YAMAN HRF-40 User manual

To be retained
User’s Manual
Home Beauty Device Bright Lift HRF-40
Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Safety Precautions
. . . . . . . . . . . . . . . . . . . . . .
1
When Using Outside of Japan
. . . . . . . . . . .
9
Names and Functions of Components. . . . 11
Before Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
How to Use
. . . . . . . . . . . . . . . . . . . . . . . . . . .
19
After Treatment
. . . . . . . . . . . . . . . . . . . . . .
27
Additional Information . . . . . . . . . . . . . . . . 29

Troubleshooting
. . . . . . . . . . . . . . . . . . . .
29

Frequently Asked Questions
. . . . . . . . . .
31

Product Specifications
. . . . . . . . . . . . . .
32
After-sales Service
. . . . . . . . . . . . . . . . . . . .
33
Table of
Contents

1
* ‘Property damage’ refers to damage affecting a dwelling, household belongings, or domestic animals and pets.
DANGER Improper use of this device poses a severe and likely risk of death or
serious injury.
WARNING
Improper use of this device may pose a risk of death or serious injury.
ATTENTION
Improper use of this device may result in injury or property damage*.
This symbol shows you what you must do.
This symbol shows you what you must be careful with.
Thank you for purchasing a YA-MAN product.
• Please read this User’s Manual carefully for information on how to use the device properly and safely.
• After reading the contents hereof, be sure to keep this User’s Manual in an accessible location.
• Make sure to include this User’s Manual if you are transferring ownership of the device to another person.
 Classifications of Precautions  Symbols
• Read these Safety Precautions carefully before using the device in order to use it correctly.
• Use the device sensibly in accordance with the prescribed steps.
• Immediately discontinue use and arrange to have the device repaired if any abnormality occurs.
• Do not use the device in a defective state, as doing so could cause physical harm to the user.
• The precautions listed in the User’s Manual are very important. For your safety, please follow them carefully.
• Precautions are classified as DANGER, WARNING, or ATTENTION in order to clearly specify the level of danger and possible injury or damage that may occur
if the device is misused.
Introduction
Safety Precautions
This symbol shows you what you must not do.

2
Use of the device could cause electronic medical devices to malfunction.
◆ Do not use in conjunction with any medical electronic equipment, including:
pacemakers or other implanted electronic medical devices; artificial heart-lung machines or other electronic life-support medical devices, and electrocardiographs
or other worn electronic medical devices.
● The following individuals should not use the device.
Danger (regarding use and storage)
Doing so may cause an injury or the generation of heat.
● Do not use the device continuously for an overly long period (for example, through commercial use).
Doing so may cause an accident or other problems.
• If you have existing or suspected heart disease, or related disorders • If you have been diagnosed with loss of temperature sensation • If you are under a doctor’s care
• If you are prohibited from exercising by doctors • If you are a child or adolescent • If you have an acute disease • If you have tuberculosis • If you have a fever
• If you are suffering from hypertension • If you have an infectious disease • If you have a malignant tumor • If you have a blood disease • If you have blood clots
• If you have a febrile disease • If you have a visceral disease • If you have a skin disease • If you have an allergic constitution • If you have atopic dermatitis
• If you have skin problems • If you have sensitive skin • If you have unhealthy skin blemishes caused by physical irritation
• If you are experiencing skin irritation or redness due to sunburn • If you are severely fatigued • If you are physically unwell • If you are under the influence of alcohol
• If you have excessive myopia (-6D or higher). • If you have had an eye or face operation • If you have diseases of the eyes or face or you are under treatment;
• If you are pregnant, menstruating, or lactating • If you have capillary dilatation due to long-term use of steroid hormonal drugs or a liver disorder;
• If you take medication that induces drowsiness
Doing so may cause an accident or other problems.
• Cuts • Sites where surgery (including plastic surgery) was performed • Anywhere inside the mouth, around the pubic region, or any mucous membrane • Acne
• Sites where skin suffers from purulent inflammation • Sites with itchiness or a hot sensation • Swollen moles and viral warts • The Adam’s apple • Eyeballs
• The eyelids or around the eyes (except in Cool Mode)
* The LED light can be used over eyelids and around the eyes. Close your eyes and hold the device at least five cm away from the eyes.
* If you are uncertain as to whether it is safe to use the device, consult a physician prior to use.
WARNING (Use and storage)
● Do not use under the following conditions:
● Do not use the device on the areas indicated below or outside of specified areas.
Prohibition
Prohibition

