YAMAN Photo PLUS Shiny User manual

To be retained
User’s Manual
Table of
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . 1
When Using Outside of Japan. . . . . . . . . . . 9
Names and Functions of Components. . . . 10
Before Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to Use . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
After Treatment . . . . . . . . . . . . . . . . . . . . . . 26
Additional Information . . . . . . . . . . . . . . . . 28
z Troubleshooting . . . . . . . . . . . . . . . . . . . 28
z Frequently Asked Questions . . . . . . . . . 30
z Product Specifications . . . . . . . . . . . . . . 31
After-sales Service. . . . . . . . . . . . . . . . . . . . 32
Home Beauty Device M18Photo PLUS Shiny

1
* ’Property damage’ refers to damage affecting dwellings, household belongings, or domestic animals and pets.
DANGER Improper use of this device poses a severe and likely risk of death or
serious injury.
WARNING
Failure to operate the device according to this type of precaution
could result in death or serious injury.
ATTENTION
Improper use of this device may result in an injury or a property
damage*.
This symbol shows you what you must do.
This symbol shows you what you must be careful with.
Thank you for purchasing this YA-MAN product.
• Please read this User’s Manual carefully for information on how to use the device properly and safely.
• After reading the contents hereof, be sure to keep this User’s Manual in an accessible location.
• Make sure to include this User’s Manual if you are transferring ownership of the device to another person.
z Classifications of Precautions z Symbols
• Read these Safety Precautions carefully before using the device.
• Use the device sensibly in accordance with the prescribed steps.
• Immediately discontinue use and arrange to have the device repaired if any abnormality occurs.
• Do not use the device in a defective state, as doing so could cause a physical harm to the user.
• The precautions listed in the User’s Manual are very important. For your safety, please follow them carefully.
• Precautions are classified as DANGER, WARNING, or ATTENTION in order to clearly specify the level of danger and possible injury or damage that may occur
if the device is misused.
Introduction
Safety Precautions
This symbol shows you what you must not do.

2
Failure to comply may cause electronic medical devices to malfunction.
 Do not use the device in conjunction with any medical electronic equipment, including:
pacemakers or other implanted electronic medical devices; artificial heart-lung machines or other electronic life-support medical devices; and
electrocardiographs or other worn electronic medical devices.
● The following individuals should not use the device:
DANGER (Use and storage)
Doing so may cause an injury or the generation of heat.
● Do not use the device continuously for an overly long period (for example, through commercial use).
Doing so may cause an accident or other problems.
• If you have been diagnosed with loss of temperature sensation • If you are under a doctor’s care • If you have existing or suspected heart disease, or related disorders
• If you are in a physical growth stage • If you have an acute disease • If you have tuberculosis • If you have a fever • If you are suffering from hypertension
• If you have an infectious disease • If you have a malignant tumor • If you have a blood disease • If you have blood clots • If you have a febrile disease
• If you have a visceral disease • If you have a skin disease • If you have an allergic constitution • If you have atopic dermatitis • If you have skin problems
• If you have sensitive skin • If you have unhealthy skin blemishes caused by physical irritation • If you are experiencing skin irritation or redness due to sunburn
• If you are severely fatigued • If you are physically unwell • If you are under the influence of alcohol • If you have excessive myopia (-6D or higher)
• If you have had an eye or face operation • If you have diseases of the eyes or face or you are under treatment • If you are pregnant, menstruating or lactating
• If you have capillary dilatation due to long-term use of steroid hormonal drugs or a liver disorder • If you take medication that induces drowsiness
Doing so may cause an accident or other problems.
• Cuts • Areas where surgery (including plastic surgery) was performed • Areas where cosmetic treatment was performed
• Anywhere inside the mouth, around the pubic region, or any mucous membrane • Acne • Areas where skin suffers from purulent inflammation
• Areas with itchiness or hot sensations • Swollen moles and viral warts • The Adam’s apple • Eyeballs • Upper eyelids (except in COOL Mode)
• Areas around the eyes (except in EYE CARE Mode and COOL Mode)
* The LED light can be used over the upper eyelids and around the eyes. Close your eyes and hold the device at least 5 cm away from the skin. Do not look directly into the LED light.
* If you are uncertain as to whether it is safe to use the device, consult a physician prior to use.
WARNING (Use and storage)
● Do not use under the following conditions:
● Do not use the device on the areas indicated below or outside of specified areas.
Prohibited
Prohibited

