Yakima Prorack K089 User manual

K089
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4
Revision No: 3C 1

Fitting Kit K089
MAX kgs (lbs)
W/P WHD
Saab
900 , 5dr Hatch 94-98 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
900 , 5dr Hatch Feb 94-98 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
900 , 5dr Hatch Feb 94-Jan 98 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
9000 , 4dr Sedan 92-98 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
9000 , 4dr Sedan 92-98 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
9000 , 4dr Sedan Feb 92-Dec 98 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vauxhall
Cavalier , 4dr Sedan 89-95 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Cavalier , 4dr Sedan 89-95 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 5dr Hatch 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Opel
Vectra , 4dr Sedan 89-95 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 89-95 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 89-95 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 89-95 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 89-95 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 89-95 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 5dr Hatch 95-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Holden
Vectra , 4dr Sedan 96-Feb 03 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 96-Feb 03 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 96-Feb 03 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 96-Mar 03 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 96-Mar 03 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 4dr Sedan 96-Mar 03 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 5dr Hatch 96-Feb 03 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Vectra , 5dr Hatch 96-Mar 03 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Citroen
Xantia , 5dr Hatch 93-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Xantia , 5dr Hatch 93-01 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
2

Fitting Kit K089
Xantia , 5dr Hatch Nov 93-01 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Xantia , 5dr Hatch Nov 93-01 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Xantia , 5dr Hatch Sep 93-Jan 01 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Xantia , 5dr Hatch Sep 93-Jan 01 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
3

Fitting Kit EN
K089
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K089
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K089
●Remove locking screw.
●Fit clamp into clamp block at an angle as
shown.
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
6

Fitting Kit EN
K089
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Pull back rubber seal to expose fixed points
on vehicle body.
●Reveal the fixed points. They may be
concealed behind a painted sticker.
7

Fitting Kit EN
K089
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Ensure that the crossbar is adjusted evenly
at both ends.
●Ensure the clamp pin is inserted into the
fixed point and the clamp sits flat to the
body side.
●Repeat for all four positions.
●Refit rubber seal over the clamp.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8

Fitting Kit EN
K089
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9

Fitting Kit EN
K089
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10