XtendLan XL-ICA-206M2T-M39 User manual

XL-ICA-206M2T-M39
DOME IP camera
User manual

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. Please note: Do not connect these two
power supplying sources to the device at the same time; it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding holes of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

3
Accessory Name
Amount
Network Camera
1
Quick Start Guide
1
CD
1
Installation Accessories Bag
1
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

4
Table of Contents
1General Introduction...................................................................................................................1
1.1 Overview ........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications ................................................................................................................2
1.3.1 Performance...........................................................................................................2
1.3.2 Factory Default Setup...........................................................................................3
2Structure ...................................................................................................................................11
2.1 Dimensions ................................................................................................................ 11
2.2 Port Description ......................................................................................................... 11
2.3 Bidirectional talk ........................................................................................................ 15
2.3.1 Device Connection ............................................................................................ 15
2.3.2 Operation ............................................................................................................ 15
2.4 Alarm Setup ............................................................................................................... 15
3Installation ................................................................................................................................ 17
3.1 Device Installation Introduction ............................................................................... 17
3.2 Device Installation Steps ..........................................................................................17
3.2.1 General Installation ........................................................................................... 17
3.2.2 Manual Zoom Lens Focus Operation ............................................................. 21
3.2.3 Side Cable Exit ................................................................................................... 21
3.2.4 Cable Connection .............................................................................................. 22
3.3 SD Installation ........................................................................................................... 23
4Quick Configuration Tool ....................................................................................................... 24
4.1 Overview .................................................................................................................... 24
4.2 Operation ................................................................................................................... 24
5Web Operation .........................................................................................................................27

5
5.1 Network Connection ................................................................................................. 27
5.2 Login and Main Interface ......................................................................................... 27
6FAQ .......................................................................................................................................... 30
Appendix Toxic or Hazardous Materials or Elements .............................................................. 31

1
1General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
audio and video data collection, transmission together. It can connect to the network directly without any
auxiliary device.
This series network camera uses standard H.264 video compression technology and G.711a audio
compression technology, which maximally guarantee the audio and video quality.
This series network camera enclosure has the strong resistance capacity, which can guarantee the
proper work performance under heavy strike. It supports real-time monitor and listening at the same time.
It supports analog video output and dual-way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the network
and then use a network client-end. Due to its multiple functions and various uses, this series network
camera is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
• Different user rights for each group, one user belongs to one group.
• The user right shall not exceed the group right.
Storage
Function
• Support central server backup function in accordance with your configuration and
setup in alarm or schedule setting
• Support record via Web and the recorded file are storage in the client-end PC.
• Support built-in SD card.
• Support local SD card hot swap, support short-time storage when encounter
disconnection.
Alarm
Function
• Real-time respond to external local alarm input and video detect as user pre-
defined activation setup and exert corresponding message in screen and audio
prompt(allow user to pre-record audio file)
• Real-time video detect: motion detect, camera masking.
• Can generate an alarm when network abnormal, SD card abnormal event
occurred.
Network
Monitor
• Network camera supports one-channel audio/video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
• Max supports 20 connections.
• Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
• Support web access, widely used in WAN.
Network
Management
• Realize network camera configuration and management via Ethernet.
• Support device management via web or client-end.
• Support various network protocols.
Peripheral
Equipment
• Support the on-off alarm device to alarm via the sound or the light.
Power
• External power adapter DC12V/AC 24V
• Support PoE.
Assistant
Function
• Log function
• Support PAL/NTSC

2
• Support system resource information and running status real-time display.
• Day/Night mode auto switch (electromagnetic ICR switch).
• Built-in IR light. Support IR night vision (For HDBW Series only).
• Backlight compensation: screen auto split to realize backlight compensation to
adjust the bright.
• Support electronic shutter and gain setup.
• Support video watermark function to avoid vicious video modification.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
System
Main
Processor
TI Davinci high performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the same
time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
SD card status, bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
Pixel
1920（H）*1080（V）
Day/Night
Mode
Support day/night mode switch and electromagnetic IR-CUT at the same
time.
Auto Iris
DC drive
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
Manual/Auto
Electronic
Shutter
Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Motorized
Focus
Support remote motorized focus function.
Video
Compression
Standard
H264/JPEG/MJPEG
Video Frame
Rate
PAL:
Main stream（1920*1080@25fps）extra stream（704*576@25fps）
NTSC:
Main stream（1920*1080@30fps）extra stream（704×480@30fps）
Video Bit Rate
H.264: 56Kbps-8192Kbps. It is adjustable
ＭJPEG: 128Kbps-0480Kbps. It is adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.