3
WARNING (Use and storage)
● Do not use the device when an odor or abnormal
generation of heat is detected.
Failure to comply may cause the device to become damaged or catch fire.
● Do not use the device for a long time over areas where the
skin is thin or areas above bones.
Failure to comply may cause skin problems or physical ailments.
● Do not use anywhere on the body except for the face.
Failure to comply may cause injuries.
● Do not use continuously on the same area except when in
EYE CARE or COOL Mode. Be sure to move the device across
the skin while it is in use. Do not use on areas that cannot be
reached by the entire electrode head surface.
Failure to comply may cause burn injuries.
● Do not place the device near fire or flames, and do not
dispose of the device in a fire. Do not use or store in a
high-temperature area or if the device is hot.
Failure to comply may lead to the generation of heat, a fire or explosion.
● Do not use the device near a flammable substance (such as
alcohol, thinner, benzene nail polish remover or spray).
Failure to comply may cause a fire, electric shock or other injuries.
● Do not use or store the device in the following locations:
• Dusty areas • A location where there is exposure to direct sunlight
• Uneven or unstable location, or a location where there is vibration or shocks
• An outdoor location • A location where there are strong radio waves or magnetism
• Locations that are accessible to children
• A location where there is exposure to oil smoke or steam
• A location with drastic temperature changes (for example, near an air conditioner
or heater)
Failure to comply may lead to a fire, electric shock, malfunction, failure of
the device or other accidents.
● Do not use the device on individuals who are unable to
express their will or who have reduced skin sensitivity.
Failure to comply may cause an accident or an injury.
● Use by unattended children or individuals with physical
disabilities should be avoided. Minors should use the
device only with the consent and under the supervision of
their parents.
Failure to comply may cause injuries.
● Keep the device, charging base, and USB cable away
from children and do not allow them to use the device.
Do not allow children to play with the device.
Failure to comply may cause an accident or an injury.
● Do not place heavy items on the device, drop the device
(especially during use) or otherwise subject the device to
a strong impact.
Failure to comply may cause an injury or a failure of the device.
● Do not use the device for any purpose other than
those stated in the User’s Manual.
Failure to comply may cause an injury or a failure of the device.
● Do not place the device on an unstable location. Do not
drop or strike.
Doing so may cause a failure of the device. An injury may also be
caused if the device is dropped on a foot or other exposed body part.
Prohibited
Use is prohibited
when an abnormal odor
or excess heat is detected
Shock
is prohibited
Dropping of
the device
is prohibited
User
restrictions
Non-intended
uses are
prohibited

4
WARNING (Use and storage)
● Be sure to perform a pre-test before using the device for the first time.
Failure to comply may cause an accident or an injury.
● If you are currently undergoing dental treatment or have teeth fillings, choose a lower intensity level and apply the device
on a different area.
You may feel strong irritation or discomfort due to the EMS effect on your cheeks or chin. If you feel strong discomfort, consult a physician.
● If water or foreign matter gets into the device (such as the main body), immediately discontinue use and request an inspection.
Failure to comply may lead to a fire or electric shock.
Mandatory
compliance
● Do not use or charge the device in the bathroom or near a bathtub, shower, sink or other vessels filled with water.
Failure to comply may cause an electric shock, short circuit, fire or failure of the device.
● Do not wet, wash or immerse the device in water.
Failure to comply may cause an electric shock, short circuit, fire or failure of the device.
● Do not disassemble, attempt to repair or modify this device in any way.
Failure to comply may cause a fire, electric shock or other injuries.
Contact your local distributor for advice on repairing the device.
Exposure
to water
is prohibited
Disassembly
is prohibited

5
WARNING (Use and storage)
● Do not leave the device near fire, in the hot sun, in a bathroom or other high-temperature/high-humidity location or near
combustible gas or a flammable object. Do not dispose of the device in a fire or place it near fire or flames. Do not use or charge in a
high-temperature area or if the device is hot. Do not bring the device close to a heater.
The device features a built-in rechargeable battery. Failure to comply may cause the generation of heat, a fire, the explosion of the device or failure of the device.
● Do not put the device into a microwave or pressure vessel.
Failure to comply may lead to the generation of heat, a fire or explosion.
Fire hazard
Explosion
CAUTION (Use and storage)
● Do not press the device strongly or use it intensively on a single area.
Pressing the device stronger than necessary or using it intensively on a single area may damage the skin.
● Avoid letting the electrode head come into a contact with any other metal surfaces or objects.
Failure to comply may cause the generation of heat, a fire, malfunctions or damage to the device.
● Before use, check to make sure that the electrode is not cracked, deformed or broken. Do not use the device if it is damaged or
malfunctioning.
Failure to comply may cause skin problems or a malfunctioning of the device.
● Do not use the device in locations that are extremely hot or cold.
The recommended temperature range for the device’s usage environment is approx. 15 to 30° C.
Prohibited

