suitable for outdoor or high humidity locations.
Do not use this product under circumstances exceeding specified temperature and humidity
ratings.
12. Avoid pointing the camera directly to the sun or other extremely bright objects for prolonged
period of time avoiding the risk of permanent damages to the imaging sensor.
13. The attached instructions are for use by qualified personnel only. To reduce the risks of
electric shock, do not perform any servicing other than contained in the operating instructions
unless you are qualified to do so.
14. During usage, user should abide by all electrical safety standards and adhere to electrical
specifications for the operation of the dome. The control cable for RS485 communications as
well as the video signal cables should be isolated from high voltage equipment and high voltage
cables.
15. Use supplied power supply transformer only.

INDEX
1 Product Introduction ............................................................................................................... 1
1.1 Specification ........................................................................................................................ 2
1.2 Performance Features ........................................................................................................ 3
1.3 Function Description ........................................................................................................... 4
2 Installation ................................................................................................................................ 6
2.1 Product Dimension .............................................................................................................. 6
2.2 Bracket Dimension .............................................................................................................. 6
2.3 Installation ........................................................................................................................... 7
2.4 Connection ......................................................................................................................... 7
3. Instruction ............................................................................................................................... 8
3.1 Power OnAction. ................................................................................................................ 8
3.2 Basic Function .................................................................................................................... 8
3.3 Special Function ................................................................................................................. 9
3.4 Screen Character Operation ............................................................................................. 10
4 OSD Menu .............................................................................................................................. 11
4.1 System ............................................................................................................................. 12
4.2 Dome Function ................................................................................................................. 12
4.2.1 Preset ........................................................................................................................ 12
4.2.2 Scan .......................................................................................................................... 13
4.2.3 Guard Tour ................................................................................................................. 13
4.2.4 Pattern ....................................................................................................................... 14
4.2.5 Privacy Zone .............................................................................................................. 14
4.2.6 Other ..........................................................................................................................15
4.2.7 Alarm ......................................................................................................................... 15
4.3 Camera ............................................................................................................................. 16
4.3.1 CAMADV .................................................................................................................. 16
4.3.2 CAMAE ..................................................................................................................... 16
4.4 IR. ......................................................................................................................................17
4.5 Display .............................................................................................................................. 17
4.6 Time .................................................................................................................................. 17
4.7 Language .......................................................................................................................... 18
4.8 Reset ................................................................................................................................ 18
Appendix ⅠAnti-lightning, Anti-surges .................................................................................. 19
Appendix ⅡClean Transparent Cover ..................................................................................... 19
Appendix ⅢCommon Knowledge on RS-485 Bus ................................................................. 20
1. Basic Feature of RS-485bus ............................................................................................... 20
2. Mode of Connection and Terminal Resistance ......................................................................20
Appendix ⅣException Handling ............................................................................................. 21

6
1 Product Introduction
1.1 Specification
Horizontal Rotation Speed
0.02°-200°/s
Tilt Rotation Speed
0.02°-120°/s
Horizontal Rotation Range
360°
Tilt Rotation Range
93°
Auto Flip
Horizontal 180°, Vertical 93°
Ratio Speed
Support
Auto control IR LED
PWM
IR Testing Time
2-15s selectable
Ambient Light Testing
0-50 grades
IR Illumination On
0-25 grades selectable
IR Output Power
1-9 grades selectable
IR Standby Power
1-9 grades selectable
IR Standby Time
2-15s selectable
A-B Scan
User programmable
A-B Scan Speed
1-9 speed setting available
360° Scan Speed
1-9 speed setting available
Dwell Preset
5-60s interval
Preset Points
220
Go to Preset Speed
200°/s
Guard Tours
4 groups
Guard Points
Max.16 points, dwell time user selectable
Pattern Scan
4 pcs
Pattern Scan Record
max.15 minutes, max.512 commands
Park Time
1-60mins available
PWR on Action
Memory/Pattern/Tour/360° scan/A-B scan/Preset 1-8/None
Park Action
Pattern/Tour/360° scan/A-B scan/Preset 1-8/None
Communication Protocol
Pelco-D, Pelco-P
Communication
RS485 Bus
Baud Rate
1200/2400/4800/9600bps
Soft ID
1-255
Privacy Mask
Support (according to zoom module type)
3D Location
Support (DH-SD1)
OSD Menu
Multiple Language
Time Scheduling function
8 tasks
Alarm
4 inputs and 2 outputs (Optional)
Timing Run
Built-in high precision RTC clock, support time management
Operating Temperature
Indoor: 0°~ +40° Outdoor: -40°~ +60°
Operating humidity
≤95% Non Condensing
Heater & Blower
Auto temperature control
Power
AC/DC15-28V ≤3A
Lightning protection
Transient voltage 6000V
IR Illumination Distance
50M
Power Consumption
≤ 15W
Compatible Camera
SONY, HITACHI, SAMSUNG, LG, CNB etc.
LED Type
Ø16=6

