Yealink W52H User manual

Quick Start Guide(V81.10)
IP DECT Phone
W52P & W52H
www.yealink.com Applies to firmware version 25.81.0.10 or later.

The following items are included in your W52P package:
Packaging Contents
Base Station Charger Cradle
Belt Clip
W52H Handset
Ethernet Cable
The following items are included in your W52H package:
Charger Cradle Power Adapter Two Rechargeable
Batteries
Belt Clip
Two Rechargeable
Batteries
W52H Handset
Two Power Adapters
(Optional)
1
Quick Start Guide
Packaging Contents
Note: Yealink W52P IP DECT phone consists of one Base for W52P/W56P and
one W52H Handset.
Note: We recommend that you use the accessories provided or approved by
Yealink. The use of unapproved third-party accessories may result in
reduced performance.

1. Connect the network and power for the base station in
one of the following ways, as shown below:
Assembling the Phone
a. AC Power Option
2. Connect the charger cradle, as shown below:
3. Insert the batteries into the handset, as shown below:
4. Charge the handset, as shown below:
b. PoE (Power over Ethernet) Option
IEEE 802.3af compliant
PoE Hub/Switch
2
Assembling the Phone
Note: The IP DECT phone should be used with Yealink original power adapter
(5V/600mA) only. The charging status of the handset is indicated on the
top right-hand corner of the LCD screen.

Easy Registration:
Normal Registration:
Getting Started
3
Shortcuts
This helps you get quick access to features by pressing the shortcut keys
directly without scrolling through the menu. You can press the following
predefined shortcuts to access some frequently used features when the
handset is idle:
Press to access the call history.
Press to check the line status.
Press to place an internal call.
Press to decrease the ringer volume.
Press to access the directory.
Press to increase the ringer volume.
Getting Started
Handset Registration
When the handset LCD screen prompts “Press base paging 2s then press
Reg.”, long press on the base station till the registration LED flashes.
There are two methods to register a new handset:
1.Press the OK soft key on the handset, and then select Register Handset.
2.Select the desired base and then press the OK soft key. The handset
begins searching the base.
3.Press the OK soft key after searching a base successfully.
1.Press the Reg soft key on the handset to register quickly.
You can register up to 5 handsets to one base station. Each handset can be
registered to 4 different base stations.
Press one or more times to switch among different input modes or
enter “#”.
Press to select the special characters or enter “*”.
Press a digit key one or more times to enter the desired character or digit.
Press the Del soft key to delete entered characters.
Press the Save soft key to accept the change or to cancel.
Entering and Editing Data

Network Settings
DHCP: By default, the base station attempts to contact a DHCP server in
your network to obtain the valid network settings, e.g., IP address,
subnet mask, gateway address and DNS address.
Static: If the base station cannot contact a DHCP server for any reason,
you need to configure the IP address, subnet mask, gateway
address, primary DNS address and secondary DNS address for the
base station manually.
You can configure the base station to obtain network settings in one of the
following ways:
4
To configure the network parameters for the base station manually:
1.Press the OK key to enter the main menu, and then select Settings->
System Settings->Network (default PIN: 0000)->Basic.
3.Press to select the corresponding IP address mode.
2.Select the desired IP address mode from the IP Mode field.
4.Make the desired changes.
5.Press the Save soft key to accept the change.
Note: The IP DECT phone supports either or both IPv4 and IPv6 addresses
modes, but IPv6 is disabled by default.
Wrong network settings may result in inaccessibility of your DECT phone
and may have an impact on the network performance. For more
information on these parameters, contact your system administrator.
You can also press the OK key to enter the main menu, and then select
Settings->Registration->Register Handset and repeat steps 2-4 to
register multiple base stations.
Note: After the success of registration, the handset LCD screen prompts
“Handset Subscribed” and “Base NO. (last 4 characters of connected
Base’s MAC address)” .
If the handset LCD screen prompts “Searching for Base”, please check if
your base station is powered on.
4.Enter the base PIN (default: 0000), and then press the Done soft key to
complete registration.

Turning Handset On/Off
To turn the handset on, do one of the following:
Place the handset in the charger cradle. The handset will be turned on
automatically.
To turn the handset off:
Locking/Unlocking Keypad
Handset Name
1.Press the OK key to enter the main menu, and then select Settings->
Handset Name .
3.Press the Save soft key to accept the change.
Silent Mode
Press or when the handset is idle or ringing to adjust the ringer
volume.
Volume Adjustment
Press or during a call to adjust the receiver volume of
speakerphone/earpiece/earphone.
Press , then the LCD screen lights up.
Long press to turn the handset off.
Long press when the handset is idle to switch the silent mode to On.
Long press when the handset is idle to lock the keypad.
Long press again to switch the silent mode to Off.
Long press again to unlock the keypad.
To rename the handset:
2.Edit the value in the Rename field.
Basic Operations
Handset Settings
5

6
Ring Tones
4.Press the Save soft key to accept the change.
Local Directory
To add a contact:
1.Press the OK key to enter the main menu, and then select Directory.
3.Enter the desired value in the Name, Number and Mobile field
respectively.
2.Press the Options soft key, and then select New Contact.
4.Press the Save soft key to accept the change.
To edit a contact:
1.Press the OK key to enter the main menu, and then select Directory.
3.Press or to select the desired ring tone.
2.Press or to highlight the desired entry.
3.Press the Options soft key, and then select Edit.
4.Edit the value in the Name, Number and Mobile field respectively.
5.Press the Save soft key to accept the change.
To delete a contact:
1.Press the OK key to enter the main menu, and then select Directory.
3.Press the Options soft key, and then select Delete to delete the selected
entry.
To assign a speed dial number:
2.Press or to highlight the desired entry.
2.Press or to highlight the Intercom Call option or the desired line.
1.Press the OK key to enter the main menu, and then select Settings->
Audio->Ring Tones->Melodies.
1.Press the OK key to enter the main menu, and then select Settings->
Telephony->Speed Dial.