6
Mandatory
compliance
●
Remove any accessories (necklace, belt, rings, earrings, etc.) before using the device.
Failure to comply may cause an accident or an injury.
●
Use only Level 1 upon the first use and until you are accustomed to use.
Failure to comply may cause an accident or an injury.
●
Stop using the device immediately if you feel any pain during use.
Failure to comply may cause an accident or skin problems.
CAUTION (Use and storage)
● Do not wipe the device or charging base with solvents such as alcohol, thinner, benzene, nail polish remover, kerosene, chemicals or
polishing powder.
Failure to comply may cause a damage to the surface of the device.
● Do not use the device on pets.
Failure to comply may cause an injury.
● Do not leave the device on the floor or on top of furniture while it is switched on. Be sure to turn the device off after use.
Failure to comply may cause injuries or damages the furniture.
● Do not allow the device to come into a contact with another electronic appliance (electric blankets/bed sheets, heated tables, etc.)
while the power is on. Do not use with other electronic products simultaneously.
Failure to comply may cause an injury or a failure of the device.
● Do not look directly into the LED light. When using the LED light to treat areas around the eyes and the eyelids, be sure to close your eyes
and keep the electrode head at least 5 cm away from your skin.
Failure to comply may cause damage to your eyes or skin.
● Do not use COOL Mode continuously.
If used for continuous treatments, the head will not fully cool.
To resume using the device, wait at least 30 minutes before proceeding.
● Do not use the device in combination with peelings or skin pack treatments.
Failure to comply may cause skin problems.
Prohibited

7
Mandatory
compliance
●
Reapply skincare products or water during treatment to ensure that there is always some moistures between the electrode head and the skin.
If there is an insufficient amount of skincare product or water, the stimulation will become weaker, causing skin problems.
●
If you feel an unpleasant tingling on your skin, reduce the intensity level or move to another area. You could also moisten your skin with
skincare products, such as lotion, before using the device.
Failure to comply may cause damage to your skin.
●
Carefully clean the parts of the device that come into a contact with the skin every time you use it and keep the device clean at all times.
Failure to comply may cause skin problems.
● If you begin feeling ill or if a skin abnormality appears during use, stop using the device immediately.
Check carefully to make sure there are no skin abnormalities before using the device. Stop using the device immediately if the treatment does not agree with your skin.
●
Be sure to use the device only for the following lengths of time.
[Daily Care]
• DAILY Mode: up to 3 minutes per treatment, once a day
[Weekly Care]
• CLEAN Mode: up to 3 minutes per treatment, once a day, 2 to 3 times a week
• DYHP Mode: up to 5 minutes per treatment, once a day, 2 to 3 times a week
• EYE CARE Mode: up to 2 minutes per treatment, twice a day, 5 times a week
• COOL Mode: up to 3 minutes per treatment, once a day, 2 to 3 times a week
Do not use Daily Care and Weekly Care (except in EYE CARE Mode) on the same day.
● Avoid using the device continuously on the same area of skin (except when in EYE CARE Mode).
When using on the same area again, be sure to leave an interval of 24 hours or more between treatments.
Excessive use may damage the skin.
The above recommendations are merely guidelines. Please observe your skin condition and use the device accordingly.
● After each use, be sure to remove dirt and other particles that have adhered to the device according to ‘After Treatment’ (page 26).
Failure to comply may cause skin problems or a malfunctioning of the device.
CAUTION (Use and storage)