3
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, privacy mask.
Lens
3~9mm@F1.2motorized zoom focus lens
Lens Interface
¢14. Lens is the default accessories.
Audio
Audio Input
1-channe
Audio Output
1-channel
Bidirectional
Talk Input
Reuse the first audio input channel
Audio Bit Rate
16kbps 16bit
Audio
Compression
Standard
G.711a/G.711u/PCM
Video
Motion Detect
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Video Loss
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Alarm Input
1-channel input，1-channel output
Recor d and Backu p
Record
Priority
Manual>External alarm >Video detect>Schedule
Local Storage
Support Micro SD card storage
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
HTTP,TCP,ARP,RTSP,RTP,UDP,RTCP,SMTP,FTP,DHCP,DNS,DDNS,PP
POE,IPv4/v6,SNMP,QoS,UPnP,NTP.
Remote
Operation
Monitor, system setup, log information, maintenance , upgrade and etc
AUX
Interface
Video Output
1-channel analog video output，BNC port, 9-pin port connection
Reset
Built-in RESET button
IR light
IR distance 10 to 20 meters (For HDBW series product only)
General Parameter
Power
Support AC24V/DC12V power. PoE
Power
Consumption
General series: below 5W. IR series: below 7W.
Working
Temperature
-10℃~+60℃
Working
Humidify
10%~90%
Dimensions(m
m)
¢151x119
Weight
1.25Kg
Installation
Support various installation modes
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.

4
Function
Setup Type
Item
Default setup
Camera Setup
Conditions
Brightness
50
Contrast
50
Hue
50
Saturation
50
Gain mode
Auto
Gain limit
80
Exposure mode
Auto
Auto iris
Enable
Scene mode
Auto
Day/night mode
Auto
BLC
Off
Flip
Disable
Video
Video bit
stream
Main
stream
Bit stream
type
General
Encode
mode
H.264B
Resolution
1080P
（1920*1080）
Frame rate
（FPS）
PAL: 25
NTSC:30
Bit stream
type
CBR
Reference bit
rate
3584-8192 Kb/S
Bit rate
8192
I frame
interval
50
Watermark
settings
Enable
Watermark
character
DigitalCCTV
Extra
stream
Enable
Enable
Bit stream
type
General
Encode
mode
H.264B
Resolution
CIF(352×288/35 2×240)
Frame rate
（FPS）
PAL: 25
NTSC:30
Bit rate type
CBR
Reference bit
rate
192-1024Kb/S

5
Function
Setup Type
Item
Default setup
Bit rate
640
I frame
interval
50
Snapshot
Snap type
General snap
Image size
1080P
（1920*1080）
Quality
Better
Interval
7s
Overlay
Privacy mask
Enable
Channel title
Enable
Time title
Enable
Path
Snapshot
path
C:\PictureDownload
Record path
C:\RecordDownload
Audio
Main stream
Enable
Enable
Encode
mode
G.711A
Sub(Extra) stream
Enable
Disable
Encode
mode
G.711A
Network setup
TCP/IP
Host name
IPC
Ethernet card
Wire(Default)
Mode
Static
MAC
address
Depends on the device
IP version
IPV4
IP address
192.168.1.168
Subnet mask
255.255.255.0
Default
gateway
192.168.1.1
Preferred
DNS
8.8.8.8
Alternate
DNS
8.8.8.8
Enable
ARP/Pingto
to set IP
address
service
Enable
Connection
Max
connection
10
TCP port
37777
UDP port
37778

6
Function
Setup Type
Item
Default setup
HTTP port
80
RTSP port
554
PPPoE
Enable
Disable
User name
N/A
Password
N/A
DDNS
Server type
Disable ，CN99 DDNS
Server IP
none
Port
80
Domain
name
none
User name
none
Password
N/A
Update
period
5m
IP filter
Trusted sites
Disable
SMTP（email）
SMTP server
none
Port
25
Anonymity
Disable
User name
anonymity
Password
N/A
Sender
none
Authenticatio
n (Encrypt
mode)
N/A
Title
(Subject)
IPC Message
Main
Receiver
N/A
Interval
0s
Health email
Disable ，interval=60m
UPnP
Enable UPnP
Disable
SNMP
SNMP v1
Disable
SNMP v2
Disable
SNMP port
161
Read
community
public
Write
community
private
Trap address
N/A
Trap port
162
Bonjour
Enable
Enable

7
Function
Setup Type
Item
Default setup
Server name
“Device name+SN”.
Depends on the device.
Multicast
Multicast
address
239.255.42.42
Port
36666
Auto register
Enable
Disable
SN
1
Server IP
0.0.0.0
Port
7000
Sub-device
ID
none
WIFI
On(Enable)
Enable
QoS
Real-time
monitor
0
Command
0
Event
management
Video detect
Motion detect
Enable
Disable
Anti-dither
5 seconds
Sensitivity
3
Record
Channel
Enable
Record
Delay
10 seconds
Relay
(Alarm)
output
Enable
Alarm delay
10s
Send email
Disable
Activation
N/A
Address
0
Snapshot
Disable
Video (Camera) masking
Enable
Disable
Record
Channel
Enable
Record
Delay
10 seconds
Relay out
Enable
Record
Delay
10 seconds
Send email
Disable
Activation
Disable
Address
0