3
WARNING (Use and storage)
● Do not use the device when an odor or abnormal
generation of heat is detected.
Failure to comply may cause the device to become damaged or
catch fire.
● Do not overuse the device.
For usage time and frequency, follow the instructions in the
User’s Manual.
Failure to comply may cause physical injury.
● Do not use the device for a long time over sites where the
skin is thin or sites above bones.
Failure to comply may cause skin problems or physical ailments.
● Do not use anywhere on the body except for the face.
Failure to comply may cause injuries.
● Do not use continuously on the same area except when in
Cool Mode. Be sure to move the device across the skin while
it is in use. Do not use on areas that cannot be reached by
the entire electrode head surface.
Failure to comply may cause burn injuries.
● Do not place the device near fire or flames, and do not
dispose of the device in a fire. Do not use or store in a
high-temperature area or if the device is hot.
Failure to comply may lead to the generation of heat, a fire, or explosion.
● Do not use the device near a flammable substance (such as
alcohol, thinner, benzene, nail polish remover, or spray).
Failure to comply may cause a fire, electric shock or other injuries.
● Do not use the device on individuals who are unable to
express their will or who have reduced skin sensitivity.
Failure to comply may cause an accident or an injury.
● Use by unattended children or individuals with
physical disabilities should be avoided. Minors should
use the device only under the supervision of a guardian
who has given their consent.
Failure to comply may cause injuries.
● Do not place heavy items on the device, drop the device
(especially during use), or otherwise subject the device
to a strong impact.
Failure to comply may cause an injury or a failure of the device.
● Do not use the device for any purpose other than
those stated in the User’s Manual.
Failure to comply may cause an injury or a failure of the device.
● Do not place the device in an unstable location. Do not
drop or strike.
Doing so may cause a failure of the device. An injury may also be
caused if the device is dropped on a foot or other exposed body
part.
Prohibition
Use is prohibited
when an abnormal odor
or excess heat is detected
Pumping
is prohibited
Dropping of
the device is
prohibited
User restrictions
Non-intended uses
are prohibited.

4
WARNING (Use and storage)
● Be sure to perform a pre-test before using the device for the first time.
Failure to comply may cause an accident or an injury.
● If you are currently undergoing dental treatment or have teeth fillings, choose a lower intensity level and apply the device on a different area.
You may feel strong irritation or discomfort by EMS on your cheeks or chin. If you feel strong discomfort, consult a physician.
● If water or foreign matter gets into the device (the main body, for example), immediately discontinue use and request an inspection.
Failure to comply may lead to a fire or electric shock.
● Do not use or store the device in the following locations:
• A high-humidity location such as a bathroom • Dusty areas • A location where there is exposure to direct sunlight
• A location where water or other liquids may splash on the device • A tilted location, or a location where there is vibration or shocks • An outdoor location
• A location where there are strong radio waves or magnetism • Locations that are accessible to children • A location where there is exposure to oil smoke or steam
• A location that may become hot, such as near a heating device (for example, a heater)
• A location with drastic temperature changes (for example, near an air conditioner or heater)
Failure to comply may lead to a fire, electric shock, malfunction, failure of the device, or other accidents.
Mandatory
Compliance
● Do not use or charge the device in the bathroom or near a bathtub, shower, sink, or other vessels filled with water.
Failure to comply may cause an electric shock, short circuit, fire, or failure of the device.
● Do not wet, wash, or immerse the device in water.
Failure to comply may cause an electric shock, short circuit, fire, or failure of the device.
● Do not disassemble, attempt to repair, or modify this device in any way.
Failure to comply may cause a fire, electric shock or other injuries.
Contact your local distributor for advice on repairing the device.
Exposure to water
is prohibited
Disassembly
is prohibited