7
1.2 Performance Features
PWM function. Intelligent IR illumination & power consumption is variable, dependant
the zoom factor.
3D allocation. That screen coordinate location and zoom local are performed at the
same time can be available.
Privacy masking. 24 privacy masking areas can be random set (module support).
Supported Protocols. Pelco-D/P; Others on special request.
4 path patterns. Each path can record 512 different instructions or 900s path
operation.
Manual control speed. The lowest 0.02º/s smooth running can be available.
4 guard groups. The dwell position and time of 16 preset points of each group can
be edited independently.
Optional IP module (built in provision).
Built-in high density RTC clock supports time management function.
Optional alarm, 4 alarm inputs and 2 alarm outputs.
Park action. If users don’t operate the dome in set time, it will automatically run
preset guard group, trace memory group, pan scan etc.
Memory of operation before power off.
Built-in fan and heater can control the temperature automatically.
Heater works below 0℃and fan works above 40℃.
Multiple languages for OSD menu: English, German, Italian, French, Spanish.
Illumination to ambient light can be adjustable.
Accurate step motor control makes it stable running, precise location and sensitive
reaction.
Completed metal body construction, waterproof IP 66.
Built-in 6000V anti-lighting and anti-surge protection equipment.

8
1.3 Function Description
Alarm Linkage
Intelligent dome camera supports 4 switch alarm inputs, 1 switch output and 1 digital output.
When the dome camera has detected the alarm closed signal, it will run the preset action which
can be one of the calling preset points or no action.
Auto-adaptive to Protocol and Module
The dome can auto-adaptive to the multi protocol and most of the module without changing the
DIP switch.
3D Allocation
With this function users can move the image of some area to the center of screen according to
specified level and vertical coordinates and auto control to zoom according to zoom parameter
set. Screen coordinate location and zoom local can be available via the software support.
Privacy Masking
In the monitoring scope, areas that users can’t or aren’t willing to make show in the screen of
the monitor can be set as privacy protected area (area masking), such as area where
customers enter the password in monitoring system of bank or some doorway.
Trace Memory (Pattern Scan)
The traces of camera’s any running action in every directions of PTZ can be saved, which is
called pattern scan. In pattern scan the camera turning to up, down, left and right and zooming
in or out can be saved. This function remembers and imitates a process of operator’s operation.
This dome camera has 4 path patterns. Each path can record 512 different instructions or the
longest 15mins’ path operation. Opening any one of the paths can remember automatically the
present running trace and scan cyclically according to the recorded trace.
Zero Alignment
There is a point specified as zero point. When the dome is working, the preset point is not
accurate caused by the operator. User can make the dome automatically enable the zero
alignment by operational order.
Auto Flip
In the manual scanning mode, when beyond the maximum angle in tilt and if the joystick is held
continuing in tilt direction, the dome will automatically rotate 180 degree in horizontal direction
to maintain continuity of scanning. So vertical 180° continuous monitoring comes true.
Focus
The auto focus enables the camera to focus automatically to maintain clear image. User can
use manual focus to get expected image in special condition.
Under the following conditions camera will not auto focus on the camera target:
(1) Target is not in the center of the screen;
(2) Attempting to view images that are far and near at the same time;
(3) Target is strongly lighted object, such as neon lamp, etc.;

