Yeastar Technology NeoGate TB400 User manual

How to Connect Yeastar TB BRI VoIP Gateway to 3CX
How to Connect Yeastar TB BRI VoIP
Gateway to 3CX
Version: 1.0
Date: 2015.07.28
Yeastar Information Technology Co. Ltd.

How to Connect Yeastar TB BRI VoIP Gateway to 3CX
Contents
1. Introduction.........................................................................................................1
2. Connect 3CX Phone System to TB400..............................................................2
2.1 Create a SIPTrunk on 3CX.............................................................................2
2.2 Create a VoIP Trunk on TB400........................................................................4
3. SIP to BRI............................................................................................................5
4. BRI to SIP............................................................................................................7

How to Connect Yeastar BRI VoIP Gateway to 3CX
1
1. Introduction
This guide shows you how to configure 3CX phone system to Yeastar BRI VoIP
gateway via SIP trunking. This guide has been tested with:
TB400 firmware version 18.18.0.3
3CX phone system v12.0.36097.670
Target：
After connecting Yeastar TB BRI gateway and 3CX phone system, physical trunk BRI
trunk will be extended on 3CX phone system.
The following features can be achieved:
Make outbound calls from 3CX via the BRI trunks of TB400.
Receive calls from BRI trunks of TB400 at 3CX.
Description：
IP address of 3CX phone system: 192.168.6.51
IP address of TB400: 192.168.6.137
A BRI line from provider is connected to TB00’s BRI port1.
BRI trunk number: 617839972
Figure 1 Connect 3CX Phone System and TB400

How to Connect Yeastar BRI VoIP Gateway to 3CX
2
2. Connect 3CX Phone System to TB400
2.1 Create a SIP Trunk on 3CX
1) Log in to the 3CX Management Console and click "Add VoIP Provider" node,
configure the VoIP Provider Wizard, then Click "Next".
Figure 3 Add VoIP Provider
Name of Provider: TB400
Country: Generic
Provider: Generic SIP Trunk
2) Enter the Yeastar TB400's IP and click "Next".
Note: the TB400 and 3CX Phone System must reside inside the same LAN.
Figure 4 VoIP Provider
3) Enter External Number and Authentication ID (You can enter any number that is
not the same with extension numbers of 3CX, take 9999 as an example here). And
click “Next”.
Note: "Maximum simultaneous calls " is four in the free version of 3CX. You can also
enter the number accordingly if you have bought license from 3CX.

How to Connect Yeastar BRI VoIP Gateway to 3CX
3
Figure 5 Configure SIP Trunk
4) Configure the default destination of inbound route to Digital Receptionist for the SIP
trunk and click “Next”.
Note: If you want to change the inbound route, you can double click the trunk you
want on the "Ports/Trunk Status" page after the SIP Trunk has been created.
Figure 6 Set Office Hours
5) Click "Skip" to finish the SIP trunk configuration.
Figure 7 VoIP Provider

How to Connect Yeastar BRI VoIP Gateway to 3CX
4
6) On "Ports/Trunk Status" page, we can check the trunk status.
Figure 8 SIP Trunk Status
2.2 Create a VoIP Trunk on TB400
Path: Gateway→VoIP Settings→VoIP Trunk
Figure 9 Create a Service Provider SIP Trunk on TB400
Trunk Type: Service Provider
Type: SIP
Provider Name: 3CX
Hostname/IP: fill in 3CX IP address, 192.168.6.51 the default port is 5060.
Save and apply the changes, we can check the status of this trunk, it should be OK.
Path: Status→System Status→IP Trunk Status
Figure 10 VoIP Trunk Status on TB400

How to Connect Yeastar BRI VoIP Gateway to 3CX
5
3. SIP to BRI
In this section, we introduce how to achieve making outbound calls from 3CX through
BRI trunk on TB400.
Figure 11 SIP to BRI
Step 1. Create one outbound route on 3CX.
To make external calls from 3CX through TB400’s BRI trunk, you need to create one
outbound route on 3CX.
Click "Add Outbound Rule" on 3CX.
Rule Name: Rule for TB400
Prefix: 9
Call from extension(s): 300-305, allow extension 300,301,302,303,304 and 305
to call out through this outbound rule.
Route: TB400
Strip: 1

How to Connect Yeastar BRI VoIP Gateway to 3CX
6
Figure 12 Outbound Route on 3CX
Step 3. Configure “sip_2_bri”Route on TB400.
Path: Gateway→Routes Settings→Route List
Figure 14 IP->Port Route
Route Name: give a name for the route, “sip_2_bri”.
Call Source: choose the VoIP trunk which is connected to 3CX, “SPS—3CX”.
Call Destination: choose the BRI trunk1.
Step 3. Test a call from 3CX.
Now, you can use 3CX phone system’s extension to make external calls through the
TB400’s BRI trunk 1. Do not forget to add digit 9 before the called number cause
prefix is set to 9 on 3CX outbound route. For example, if you want to call
15880270666, you need to dial 915880270666.

How to Connect Yeastar BRI VoIP Gateway to 3CX
7
4. BRI to SIP
In this section, we configure incoming calls to 3CX through BRI trunk on TB400.
Figure 15 BRI to SIP
Step 1. Create an inbound route on 3CX.
Click “Add DID/Inbound route” to configure the inbound route on 3CX.
Inbound route name: From TB400
DID/DDI number/mask: 9999, which is same with the trunk external number.
Available ports: TB400
Office Hours: Digital Receptionist

How to Connect Yeastar BRI VoIP Gateway to 3CX
8
Figure 16 Inbound Route on 3CX Phone System
Step 2. Configure the “bri_2_sip” Route on TB400.
Path: Gateway→Routes Settings→Route List
Figure 17 Port to IP Route Page
Route Name: give a name for the route, “bri_2_sip”.
Call Source: choose BRI trunk1.
Call Destination: choose the VoIP trunk which is connected to 3CX,
“ServiceProvider—3CX”.