8
Function
Setup Type
Item
Default setup
Snapshot
Disable
Alarm setup
Relay (Alarm) activation
Enable
Disable
Relay input
Alarm1
Anti-dither
5s
Sensor type
NO
Record
channel
Enable
Record delay
10s
Relay
(Alarm)
output
Enable
Relay
(Alarm) delay
10s
Send email
Disable
Activation
N/A
Address
0
Snapshot
Disable
Relay (Alarm)
output
1
Abnormity
No SD card
Enable
Disable
Relay
(Alarm)
output
Enable
Relay output
delay
10s
Send email
Disable
Capacity warning
Enable
Disable
Capacity limit
(Space
threshold)
10%
Relay
(Alarm)
output
Enable
Relay output
delay
10s
Send email
Disable
SD card error
Enable
Disable
Relay
(Alarm)
output
Enable
Relay output
delay
10s
Send email
Disable

9
Function
Setup Type
Item
Default setup
Disconnection
Enable
Disable
Record
Enable
Record delay
10s
Relay
(Alarm)
output
Enable
Relay output
delay
10s
IP conflict
Enable
Disable
Record
Enable
Record delay
10s
Relay
(Alarm)
output
Enable
Relay output
delay
10s
Storage
management
Destination(Storag
e )
FT
P
FTP enable
Disable
Server IP
N/A
Port
21
User name
anonymity
Password
N/A
Remote
storage path
share
Emergency
storage to
local path
Disable
Network storage
NAS enable
Disable
Mode
NFS
Server IP
N/A
Port
21
User name
N/A
Password
N/A
Remote
storage path
N/A
Conditions (Record
control)
Pack
duration
8m
Pre-record
5s
Disk full
Overwrite
Record mode
Auto
System
management
General setup
al set u
Device name
Device factory SN
Language
English

10
Function
Setup Type
Item
Default setup
Video
standard
NTSC
Date and time
Date format
Y-M-D
Time format
24H
Time zone
GMT+08:00
Current time
Sync PC
DST
Disable
DTS type
Week
Start time
00:00:00 of the first Sunday of the
month
End time
00:00:00 of the second Monday of
the month
Synchronize
with NTP
Disable
NTP server
clock.isc.org
Port
37
Update
period
10m
Auto maintenance
Auto reboot
Enable
Auto delete
old files
Disable

11
2Structure
2.1 Dimensions
You can refer to the following figures for dimension information. The Unit is mm. See Figure 2-1 and
Figure 2-2.
Figure 2-1
Figure 2-2
2.2 Port Description
For the non-IR series product, the interface is shown as in Figure 2-3 and Figure 2-4.

12
Figure 2-3
Figure 2-4
For the IR motorized zoom lens series product, the interface is shown as in Figure 2-5 and Figure 2-6.

13
Figure 2-5
Figure 2-6
For the IR manual zoom lens series product, the interface is shown as in Figure 2-7 and Figure 2-8.

14
Figure 2-7
Figure 2-8
Please refer to the following sheet for detailed information.
SN
Definition
1
AC 24V power port. The middle pin is for GND.
2
DC 12V power port. The left is the negative end and the right
is the positive end.
3
External cable exit.
4
RJ45 network port.

15
5
I/O signal port：1—ALM_NO；2—ALM_COM；3—GND；
4—ALM_IN；5—GND；6—AUDIO_IN；7—AUDIO_OUT；
8—GND；9—VIDEO_OUT.
6
Reset
7
Five menu operation buttons.
Push T button up—long focus and push W button down—
wide angle.
Push the F button left—Near and push the N right—Far.
Click the middle button is to enable auto focus.
Please note it is for motorized zoom lens only.
8
Status indicator light
9
Fan port
10
Micro-SD card slot
11
12V DC port
12
Network port
2.3 Bidirectional talk
2.3.1 Device Connection
Before the operation, connect the active pickup to the audio input port of the device. Connect the active
speaker to the audio output port of the device. Please make sure the client-end device has the audio
input and output function. For example, you need to connect the microphone and then earphone to the
PC if you want to implement the bidirectional talk function.
2.3.2 Operation
Login the Web and click the bidirectional talk button to enable this function. Click this button again; you
can close current bidirectional talk.
2.4 Alarm Setup
The alarm interface is shown as in Figure 2-9. Please follow the steps listed below for local alarm input
and output connection.
1) Connect the alarm input device to the alarm input port (No.3 pin or No.4 pin) of the I/O cable.
2) Connect the alarm output device to the alarm output port (No.2 pin) and alarm output public port (No.1
pin). The alarm output port supports NO (normal open) alarm device only.
3) Open the Web, go to the Figure 2-9. Please set the alarm input 01 port for the first channel of the I/O
cable (No.3 pin). The alarm input 02 is for the 2nd channel of I/O cable (No.4 pin). Then you can select
the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is the
No.2 pin of the I/O cable.