9
(4) Targets are behind the glass covered with water droplets or dust;
(5) Targets are moving quickly;
(6) Monotonous large area targets, such as wall;
(7) Targets are too dark or faint.
BLC(Back Light Compensation)
If the light of background is bright, the target in the picture may appear dark or as a shadow.
BLC enhances exposure of the target in the center of the picture. The dome adjusts the iris
according to the center of the pictures. If there is a bright light source outside this area, it will
wash out to white. The camera will adjust the iris so that the target in the sensitive area will be
properly exposed.
Iris Control
Factory default is automatic camera aperture, in mode of which camera senses changes in
ambient light through moving and adjust automatically lens aperture to make the brightness of
output image stable.
Ratio Speed
Intelligent pan and tilt speed is variable depend on the zoom factor. When zooming in, the
speed will become slower and when zooming out, the speed will become faster.
360 Scan
Dome 360°clockwise continuously scans the display scene at set speed in horizontal direction
under the condition that pitch angle remains the same. In the scanning status, operator can
move the joystick to exit from scanning.
Preset
After the dome camera keeps arbitrary PTZ location, it will automatically move to the defined
position when preset is called.
Guard Tour Scan
Dome patrol scans according to certain edited preset order.
Limited Points Scan (A-B Scan)
The dome operates reciprocating scanning the real scenarios at a certain speed between the
set left and right points. The range of left and right points boundary is 20° - 340°.
Power Off Memory
This feature allows the dome to resume its previous preset or status after power is restored. By
default setting, the dome support power up memory, which improves the reliability and avoids
repeated settings of the parameter.
Park Action
If users don’t operate the dome in set time, it will automatically run preset specific mode (pan
scan,A-B scan, park action, cruise, preserve action etc.).
Multilanguage OSD Menu
The available language on screen menu can be English, German, Italian, French or Spanish.

1
0
User can set the function or parameter, or check the related information through the OSD.
Return to PTZ Function
Return dome’s pan and tilt and camera zoom value to the control device.
2 Installation
2.1 Product Dimension
2.2 Bracket Dimension

1
1
2.3 Installation
2.4 Connection
Connection of RS485
Before connecting, please turn off the power and read carefully the instructions of all connected
devices. Please use the standard power we supply and don’t lengthen the power cable
arbitrarily.
Fig 24

8
IR SPEED DOME
PROTOCOL PELCO-D/P
COMM 2400.N.8.1
DOME ID 001
MODULE
VERSION V1.2
PAN INIT
TILT INIT
POWER ON
IR SPEED DOME
PROTOCOL PELCO-D/P
COMM 2400.N.8.1
DOME ID 001
MODULE
VERSION V1.2
PAN OVER
TILT OVER
POWER ON
IR SPEED DOME
PROTOCOL PELCO-D/P
COMM 2400.N.8.1
DOME ID 001
MODULE XXX
VERSION V1.2
PAN OVER
TILT OVER
POWER ON
3. Instruction
3.1 Power On Action
When initializing the system, the operation as left figure will run
in 2 seconds.
When restoring out-of-factory settings, please wait patiently.
The operation as left figure will run in 1 minute.
This left figure means initializing the pan/tilt motor of speed
dome camera.
The initialization of pan/tilt motor completes. It is initializing the
camera and detecting the module of camera.
.
XXX is the specific model of camera module which is displayed
after camera finishes detection.
Power on self testing completes.
3.2 Basic Function
Dome Running
Control joystick or up, down, left and right key in the keyboard.
Zoom