Placing Calls
To place a call from the local directory:
To place a call from the call history:
1.Press the History soft key when the handset is idle, and then select the desired
call history list.
To place a call directly:
1.Press when the handset is idle.
Enter the desired number when the handset is idle.
2.Press or to highlight the desired entry, and then press or to
dial out using the default line.
If multiple numbers for the contact are stored, press or to
highlight the desired number, and then press or again to dial out
using the default line.
7
2.Press or to highlight the desired entry, and then press or
to dial out using the default line.
2.Press or to highlight the desired digit key, and then press the
Assign soft key.
3.Press or to highlight the desired entry, and then press the OK soft
key.
If both the office number and mobile number are stored, press or
to highlight the desired number, and then press the OK soft key again.
Basic Call Features
Press to enter the pre-dialing screen.
Enter the desired number using the keypad.
If there are multiple lines assigned to your handset as outgoing lines,
press the Line soft key to select the desired line. If you do not select a
line, the handset uses the default outgoing line to dial out.
2.Press , or to dial out.
1.Do one of the following:

To place a call using the speed dial key:
Long press the speed dial key to call the preset number directly.
Answering Calls
To answer a call, do one of the following:
Press the Accept soft key.
Ending Calls
Press .
To place a call from the redial list:
1.Press when the handset is idle.
2.Press or to highlight the desired entry, and then press or .
Press .
Press .
Call Hold and Resume
To place a call on hold:
To resume a call, do one of the following:
If there is only a call on hold, press the Resume soft key.
Press the Options soft key during a call, and then select Hold.
Call Mute
Press again to un-mute the call.
Press during a call to mute the call.
8
Press .
Note: You can ignore an incoming call by pressing the Silence soft key or reject an
incoming call by pressing .

If there are two calls on hold, press the Resume soft key to resume the
current call.
Press the Swap soft key to swap between calls.
Semi-Attended Transfer
Attended Transfer
Call Forward
Blind Transfer
Call Transfer
You can transfer a call in the following ways:
1.Press the Options soft key during a call, and then select Transfer.
1.Press the Options soft key during a call, and then select Transfer.
1.Press the Options soft key during a call, and then select Transfer.
2.Enter the number you want to transfer the call to.
To enable the call forward feature on a specific line:
1.Press the OK key to enter the main menu, and then select Call Features
->Call Forward.
2.Enter the number you want to transfer the call to.
3.Press the Transfer soft key.
2.Enter the number you want to transfer the call to.
4.Press the Transfer soft key after the call is answered.
2.Press or to highlight the desired line, and then press the OK soft
key.
9
4.Press the Transfer soft key when you hear the ring-back tone.
3.Press , or to dial out.
3.Press , or to dial out.

Always----Incoming calls are forwarded immediately.
Busy----Incoming calls are forwarded when the line is busy.
No Answer----Incoming calls are forwarded if not answered after a
period of time.
5.Enter the number you want to forward the incoming calls to in the Target
field.
6.Press the Save soft key to accept the change.
4.Select Enabled from the Status field.
For No Answer Forward, press or to select the desired ring time to
wait before forwarding in the After Ring Time field.
3.Press or to highlight the desired forwarding type, and then press
the OK soft key.
10

About us
Founded in 2001, Yealink, a leading provider of VoIP Phone and IP communication solutions,
has been focusing on VoIP products characterized by reliable quality, easy deployment and
affordable price for more than a decade. Today, customers from over 140 countries rely on
Yealink as the backbone of global collaboration to extend the value of network communications.
More about Yealink
Since 2001, Yealink has continued to develop state-of-the art, hi-tech VoIP communication
terminals that include IP video phones, IP phones and USB phones. With a worldwide market
in more than 140 countries, the company has also established a first-class international service
network.
Our priorities are quality, functionality, ease-of-use, customer support and competitive pricing.
To provide new solutions for the future in this fast-evolving sector, Yealink’s large, talented
and highly-experienced VoIP R&D team is totally committed to the pursuit of excellence.
To date, we have passed more than 80 interoperability tests and meet certification requirements
set by leading VoIP system and platforms. Yealink works in close partnership with T-Mobile,
Telefonica, Portugal Telecom and other leading telecommunication service providers.
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.
Web: www.yealink.com
Addr: 309, 3th Floor, No.16, Yun Ding North Road, Huli
District, Xiamen City, Fujian, P.R. China
Copyright
©2017 YEALINK(XIAMEN) NETWORK
TECHNOLOGY CO.,LTD. All rights reserved.
6
938818 300682