8
WARNING (Power supply)
● Do not damage, modify or bundle the USB charging cable.
Do not place heavy objects on the USB charging cable or allow it to get
pinched in between other objects as this may damage the cable and
cause a fire or electrical shock hazard.
●
Do not pull the USB charging cable when moving or lifting
the device.
Failure to comply may break the cable or cause an electric shock, short
circuit or fire.
●
Do not use the device if the USB charging cable is
damaged or if the USB port is loose.
Failure to comply may cause an electric shock, short circuit or fire.
Contact your local distributor for advice on repairing the device.
●
When unplugging the USB charging cable from the device
and the USB port, do so by gripping the USB plug (do not
touch the metal parts). Do not insert or disconnect the plug
with wet or damp hands.
Failure to comply may cause an electric shock, short circuit or fire.
●
When cleaning the device, be sure the power is switched off.
When the device is not in use, disconnect the USB charging
cable from the device. Do not insert or disconnect the plug
with wet or damp hands.
Failure to comply may cause an electric shock, short circuit or fire.
Removing
the plug
●
Make sure that the USB charging cable is fully inserted
into the USB port.
Failure to comply may cause a fire, an electric shock or a failure of the
device.
●
Be sure to use the dedicated USB charging cable supplied
with the product. Plug the AC adapter (commercially
available) directly into a wall outlet and do not overload
the electric circuit.
Failure to comply may cause an electric shock, short circuit, fire or failure
of the device.
●
Before charging the device, check to make sure there is no
lotion on the charging terminal.
Failure to comply may cause an electric shock, short circuit or fire.
●
In the unlikely event that an abnormality occurs, turn off
the device immediately.
Refrain from using the device if faulty operation, smoke, abnormal
noises, or odors are detected or if it is otherwise operating in an
abnormal state.
●
When you feel an earthquake or hear a thunder, stop using
the device and turn it off. If the device is charging, remove
the USB charging cable from the device.
Mandatory
Compliance
● Do not wash or submerge the USB charging cable in
water.
Failure to comply may cause an electric shock, short circuit, fire or a
failure of the device.
Use of a damaged
cable or plug
is prohibited
Moving the device
by pulling its cords
is prohibited
Careless or
reckless use
is prohibited
Exposure
to water
is prohibited
●
Do not plug the AC adapter (commercially available)
into a power outlet or charge the device when there is
lotion or other liquid in the charging base. Prohibited

9
Failure to comply may cause a fire, electric shock or a failure of the device.
● Use only with a 5 V DC USB power supply.
Failure to comply may cause the generation of heat, a fire, or a malfunction of the device.
● Be sure to check the plug configuration and the voltage of the power outlet before use.
Mandatory
compliance
WARNING
• The plug configuration and voltage may vary depending on the region and the type of accommodation. Always be sure to check for compatibility before using the device.
• For information about plug adapters, consult a travel agency or a consumer electronics retailer.
Fire hazard
When Using Outside of Japan

10
Names and Functions of Components
Main Body
● Front view ● Back view
Electrode head
Power/Level button
Charging terminal
Mode button
Remaining battery level indicator
Hand Electrode
LED Lamps
Mode lamp
Level indicator

11
● Charging base ● Cotton stopper
(attached to the electrode head of the main body when packaged)
* For use exclusively with this product. Do not use attachments other than those provided with the product.
* The design and specifications of the device and peripheral accessories are subject to change for improvement purposes without notice.
Functions
Accessories
● USB charging cable
(USB Type-C™)
Use this stopper to apply a cotton to the electrode head (page 18).
One short beep will sound to indicate the half-way point in the operating time.
Refer to pages 16 and 17 for each mode’s operating time.
Timer
When treatment in a certain mode is completed, the device will emit rapid beeping sounds and the following mode indicator flashes (Standby Mode indicates operation has stopped).
Refer to pages 16 and 17 for each mode’s operating time.
Briefly press the mode button again to start the mode that was flashing.
When treatment in COOL Mode has finished, the device will emit rapid beeping sounds and the power will switch off automatically without the device going to Standby Mode.
Standby Mode (only if Weekly Care is selected)
If the device is not used within approx. 5 minutes of going into Standby Mode, it will emit beeping sounds and switch off automatically.
Auto Power-off

12
Before Use
Charge the device
* If charging does not begin after about 10 seconds, check that the USB charging cable and the AC adapter (commercially available) are connected properly.
To begin charging, place the main body of the device on the charging base that is connected to the USB charging cord, as shown in the diagram.
Using a household power outlet
Remaining battery level indicator
Charging terminal
Charging terminal
Charging terminal
Household
power outlet
USB charging cable
AC adapter*
* Not included with the device.
Charging base
Using a computer
Remaining battery level indicator
Charging terminal
Charging terminal
Charging terminal
USB charging cable
Charging base

13
• Do not overload an electrical circuit with the AC adapter (commercially available). Be sure the AC adapter is inserted directly into the wall outlet.
• Fully charge the battery before using the device for the first time.
• When using the device for the first time or when the device has not been used for an extended period of time, it is possible that you will be unable to use the device
for very long even with a full charge displayed. In such cases, recharge the device before using it.
• Use only the enclosed USB charging cable.
• Do not recharge the device in locations where there are high temperatures or a high degree of humidity, such as bathrooms or washrooms.
ATTENTION
Charging The remaining battery level indicator flashes in white.
When charging
is complete The remaining battery level indicator lights up in white for 5 seconds and then turns off.
Charging time Approx. 3 hours (room temperature approx. 25° C)
The actual charging time will differ depending on the remaining battery level, the charging environment, and the AC adapter (commercially available) being used.
Operating time Approx. 30 minutes (at the maximum power in DYHP Mode).
The actual charging time will differ depending on the remaining battery level, the charging environment, and the AC adapter (commercially available) being used.
The battery is sufficiently charged.
White light
The battery level is low.
Red flash Charge the battery.
Red light
Remaining battery level indicator
You can check the remaining battery level with the remaining battery level indicator.