5
WARNING (Use and storage)
● Do not leave the device near fire, in the hot sun, in a bathroom or other high-temperature/high-humidity location, or near combustible gas
or a flammable object. Do not dispose of the device in a fire or place it near fire or flames.
Do not use or charge in a high-temperature area or if the device is hot. Do not bring the device close to a heater.
The device features a built-in rechargeable battery. Failure to comply may cause the generation of heat, a fire, the explosion of the device, or failure of the device.
● Do not put the device into a microwave or pressure vessel.
Failure to comply may lead to the generation of heat, a fire, or explosion.
Combustion
warning
Explosion
ATTENTION (Use and storage)
● Refrain from the following acts.
Failure to comply may cause an accident, injury, or a failure of the device.
• Do not use the device if your skin is experiencing a rash, inflammation, itchiness, or other abnormalities.
• Do not use if damaged due to dropping or an impact with another item.
• Do not use the device continuously for an overly long period (for example, through commercial use).
● Do not press the device strongly or use it intensively on a single spot.
Pressing the device more strongly than necessary or using it intensively on a single spot may damage the skin.
● Avoid contacting the electrode head with any other metal surfaces or objects.
Failure to comply may cause the generation of heat, a fire, malfunctions, or damage to the device.
● Before use, check to make sure that the electrode is not cracked, deformed, or broken. Do not use the device if it is damaged or malfunctioning.
Failure to comply may cause skin problems or a malfunctioning of the device.
● Do not use the device in locations that are extremely hot or cold.
The recommended temperature range for the device’s usage environment is approximately 15 to 30°C.
● Do not use the device in locations that are unstable or where it could fall over easily.
Failure to comply may cause an injury or a failure of the device.
Prohibition

6
Mandatory
Compliance
●
Remove any accessories (necklace, belt, rings, earrings, etc.) before using the device.
Failure to comply may cause an accident or an injury.
●
Use only Level 1 for EMS upon first use and until you are accustomed to use.
Failure to comply may cause an accident or an injury.
●
Do not use the device outdoors.
Failure to comply may cause a failure or malfunction of the device. Outdoor use
is prohibited
ATTENTION (Use and storage)
● Do not wipe the device or charging base with alkali cleaning agent, alcohol, thinner, benzene, nail polish remover, or any other solvents.
Failure to comply may cause damage to the surface of the device.
● Do not use the device on pets.
Failure to comply may cause an injury.
● Do not leave the device on the floor or on top of furniture while it is switched on. Be sure to turn the device off after use.
Failure to comply may cause injury or damage the furniture.
● Do not allow the device to come into contact with another electronic appliance (electric blankets/bed sheets, heated tables, etc.) while the
power is on. Do not use with other electronic products at the same time.
Failure to comply may cause an injury or a failure of the device.
● Do not look directly into the LED light. When using the LED light to treat areas around the eyes and the eyelids, be sure to close your eyes
and keep the electrode head at least five cm away from the skin.
Failure to comply may cause injury to your eyes or skin.
● Do not use Cool Mode continuously.
If used for continuous treatments, the head will not fully cool.
To resume using the device, wait at least 30 minutes before proceeding.
Prohibition

