SPC-Series Operation Manual
SPC-Series Operation Manual
YCO-1092-01-02YCO-1092-01-02
1. Remove rectangular plug at the rear of the scale to expose 4 place dip switch shown below.
High(H)
Low (L)
(Example: Decimal oz/g mode with lb mode displayed at power up, Auto-off feature disabled)
a. Dip Switch functions:
1) Switch 1 and 2 2) Switch 3 controls 3) Switch 4 controls
control unit of measure gram/lb preference Auto-offfeature
at power up
2. Set switch to desired combination and replace rectangular plug.
B. Gross Weighing
1. Remove any load from the scale platform.
2. Depress "ON/ZERO/TARE" key to turn on scale. The display will briefly show all digital
segments (figure eights), then the scale will automatically reset to zero.
3. If the scale is already on, simply depress the "ZERO/TARE" key to reset display to zero.
4. Place item(s) to be weighed on the scale platform. Weight displayed will be gross weight.
C. Net Weighing (with automatic tare)
1. Repeat steps 1 to 3 in Gross Weighing above.
2. Place container on the platform and depress the "ZERO/TARE" key. The weight of the
container (tare weight) will be deducted and the display will show zero.
3. Place item(s) to be weighed in the container. Weight displayed will be net weight.
4. Should you need to display gross weight, depress and hold "N/G" key. Weight displayed will
be gross weight.
5. To clear the tare entry and return to zero, remove any load from the scale platform, and
depress the "ZERO/TARE" key.
D. Batch Weighing (separate weighing of several items)
1. Repeat steps 1 to 3 in Gross Weighing above.
2. Place container on the platform and depress the "ZERO/TARE" key. The weight of the
container (tare weight) will be deducted and the display will show zero.
3. Place the first item in the container until desired weight is reached. Depress the "ZERO/
TARE"key.
4. Place the second item in the container until desired weight is reached. Depress the "ZERO/
TARE" key. Repeat steps 3 and 4 as necessary.
INTRODUCTION
It only takes a few minutes to learn how to use your new *Accu-Weigh scale. Please read over
the following instructions carefully. They will assist you in understanding the various controls
and operation of the *Accu-Weigh SPC series scale.
FEATURES AND CONTROLS
The SPC series scale has several controls:
A. The scale may be turned on by depressing the "ON/ZERO/TARE" key.
B. The scale may be turned off by depressing the "lb/g" key and the "N/G" key simultaneously.
C. The "ZERO/TARE" activates the tare function. When the "ZERO/TARE" key is depressed
the digital display will read "tare" before resetting to "0".
D. The "lb/g" key selects the unit of measure.
E. The "N/G" key, when held down will indicate gross weight during a net weighing procedure.
F. Automatic Shut-Off: When enabled the scale will automatically shut off after two minutes
of non-use (thirty seconds when zero is indicated on digital display).
WEIGHING PROCEDURES
A. Set scale to desired unit of measure setting:
W
Net/Gross Wt.
Switch Key
Net/Gross
Wt.Indicator Digital
Display
Unit of
Measure
Indicator
Power On
Zero/Tare
Key
Unit of
Measure
Switch Key
2
1H
HLH HL LL
Switch No.
Fractional oz / g
Decimal oz / g
Decimal lb / g
Gramonly
(lbdisabled)
3
H
L
Switch No.
Lbmode
Grammode
4
H
L
Switch No.
Auto-offdisabled
Auto-offenabled
(scale will shut off in 2 minutes
of non-use with weight on
platform or 30 seconds with no
weight on platform)
1 2 3 4
2 3
