XtendLan XL-ICA-106M3 User manual

XL-ICA-106M3
Megapixel Indoor
Quick Start Guide

Accessory Name
Amount
XL-ICA-106M3
■
1
Welcome
Thank you for purchasing our IP camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
Before you replace the SD card, please unplug the power cable and then remove the shell.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
2．Installation
Do not apply power to the IP camera before completing installation.
Do not put object on the IP camera.
3．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
The working temperature ranges from -10’C to +60’C. Please keep it away from the electromagnetic
radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the XL-ICA-106M3.
4. Daily Maintenance
Current series XL-ICA-106M3 has no power button. Please unplug all corresponding power cables
before your installation.
Do not touch the CCD or CMOS part; you can use the blower to clean the dust on the surface of the
lens. You can use the dry cloth with some alcohol to clear if necessary.
Please keep the dustproof cap back to protect the CCD or CMOS part if the IP camera does not work
for a long time.
If there is too much dust on the housing, please use the water to dilute the mild detergent first and then
use it to clean the device with the clear dry cloth. Finally use the dry cloth to clean the device.
5. Accessories
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.

C/CS adapter
■
1
Quick Start
Guide
■
1
CD
■
1

Table of Contents
1 Framework...................................................................................................................................5
1.1 Rear Panel.....................................................................................................................5
1.2 Side Panel .....................................................................................................................9
1.3 Lens................................................................................................................................9
2 Installation .................................................................................................................................11
2.1 Lens Installation..........................................................................................................11
2.1.1 Auto Aperture Lens.............................................................................................11
2.1.2 Manual Lens.........................................................................................................11
2.1.3 Remove Lens.......................................................................................................12
2.2 SD Card .......................................................................................................................12
2.2.1 Installation ............................................................................................................12
2.2.2 Remove.................................................................................................................13
2.3 3G Card .......................................................................................................................14
2.3.1 Installation ............................................................................................................14
2.3.2 Remove.................................................................................................................14
2.4 3G/WIFI Antenna........................................................................................................15
2.4.1 Installation ............................................................................................................15
2.4.2 Remove.................................................................................................................16
2.5 I/O Port.........................................................................................................................17
3 Quick Configuration Tool.........................................................................................................18
3.1 Overview......................................................................................................................18
3.2 Operation .....................................................................................................................18
4 Web Operation..........................................................................................................................21
4.1 Network Connection...................................................................................................21
4.2 Login and Logout........................................................................................................21
Appendix Toxic or Hazardous Materials or Elements ...............................................................24

5
1 Framework
1.1 Rear Panel
This series IP camera real panel is shown as below. See Figure 1-1.
The rear panel with the network port
The rear panel with the 100M fiber port
Figure 1-1
Please refer to the following sheet for detail information.
Interface Name
Connector
Function
VIDEO OUT
Video output port
BNC
Output analog video
signal. Can connect to

6
TV monitor to view
video.
AC 24V/ DC 12V
Power port
- Power port.
- Input 12V DC or
AC 24V
STATUS
Indication Light
Red light
- System boot up-
red light is on
- Safe mode-red
light flashes
- System
upgrades-red light
flashes
- System resets-
red light flashes.
Green light
- Normal working
status-green light
is on.
- Display record
status: Record-
green light
flashes.
Yellow light
- Wireless status
light:
- Wireless data
transmission-
yellow light
flashes.
- Detect the
wireless device-
yellow light is on.
3G port
Connect to 3G/WIFI
antenna
Please note it is the
reserved function.
Current series XL-
ICA-106M3
does not support this

7
function right now.
WIFI
3G/WIFI port
Connect to 3G/WIFI
antenna to receive the
wireless signal.
Please note this
function is for some
series products only.
IN
Alarm input port
I/O port
Alarm input port 1. To
receive the signal from
the external alarm
device.
NO
1-ch alarm output
Alarm output port. To
output alarm signal to
the alarm device.
- NO: Normal open
alarm output end.
- C: Alarm output
public end.
C
G
GND
Alarm input ground
end.
A
RS485 port
RS485_A port, control
external PTZ
B
RS485_B port, control
external PTZ
RX
RS232 port
RS232_RX，RS232
receive end.
TX
RS232_TX，RS232
COM send out end.
G
GND
RS232 ground end
NA
Reserved port
N/A
RESET
RESET button
Restore factory default
setup.
When system is
running normally

8
(power indication light
is red), press the
RESET button for at
least 5 seconds,
system can restore
factory default setup.
AUDIO OUT
Audio output port
Audio output 3.5mm
JACK port.
Output audio signal to
the device such as
sound box.
AUDIO IN
Audio input port
Audio input 3.5mm
JACK port.
Input audio signal.
Receive signals from
devices such as pick-
up.
LAN
Network port
Ethernet port
- Connect to
standard Ethernet
cable.
- Support PoE
function.
OPT
100M fiber port
155M single fiber
dual-direction SFP
fiber module
Transmit 100M
Ethernet data.
SD
SD card port
Connect to SD card.
Note
- When you install
the SD card,
please make sure
current card is not
in write mode and
then you can
install it to the
camera.
- When you
remove the SD
card, please
make sure current

9
card is not in write
mode. Otherwise
it may result in
data loss or card
damage.
- Before hot swap,
please stop
record operation.
GND
Please make sure the
device is securely
earthed to prevent the
thunderstorm strike.
1.2 Side Panel
Please refer to the following interface for side panel dimension information. The unit is mm. See
Figure 1-2.
Figure 1-2
1.3 Lens
Please refer to the following interface for lens dimension information. The unit is mm. See Figure
1-3.