7
Mandatory
Compliance
●
Reapply skin-care products or water during treatment to ensure that there is always some liquid between the electrode head and the skin.
If there is an insufficient amount of skin-care products or water, the stimulation will weaken, causing skin problems.
●
If you feel an unpleasant tingling on your skin, reduce the intensity level or move to another area. You could also moisten the skin with
skin-care products, water, or gel before using the device.
Failure to comply may cause skin damage.
●
Carefully clean the parts of the device that come into contact with the skin every time you use it and keep the device clean at all times.
Failure to comply may cause skin problems.
● If you begin feeling ill or if a skin abnormality appears during use, stop using the device immediately.
Check carefully to make sure there are no skin abnormalities before using the device. Stop using the device immediately if the treatment does not agree with your skin.
●
Stop using the device immediately if you feel any pain during use.
Failure to comply may cause an accident or skin problems.
●
Do not use the device in excess of the times shown below for each treatment:
Clean Mode: three minutes Moist Mode: five minutes Cool Mode: three minutes
Failure to comply may cause skin problems.
● Avoid using the device continuously on the same area of skin.
When using on the same area again, be sure to leave an interval of 24 or more hours between treatments. Excessive use may damage the skin.
The above recommendations are guidelines only; please observe your skin condition and use the device accordingly.
● After each use, be sure to turn the power off, remove dirt and other particles that have adhered to the device according to ‘After Treatment’
(page 27).
Failure to comply may cause skin problems or a malfunctioning of the device.
● Be sure to comply with the following items when using the device.
Failure to comply may cause an accident, injury, or a failure of the device.
• Do not use continuously on the same area.
• Use the device appropriately based on your skin condition.
• Do not use the device in combination with peelings, skin packs, or other treatments or after sunbathing.
ATTENTION (Use and storage)

8
WARNING (The power supply)
● Do not damage, modify, bundle, or otherwise apply
undue force to the AC adapter or USB charging cable.
Placing a heavy item on top of the AC adapter or USB charging cable,
or pinching them between other items, could damage them and cause
a fire or electric shock.
●
Do not pull the AC adapter or USB charging cable
when moving or lifting the device.
Failure to comply may cause an electric shock, short circuit, fire, or
disconnection.
●
Do not use if the AC adapter or USB charging cable is
damaged or if the wall socket is loose.
Failure to comply may cause an electric shock, short circuit, or fire.
Contact your local distributor for advice on repairing the device.
●
When disconnecting the AC adapter and USB charging
cable from an outlet, be sure to pull it out by holding the
power plug instead of the cord (Do not touch the metal
prongs). Do not insert or disconnect the plug with wet or
damp hands.
Failure to comply may cause an electric shock, short circuit, or fire.
●
When cleaning the device, be sure the power is switched off.
When the device is not in use, disconnect the AC adapter
and USB charging cable from the main body and the power
outlet. Do not insert or disconnect the plug with wet or
damp hands.
Failure to comply may cause an electric shock, short circuit, or fire.
Removing
the plug
●
Use at AC100-240V only to avoid a potential fire or
electrical shock hazard. Make sure the AC adapter and
USB charging cable are fully inserted into the electrical
outlet.
Failure to comply may cause a fire, electric shock, or a failure of the
device.
●
Be sure to use the dedicated USB charging cable supplied
with the product. Plug the AC adapter directly into a wall
outlet and do not overload the electric circuit.
Failure to comply may cause an electric shock, short circuit, fire, or failure
of the device.
●
Before charging the device, check to make sure the
charging terminal is not wet.
Failure to comply may cause an electric shock, short circuit, or fire.
●
In the unlikely event that an abnormality occurs,
immediately turn off the device.
Refrain from using the device if faulty operation, smoke, abnormal noises,
or odors are detected, or if it is otherwise operating in an abnormal state.
●
Stop using the device and turn it off when you feel an
earthquake or hear thunder. When the battery is charging,
disconnect the AC adapter and USB charging cable from
the device’s main body and the power outlet.
●
Do not plug the AC adapter into a power outlet when there
is gel or water (other liquid) in the charging base (do not
recharge the device).
Mandatory
Compliance
● Do not wet, wash, or immerse the AC adapter or USB
charging cable in water.
Failure to comply may cause an electric shock, short circuit, fire, or
failure of the device.
Use of a
damaged cable or
plug is prohibited
Do not pull
on the cord
to move the device
Careless or
reckless use
is prohibited
Exposure to water
is prohibited

9
Failure to comply may cause a fire, electric shock, or a failure of the device.
● Use at AC100-240V only to avoid a potential fire or electrical shock hazard.
Failure to comply may cause the generation of heat, a fire, or a malfunction of the device.
● Be sure to check the plug configuration and the voltage of the power outlet before use.
Mandatory
Compliance
WARNING
• The plug configuration and voltage may vary depending on the region and the type of accommodation. Always be sure to check for compatibility before using the device.
• For information about plug adapters, consult a travel agency or a consumer electronics retailer.
Combustion
warning
When Using Outside of Japan

10
Memo

11
Names and Functions of Components
Main Body
● Front view ● Side view
Electrode head
Level + button*
Clean Mode button
Cool Mode button
Charging terminal
Level indicator
Level - button*
Moist Mode button
Hand Electrode
(Silver rim on the rear)
* Press the +/- Level button
to select Ion or EMS level.