9
Press ZOOM- button to make the lens farther and minify the scene.
Press ZOOM+ button to make the lens closer and magnify the scene.
Focus
After FOCUS- button is pressed, the object in vicinity will become clearer while the object far
away will become ambiguous.
After FOCUS+ button is pressed, the object far away will become clearer while the object in
vicinity will be ambiguous.
Iris
Press IRIS- to gradually shrink the iris and decrease the image brightness.
Press IRIS+ to enlarge the iris and increase the image brightness.
Preset Point
Setting preset, press button “preset” + ”number” + ”enter”.
Calling preset, press button “call” + ”number” + ”enter”.
Deleting preset, press button “clear” + ”number” + ”enter”.
Remark: Some preset points are used tentatively for special functions.
3.3 Special Function
The follow presets are predefined as special function, please shot+ preset No.+ enter to enable
those functions:
PREST
FUNCTION
PRESET
FUNCTION
33
Pan scan180 º
86
BLC on
34
Reset
87
BLC off
75
Trace memory 1
88
Freeze on
76
Trace memory 2
89
Freeze off
77
Trace memory 3
91
Limited Points Scan (A-B scan)
78
Trace memory 4
92
Set left point of A-B scan
79
Digital zoom on
93
Set right point of A-B scan
80
Digital zoom off
94
OSD menu off
81
Auto day/night
95
OSD menu on
82
Switch to night
96
Guard tour 3
83
Switch to day
97
Guard tour 2
84
Force on far light
98
Guard tour 1
85
Force on near light
99
Pan scan
Note: If use some other equipments to control IR dome, some special functions probably can’t
be effective because of the limit of protocol.

10
3.4 Screen Character Operation
Call preset 95 to enter the OSD, call preset 94 to exit the OSD.
Up or Down: Move the option of the OSD, change the value on the OSD.
Right: Enter the option, select the item or confirm.
Left: Return to main menu or cancel.
Zoom Display: x XXX, XXX is the present zoom of camera.
Time Display: XXXX(year)-XX(month)-XX(day) XX(hour)-XX(minute)-XX(second)
Angle Display: XXX.XX(pan)/XXX.XX(tilt)
IR Display: ☀means the IR display status is on. means the IR is on.
Remark: “-”means the cursor selecting some option. “”means editing the content of some
options.

11
4 OSD Menu

12
DEVICE ID
CHECK ID
TARGET ID
001
BAUD RATE
2400
SAVE
EXIT
PRESET NO
001
CALLPRESET
<SETPRESET>
EXIT
4.1 System
<MAIN MENU>
<SYSTEM>
<DOME>
<CAMERA>
<IR>
<DISPLAY>
<TIME>
<LANGUAGE>
<RESET>
EXIT
<SYSTEM>
PROTOCOL PELCO-D/P
COMM 2400.N.8.1
DOME ID 001
MODULE
VERSION
< COMM SET>
EXIT
<COMM SET>
<SYSTEM>
PROTOCOL: Display the protocol of the dome.
COMM: 2400. N. 8. 1 means the communication
information. 2400 is baud rate. COMM form: Baud rate.
Check bit. Data bit. Start bit.
DOME ID: Display the dome address. The range is
000-255.
MODULE: Display the brand and model of camera.
VERSION: Version will be updated along with the
product upgrading.
<COMM SET>
DEVICE ID: It is only and used to distinct from the
ID of other domes.
CHECK ID: Distinguishing several domes with same
ID and altering target ID, soft protocol and baud rate
need to enter check ID in line with the device ID,
otherwise altering can’t be completed.
TARGET ID: Target ID can be changed and edited
on line. It will be effective immediately after changed.
“Dial the address number” on this mini dome is not
available.
BAUD RATE: Baud rate is selectable. 1200, 2400,
4800, 9600 are available. Default is 2400.
4.2 Dome Function
4.2.1 Preset
<PRESET>
PRESET NO: Select the preset number needing
to be operated, whose range is 001-
220.
CALL PRESET: Call the preset number edited.
<SETPRESET>
Entering SET PRESET displays the content as left
figure. Call preset 1 to save and call preset 2 to