10
Figure 1-3

11
2 Installation
2.1 Lens Installation
2.1.1 Auto Aperture Lens
Please follow the steps listed below for auto aperture lens installation. The interface is shown as
in Figure 2-1 and Figure 2-2.
- Remove the CCD protection cap of the device, and then line up the lens to the proper
installation position. Turn clockwise until the lens is fixed firmly.
- Insert the lens cable socket to the auto lens connector in the side panel.
Figure 2-1
2.1.2 Manual Lens
Install C type lens
- Remove the CCD protection cap; use the cross-head screwdriver to remove the screw near
the focal circle. Then please turn counter clockwise to move the focal circle out for several
millimeters. Now you can focus manually.
- Then please use the cross-head screwdriver to fix the screw back firmly. Secure the focal
circle.
- Install the C/CS adapter to the camera.
- Finally, line up lens to the proper installation. Turn clockwise to fix the lens firmly.
Install CS type lens
- Remove the CCD protection cap; use the cross-head screwdriver to remove the screw near
the focal circle. Then please turn counter clockwise to move the focal circle to the end and
now you can focus manually.
- Then please use the cross-head screwdriver to fix the screw back firmly. Secure the focal
circle.
- Finally, line up lens to the proper installation. Turn clockwise to fix the lens firmly.

12
Figure 2-2
2.1.3 Remove Lens
Please follow the steps listed below to remove lens. The interface is shown as in Figure 2-3.
- Turn the lens counter clockwise and then remove it from the camera.
- Unplug the auto lens cable socket from the auto lens connector. If you are using the manual
aperture lens, please skip to the following step.
- If there is no lens, please put the CCD protection cap back to protect the CCD.
Figure 2-3
2.2 SD Card
2.2.1 Installation
Please follow the steps listed below to install SD card. The interface is shown as in Figure 2-4
and Figure 2-5.
- Use the screwdriver to loosen the SD card protection screw in the rear panel, and then
remove the SD card protection cap from the camera.
- Install the SD card to the camera according to the proper installation position.
- Put the SD card protection cap back.
- Use the screwdriver to fix the SD card protection cap screw firmly to secure the SD card
protection cap in the camera.

13
Figure 2-4
2.2.2 Remove
Figure 2-5
Please follow the steps listed below to remove SD card. The interface is shown as Figure 2-6.
- Use the screwdriver to loosen the screw of SD card protection cap in the rear panel.
Remove the cap from the camera.
- Follow the SD card direction to remove the SD card.
- Insert the SD card protection cap.
- Use the screwdriver to fix the screw to secure the protection cap.
Figure 2-6

14
2.3 3G Card
2.3.1 Installation
The 3G card installation is the same with the SD card.
Please follow the steps listed below to install 3G card. The interfaces are shown as Figure 2-7
and Figure 2-8.
- Use the screwdriver to loosen the 3G card protection cap screw in the side panel, and then
remove the 3G card protection cap from the camera.
- Install the 3G card to the camera according to the proper installation position.
- Put the 3G card protection cap back.
- Use the screwdriver to fix the 3G card protection cap screw firmly to secure the 3G card
protection cap.
Figure 2-7
2.3.2 Remove
Figure 2-8
Please follow the steps listed below to remove 3G card. The interface is shown as Figure 2-9.
- Use the screwdriver to loosen the screw of 3G card protection cap in the rear panel.
Remove the cap from the camera.
- Follow the 3G card direction to remove the 3G card.
- Insert the 3G card protection cap.
- Use the screwdriver to fix the screw to secure the protection cap.

15
Figure 2-9
2.4 3G/WIFI Antenna
2.4.1 Installation
Line up the thread of the screw of the 3G/WIFI antenna to the thread of the rear panel. See
Figure 2-10.
Please turn according to the direction in the following figure until antenna is secure firmly. See
Figure 2-11.
Figure 2-10
Figure 2-11

16
After you fix the 3G/WIFI antenna to the WIFI port of the rear panel, you can adjust the antenna
direction. See Figure 2-12.
2.4.2 Remove
Figure 2-12
Use your hands to hold the 3G/WIFI thread end and then turn according to the following figure.
See Figure 2-13.
Now you can see the antenna is away from the thread. See Figure 2-14.
Figure 2-13
Figure 2-14

17
Remove the 3G/WIFI antenna from the port of the rear panel. See Figure 2-15.
Figure 2-15
2.5 I/O Port
Install Cable
Please follow the steps listed below to install the cable. See Figure 2-16.
Use the small slotted screwdriver to press the corresponding button of cable groove. Insert the
cable into the groove and then release the screwdriver.
Remove Cable
Please follow the steps listed below to remove the cable.
Use the small slotted screwdriver to press the corresponding button of cable groove. Remove the
cable out of the groove and then release the screwdriver.
Figure 2-16

18
3 Quick Configuration Tool
3.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you
can use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
3.2 Operation
Double click the “ConfigTools.exe” icon; you can see an interface is shown as in Figure 3-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 3-1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure
3-2.
Figure 3-2

19
Select the “Open Device Web” item; you can go to the corresponding web login interface. See
Figure 3-3.
Figure 3-3
If you want to modify the device IP address without logging in the device web interface, you can
go to the configuration tool main interface to set.
In the configuration tool search interface (Figure 3-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the
Login button to go to the login interface. See Figure 3-4.
In Figure 3-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in
Web Network interface. Otherwise, you can not login the device.
If you are use device background upgrade port 3800 to login, other setups are all invalid.
Figure 3-4
After you logged in, the configuration tool main interface is shown as below. See Figure 3-5.

20
Figure 3-5
For detailed information and operation instruction of the quick configuration tool, please
refer to the Quick Configuration Tool User’s Manual included in the resources CD.