Yealink T58V User manual

2
2018-02-14
Table of Contents
Introduction ..................................................................................................................................................3
Before You Begin........................................................................................................................................... 3
Get Help ........................................................................................................................................................ 3
Scenario.........................................................................................................................................................4
Configuring Yealink T58V .......................................................................................................................... 4
Configuring Algo 8061 IP Relay Controller................................................................................................ 5
Configuring Algo 8039 SIP Video Intercom............................................................................................... 6
Configuring 8036 SIP Multimedia Intercom.............................................................................................. 8

3
2018-02-14
Introduction
This guide outlines the configuration required to set up a video call to/from Yealink T58V Smart
Media phone to the Algo 8036 SIP Multimedia Intercom or 8039 SIP Video Intercom. Also covered
are instructions to step up the optional Algo 8061 IP Relay Controller, where the telephone
keypad can activate a relay for releasing a locked door/gate during an intercom call.
The 8036 and 8039 are designed for indoor or outdoor public access locations to provide
enhanced communication and support for guests and visitors. Applications include unattended
lobbies, security monitoring, employee access, visitor greeting, video calling, enhanced courtesy
phone, multi-tenant gate or entrance, guest service, and visitor assistance kiosk.
For further User Guide information please refer to: 8036 SIP Multimedia Intercom, 8039 SIP Video
Intercom or 8061 IP Relay Controller.
Note: Any of the other audio-only Algo SIP intercoms, such as the 8028 or 8201, are compatible
using Yealink phones.
Before You Begin
This guide covers the steps for configuring the Algo 8036 SIP Multimedia Intercom and 8039 SIP
Video Intercom for one-way video calls with Yealink T58V.
Firmware used during testing:
Yealink T58V - 58.80.0.10
Algo 8036 –1.5.6
Algo 8039 –1.5.6
Algo 8061 –2.7.3
Get Help
For more information about installing, configuring, and administering Yealink products, refer to
Documents and Downloads at Yealink Support. For technical questions about the Algo products,
please contact Algo support: at 604-454-3792 or [email protected].

4
2018-02-14
Scenario
This example shows how to configure the 8036 and/or 8039 for one-way video communication
with Yealink T58V Smart Media Phone. Configuring the 8061 IP Relay Controller for door control
is also covered.
Configuring Yealink T58V
1) To view the phone's IP address, navigate to the Settings menu on the phone, under
Status, click General
2) To access the configuration panel, open an empty web browser, enter the device’s IP
address in the address field, and press Enter
3) In the web interface enter the username and password to log in (default is admin/admin)
4) Click on Account tab, then Register. Make sure Line Active setting is enabled, enter the
desired values in Label, Display Name, Register Name, User Name, and Password.
Moreover, enter the information for SIP Server 1. Contact your system administrator for
more information. Click Confirm at the bottom of the page to save the changes

5
2018-02-14
Configuring Algo 8061 IP Relay Controller
1) To configure the 8061, open an empty web browser, enter the device’s IP address in the
address field, and press Enter
2) To find the device’s IP address, please refer to the user guide available at:
http://www.algosolutions.com/8061/guide
3) In the web interface, enter the password to log in (default password is algo)
4) There is no need to do a separate SIP Server registration, in this scenario. Leave the SIP
Domain, Extension, Authentication ID and Authentication Password blank
5) Navigate to Basic Settings, Door Control tab. Ensure Door Control Link is enabled and
enter a password for Door Control Password. Click save

6
2018-02-14
6) It is recommended to have a Static IP Address assigned to this device, as it will need to be
entered on the 8036 and/or 8039. Save the changes
Configuring Algo 8039 SIP Video Intercom
1) To configure the 8039, open an empty web browser, enter the device’s IP address in the
address field, and press Enter
2) To find the device’s IP address, please refer to the user guide available at:
http://www.algosolutions.com/8039/guide
3) In the web interface, enter the password to log in (default password is algo)
4) Click on Basic Settings tab and then SIP tab. To register the 8039 with the SIP Server enter
the domain name or IP address in the SIP Domain (Proxy Server) field. Enter a unique SIP
Extension, Authentication ID and Authentication Password. Lastly, enter the Extension
to Dial (this is dialed when Call button is pressed). At the bottom of the screen click Save

7
2018-02-14
5) Navigate to Basic Settings tab, then Door Control tab. Enter the IP address (Network Door
Controller Address) and password (Network Door Controller Password) assigned to the 8061
previously. Save the changes

8
2018-02-14
Configuring 8036 SIP Multimedia Intercom
Note: Two-way video is not supported on the current firmware release.
1) To configure the 8036, open an empty web browser, enter the device’s IP address in the
address field, and press Enter
2) To find the device’s IP address, please refer to the user guide available at:
http://www.algosolutions.com/8036docs
3) In the web interface, enter the password to log in (default password is algo)
4) Click on Basic Settings tab and then SIP tab. To register the 8036 with the SIP Server enter
the domain name or IP address in the SIP Domain (Proxy Server) field. Enter a unique SIP
Extension, Authentication ID and Authentication Password. At the bottom of the screen
click Save.
5) Navigate to Basic Settings tab, then Door Control tab. Enter the IP address (Network Door
Controller Address) and password (Network Door Controller Password) assigned to the
8061 previously. Save the changes

9
2018-02-14
6) To configure the user interface, buttons, and functions, please see the Quick Start guide
available at: www.algosolutions.com/8036docs