14
Pre-testing on skin
1Wash the inner side of your arm with a soap and water,
then wipe dry with a towel.
Be sure to wipe the moisture off completely.
2
3
When using the device for the first time, always test for its compatibility with your skin.
ATTENTION
● Be sure to perform a pre-test in order to prevent skin problems from occurring.
● If a rash, redness, itchiness, stinging sensation, or other abnormality occurs at the pre-testing area, immediately stop the
pre-test.
● Check carefully to make sure that there are no skin abnormalities before using the device. Stop using the device immediately
if the treatment does not agree with your skin.
Apply your regular skin lotion to your skin and use the device
in DYHP Mode on level 1 for approx. 5 minutes (page 19).
Make sure you are experiencing no skin abnormalities.
Continue to use the product only if you experience no redness or burning sensation on your skin within 24 hours.

15
How to Use
Read the items below carefully before use and use only as directed.
Precautions
● Be sure to perform a pre-test before using the device for the first time (page 14).
● Be sure to move the device on your skin while it is in use. Using the device continuously on the same area may cause burns or other injuries.
(except in EYE CARE Mode and COOL Mode)
● The warmth of the RF (radio frequency) changes depending on the type of skincare products used and the skin’s condition at the time of treatment.
● Do not use on the upper eyelids (except in COOL Mode) or around the eyes (except in EYE CARE Mode and COOL Mode).
* The LED light can be used over the upper eyelids and around the eyes. Close your eyes and hold the device at least 5 cm away from your skin. Do not look directly into the LED light.
● When holding the device, make sure that you are holding the hand electrode.
● Recommended environmental temperature: 15 to 30° C

16
Modes
DAILY
Mode Function Cotton Operating
time Level Recommended frequency
• EMS
• Iontophoresis
• LED (Red)
Without a cotton
pad
Approx.
3 minutes 3 levels Every day*2
CLEAN
• RF
• Ion conduction
• Vibration
(only during ion emission)
Approx.
3 minutes 3 levels
2 to 3 times
per week
DYHP
Approx.
5 minutes
EYE CARE
• RF
• DYHP
• LED (Red)
Approx.
2 minutes 3 levels
Daily Care
Weekly Care
With a cotton pad
Either with or
without a cotton
pad
Without a cotton
pad
3 levels
• RF
• Micro-currents
Recommended cosmetics*1
Skin lotion or serum
Skin lotion
Serum or sheet mask
Serum for the eye area 2 to 3 times
per week*3

17
• Cool down
• LED (Blue)
*1 If using your regular skincare product, be sure it is water soluble. Do not use oil-based or scrubbing skincare products.
Failure to comply may cause product malfunctions or skin problems.
COOL
–
Weekly care
Place directly on the skin*4
*2 Do not use on the same day as Weekly Care Mode (except in EYE CARE Mode).
*3 If you are concerned about dryness of the skin around the eyes, we recommend using the device 5 times a week.
*4 We recommend using the device after moisturizing your skin with a milky lotion or other skincare products.
Mode Function Cotton Operating
time Level Recommended frequency
Without a cotton
pad
Approx.
3 minutes
Recommended cosmetics*1
Treatments
2 to 3 times
a week

18
How to attach a cotton pad to the electrode head
1Remove the cotton stopper
from the electrode head.
2Place a piece of cotton on top of the electrode head and press the cotton stopper down over the cotton.
• If the cotton stopper does not fit properly on the electrode head, please use a larger and thinner piece of cotton. Because thick cotton pads are difficult to fix in place,
split them in half before use.
• If the cotton pad is too thick, the thermal action of the RF treatment may be adversely affected and you will feel less heat.
• If the cotton pad becomes dry, add more skin lotion.
ATTENTION
3Apply your regular skin lotion to the cotton pad.
• Make sure the skin lotion covers the entire surface of the electrode head.

19
Basic method of use
1Remove makeup and gently cleanse your face.
• Remove oil and dirt from your skin so that it is in a clean condition prior
to a treatment.
2Attach cotton pad to the electrode head
if necessary and apply skin lotion to the
cotton pad.
* COOL Mode can be used over makeup.
3Turn on the device
Hold down the Power/Level button (hold down the button for approx. 3 seconds
or longer).
The device will emit a beeping sound, the mode button (DAILY) lights up, and
DAILY Mode starts.
Refer to page 18 for information on how to attach
the cotton pad. Mode button
Power/Level button