12
● Charging base ● Cotton stopper
(Attached to the electrode head of the main body
before packaging)
● AC adapter
* For dedicated use with this product. Do not use attachments other than those provided with the product.
* The design and specifications of the device and peripheral accessories are subject to change for improvement purposes without notice.
Functions
Accessories
● USB charging cable
(USB Type-C™)*
Use this stopper to apply cotton
to the electrode head (page 20).
●
RF (radio frequency): Warms the skin to the deep layers (stratum corneum)
to prepare a better condition for the treatment
●
Ion cleansing: Absorbs dirt that cannot be removed through normal face
washing with the power of ions
●
Ion Moisture: Incorporates ions with original waveforms, enabling skin-care
products to penetrate the skin (deep into the stratum corneum)
●
EMS: Stimulates the muscles with an electrical current
●
Photo: Treats your skin with LED Photo treatment
●
Cooling: Tightens skin with a cooling effect
● User’s Manual

13
Before Use
Charge the device
* If charging does not begin after approximately 10 seconds, check that the charging terminals of the main body and the charging base are aligned correctly
(such that the USB cable outlet in the charging base is at the back of the main body), and that the USB charging cable or AC Adapter connection is not loose.
Charging The level display lamps will blink white in order.
When charging
is complete The level display lamps will switch off. Remove the USB charging cable.
Charging time Approximately three hours (At an indoor temperature of approximately 25°C)
(Actual charging time will differ depending on the remaining battery level and the charging environment.)
Operating time Approximately 40 minutes; operating times will differ according to the usage mode, level, and environment.
Place the main body of the device on the charging base, which is connected to the USB charging cord, as shown in the diagram to begin charging.
Level indicator
Charging terminal
Charging terminal
USB cable outlet
Household power outlet
USB charging cable
AC adapter*
* The form presented here is for illustration purposes only.
Charging base

14
• Do not overload an electrical circuit with the AC adapter. Be sure the AC adapter is inserted directly into the wall outlet.
• Before charging, check that there is no liquid (water or gel, etc.) on the charging base. Liquid (water or gel, etc.) on the charging base during charging will cause the device to
malfunction.
• Fully charge the battery before using the device for the first time after purchasing.
• When using the device for the first time or when the device has not been used for an extended period of time, it is possible that you will be unable to use the device for very long even
with a full charge displayed.
In such a case, recharge the device before using it.
• Be sure to use the included AC adapter and USB charging cable.
• Do not recharge the device in locations where there are high temperatures or high humidity, such as bathrooms or washrooms.
ATTENTION

15
Modes
LED Lamps
Level indicator
Mode Indicator
Clean
Mode Button display
*1. If using your regular skin product, be sure it is water soluble. Do not use oil-based or
scrubbing skin products. Failure to comply may cause product malfunctions or skin
problems.
*2 See page 34.
• Be sure to move the device on your skin while using it. (except when using the
device in Cool Mode)
• Use of cotton in Moist mode is optional.
• The device and electrode head may get hot after using the Cool Mode. Do not
use Cool Mode continuous.
Allow the device to rest (with the power off) for at least half an hour after use.
The Clean Mode
display is lit.
The display for the
next recommended
mode blinks (page 17).
Standby
(State in which functioning
is suspended after
treatment on each mode
has been completed)
Level
Ion: 5 levels
Features
Level indicatorLED Lamps
LED (blue) lamp
Absorbs dirt that cannot be
removed through normal
face washing and tones your
skin.
Function
• RF
• Ion Cleansing
(+ Vibration)
• LED (Blue)
1–5 lamps
Recommended cosmetics
Operating time Frequency
Approximately three minutes
Treatments two to three times
per week
RF Booster Pad
Pore Refining Deep Cleansing*2
(or cotton and your regular skin
lotion*1)
(After one minute and 30 seconds, a
beeping sound will notify you that it is
time to begin treatment on the other
side of your face.)