13
SCAN
SCAN SPEED 5
EXIT
<GUARD TOUR>
GUARD TOUR NO 1
CALL GUARD TOUR
<GUARD TOUR >
EXIT
PRESET NO
001
CALLPRESET
<SETPRESET>
PRESET 1: SAVE
PRESET 2: BACK
<PRESET> back.
Because some presets are used to realize special
functions, they can not be set and called normally.
4.2.2 Scan
SCAN SPEED: Scan speed includes setting the
speed of limited points scan (A-B scan) and
360°scan. Its range is 1-9 grades.
Note: The effective range of left and right boundary is 20-340°.
4.2.3 Guard Tour
This dome camera can set 4 groups of guard tour. Each group has 16 points and each point
can be set alone the dwell time and tour speed.
GUARD TOUR NO: It has 1-4 groups settable.
CALL GUARD TOUR: Call the guard tour ID edited
successfully.
<GUARD TOUR> <GUARD TOUR>
ID
01
POINT
01
TIME
05
SPEED ID: The tour sequence of guard tour group. Its range
64 is 1-16.
02
02
05
64 POINT: The preset of guard tour. Its range is 01-64
03 03 05 64 settable.
04
04
05
64
05
05
05
64

TIME: The default time of all points is 05s. Its range
06
06
05
64
is 05-60s.
07
07
05
64

SPEED: The speed between two points in each
08
08
05
64
guard tour group can be set alone. Its range is 1-64
<NEXT PAGE> grades.
<GUARD TOUR>
ID POINT TIME SPEED
09 09 05 64
10 10 05 64
11 11 05 64
12 12 05 64
13 13 05 64
14 14 05 64
15 15 05 64
16 16 05 64
SAVE
Note: Preset 33 and 34 can’t be set as guard tour point.

14
4.2.4 Pattern
<PATTERN>
PATTERN NO 1
CALL PATTERN
<PATTERN>
EXIT
<PATTERN>
PATTERN NO 1
CALL PATTERN
<PATTERN>
XXX/512
PRESET 1: SAVE
PRESET 2: BACK
PATTERN NO: Factory default is 1.
Select the pattern needing to be edited. 1-4 pattern are
effective.
CALL PATTERN: Call the patterns having been
edited.
<PATTERN>
Left figure shows the status when entering to the pattern set.
“XXX” means the quantity of operator’s running pattern, and
512 is the most amount of the instruction.
Remark: The precision of pattern is associated with the system
settings and the module of camera. When using the pattern,
the user is recommended to turn off the privacy zone and
unnecessary display function.
4.2.5 Privacy Zone
<DOME>
<PRESET>
<SCAN>
<GUARD TOUR>
<PATTERN>
<PRIVACYZONE>
<OTHER>
<ALARM >
EXIT
<PRIVACYZONE>
MASK NO
MASK ON
<SETMASK>
EXIT
<PRIVACYZONE>
MASK NO 01
MASK ON
<SETMASK>
PRESET 1: SAVE
PRESET 2: BACK
MASK NO: Select the mask number. It
depends on the module supported.
SET MASK: For detailed steps, please refer to the
“Example of Setting Mask 1”.
MASK: ON and OFF are selectable.
Example of Setting Mask 1
1: Move the cursor to MASK NO, which is be selected by
pressing the right key of direction.
2: Press the “up and down” keys in the keyboard to edit the
mask number as 1, which is be entered by pressing the
right key. “-”means selecting this mode, while “”means
editing this mode.
3: Move the cursor to <SET MASK> and press right key to set
the position of privacy zone. See the figure on the left below.
4: Shake the joystick to aim at the object. Use the ZOOM+ and
ZOOM- keys in the keyboard to adjust the size of picture. And
use iris OPEN and CLOSE keys to adjust the size of mask. Call
preset 1 to save and exit and call preset 2 to exit directly.
Remark: The mask size is better more than double the target
size. Setting mask is associated with the pitch angle which is
advised equal to or less than 45°by the factory.