16
Mode Button display
Moist
* Only the central electrode head
has cooling functions.
Cool
Moist Mode
display lamp
Cool Mode
display lamp
Level
Features
Level indicatorLED Lamps
N/A
Function
Recommended cosmetics
Operating time Frequency
Treatments two to three times
per week
Helps beauty ingredients to
penetrate into the stratum
corneum and moisturize
your skin
• RF
• Ion Moisture
(+ Vibration)
• EMS (low frequency waves)
Approximately five minutes
(After two minutes and 30 seconds,
a beeping sound will notify you that
it is time to begin treatment on the
other side of your face.)
Flawless Serum moisture or
RF Booster Pad Clear Deep
Moisture*2
(If moisture is insufficient, add
the skin lotion remaining in
the pouch.)
Level
Features
Level indicatorLED Lamps
Function
Recommended cosmetics
Operating time Frequency
Cooling treatment and LED
(Blue) improve skin elasticity
and skin texture.
• Cool
• LED (Blue)
Approximately three minutes
(After one minute and 30 seconds,
a beeping sound will notify you that
it is time to begin treatment on the
other side of your face.)
Everyday use is possible
LED (blue) lamp N/A N/A
Place directly on the skin.
(Using a milky lotion or other
skin-care products to
moisturize the skin before using
the device will increase
moisturizing.)
1–5 lamps
Ion
+
EMS
: 5 levels

17
Timer
A beeping sound will notify you half-way through the operating time.
Refer to pages 15 and 16 for operating times in each mode.
Standby Mode
When treatment on a certain mode is completed, the device will emit a rapid beeping sound and switch to Standby Mode. (State in which functioning is suspended)
Refer to pages 15 and 16 for operating times in each mode.
Briefly press the Mode button again to start the selected mode.
After treatment on Clean Mode has been completed, the Moist and Cool Mode lamp displays will blink, and when treatment on Moist Mode is completed, the Cool Mode lamp display
will blink.
Auto Power Off
If the device is not operated within approximately five minutes of going into Standby Mode, it will emit a beeping sound and switch off automatically.
When treatment on Cool Mode has finished, the power will turn off automatically.

18
Pre-testing on Skin
1Wash the inner side of your arm with soap and water,
then wipe dry with a towel.
Be sure to wipe the moisture off completely.
2
3
When using the device for the first time, always test for compatibility.
ATTENTION
● Be sure to perform a pre-test in order to prevent skin problems from occurring.
● If a rash, reddening, itchiness, stinging sensation, or other abnormality occurs at the pre-testing site, immediately stop
the pre-test.
● Check carefully to make sure there are no skin abnormalities before using the device. Stop using the device immediately
if the treatment does not agree with your skin.
Apply water or a gel/lotion that you already own to the skin
and use the device on Moist Mode Level 1 for approximately
three minutes (pages 19 to 23).
Make sure there is nothing unusual about your skin.
Continue to use the product only if you experience no reddening or burning sensation on your skin within 24 hours.

19
How to Use
Read the items below carefully before use and use only as directed.
Precautions
● Be sure to perform a pre-test before using the device for the first time (page 18).
● Be sure to move the device on your skin while using it. Using the device continuously on the same area may cause burns or other injuries.
(except when using the device in Cool Mode)
● The warmth of the RF (radio frequency) changes depending on the type of skin-care products used and the skin’s condition at the time
of treatment.
● Do not use this device around the eyes unless it is in Cool Mode.
* The LED light can be used around the eyes and eyelids. Close your eyes and hold the device at least five cm away from the skin.
● Do not look directly into the LED light.
● When holding the device, make sure that you are holding the hand electrode.
● Recommended environmental temperature: 15 to 30°C