15
4.2.6 Other
<DOME>
<PRESET>
<SCAN>
<GUARD TOUR>
<PATTERN>
<PRIVACYZONE>
<OTHER>
<ALARM >
EXIT
<OTHER>
PARK MODE NONE
PARKTIME 05
POWER ON ACT MEMORY
RATIO SPEED ON
AUTO FLIP ON
EXIT
PARK MODE: There are 13 actions of NONE,
Pattern 1, Tour 1, 360 scan, AB scan, Preset 1-8
selectable.
PARK TIME: The dome camera runs home
position after a period of idle time which is home time
and whose range is 1-60 mins.
POWER ON ACT: There are 14 actions of Memory,
Pattern 1, Tour 1, 360 scan, AB scan, Preset 1-8,
NONE selectable.
RATIO SPEED: Ratio speed can be set as ON or
OFF status.
AUTO FLIP: The dome camera operated flips
horizontally 180° when beyond the maximum angle. If
continuing withholding the joystick when beyond the
maximum angle in tilt, it flips horizontally 180°and 0°in
tilt. So vertical 180°whole continuous monitoring
comes true.
4.2.7 Alarm
<DOME>
<PRESET>
<SCAN>
<GUARD TOUR>
<PATTERN>
<PRIVACYZONE>
<OTHER>
<ALARM >
EXIT
<ALARM>
ALARM IN OFF
ALARM OUT NC
PATROLTIME 05S
ALARM 1 PRESET-01
ALARM 2 PRESET-02
ALARM 3 PRESET-03
ALARM 4 PRESET-04
EXIT
ALARM IN: Alarm input has OFF and ON selectable.
ALARM OUT: Alarm output has NC an NO
selectable.
DWELLTIME: Its range is 05-10S.
ALARM 1: No action and preset 1-16 are selectable.
ALARM 2: No action and preset 1-16 are selectable.
ALARM 3: No action and preset 1-16 are selectable.
ALARM 4: No action and preset 1-16 are selectable.
Note: If there are several alarm inputs at the same time, the
system will respond to the alarm inputs in turn according to the
dwell time.

16
4.3 Camera
<CAMERA>
ZOOM LIMIT
FOCUS MODE AUTO
DIGITAL ZOOM OFF
ZOOM SPEED HIGH
<ADV>
<AE>
EXIT
ZOOM LIMIT: Display the maximum zoom position,
which relates to that digital zoom is OFF or ON.
FOCUS MODE: Auto and manual are selectable.
DIGITAL ZOOM: Digital zoom has
ON/OFF selectable.
ZOOM SPEED: Zoom speed has HIGH and LOW
selectable.
4.3.1 CAM ADV
<CAM ADV>
WB MODE AUTO
RED GAIN AUTO
BLUE GAIN AUTO
SHARPNESS 05
BLC OFF
WDR OFF
EXIT
WB MODE: There are indoor, outdoor, auto, manual
selectable.
RED GAIN: It can only be adjusted under the
condition that the WB mode is manual. And its range is
000-255.
BLUE GAIN: It can only be adjusted under the
condition that the WB mode is manual. And its range is
000-255.
SHARPNESS: Its adjustable range is 0-15 grade.
BLC: It has ON and OFF selectable.
WDR: It has ON and OFF selectable.
4.3.2 CAM AE
<CAMAE>
AE MODE AUTO
IRIS MODE AUTO
IRIS TIME AUTO
SHUTTER AUTO
GAIN AUTO
ICR DAY
EXIT
IRIS TIME: Set the speed of iris varying.
SHUTTER: Set the camera shutter. There are auto
and manual shutter selectable.
GAIN: GAIN has auto and manual selectable.
ICR: It has auto, day and night selectable.
Remark:
1. Iris, shutter and gain can only be set under the condition that AE mode is manual.
2. D/N switch function can only switch automatically normally under the condition that
AE mode is auto.
3. All the above functions are available if the camera supports.