Yeastar Technology TG Series User manual

NeoGate TA410/810
User Manual
Version 41.18.0.8
Yeastar Information Technology Co. Ltd

NeoGate TA410/810 User Manual
2/51
Table of Contents
Introduction ......................................................................................................................4
Application Description...................................................................................................5
Configuration Guide ........................................................................................................7
1. Login............................................................................................................................................7
2. Status...........................................................................................................................................9
2.1 System Status......................................................................................................................... 9
2.1.1 Port Status....................................................................................................................... 9
2.1.2 Network status ................................................................................................................10
2.1.3 System Info.....................................................................................................................10
2.2 Reports..................................................................................................................................10
2.2.1 Call Logs.........................................................................................................................11
2.2.2 System Logs...................................................................................................................11
2.2.3 Packet Tool .....................................................................................................................12
3. System....................................................................................................................................... 13
3.1 Network Preferences..............................................................................................................13
3.1.1 LAN Settings...................................................................................................................13
3.1.2 Service............................................................................................................................14
3.1.3 VLAN Settings.................................................................................................................14
3.1.4 VPN Settings...................................................................................................................15
3.1.5 DDNS Settings................................................................................................................16
3.1.6 Static Route....................................................................................................................17
3.2 Security Center ......................................................................................................................18
3.2.1 Security Center ...............................................................................................................18
3.2.2 Alert settings ...................................................................................................................20
3.2.3 AMI Settings....................................................................................................................22
3.2.4 Certificates......................................................................................................................23
3.2.5 Firewall Rules..................................................................................................................24
3.2.6 IP Blacklist ......................................................................................................................25
3.3 System Preferences ...............................................................................................................26
3.3.1 Password settings...........................................................................................................26
3.3.2 Date and Time.................................................................................................................27
3.3.3 Email Settings.................................................................................................................27
3.3.5 Firmware Update.............................................................................................................28
3.3.6 Backup and Restore........................................................................................................29
3.3.6 Reset and Reboot ...........................................................................................................29
4. Gateway..................................................................................................................................... 31
4.1 FXO Port List .........................................................................................................................31
4.1.1 FXO Port List ..................................................................................................................31
4.2 VoIP Settings .........................................................................................................................38

NeoGate TA410/810 User Manual
3/51
4.2.1 VoIP Server Settings........................................................................................................38
4.2.2 Dial Pattern Template ......................................................................................................41
4.2.3 SIP Settings ....................................................................................................................42
4.2.4 IAX Settings....................................................................................................................47
4.3 Gateway Settings...................................................................................................................48
4.3.1 General Preferences .......................................................................................................48
4.5 Advanced Settings..................................................................................................................48
4.5.1 Tone Zone Settings..........................................................................................................48
4.5.1 DTMF Settings................................................................................................................51

NeoGate TA410/810 User Manual
4/51
Introduction
NeoGate TA410/810 Analog VoIP Gateways are cutting-edge products that connect
legacy telephones, fax machines and PBX systems with IP telephony networks and
IP-based PBX systems. Featuring rich functionalities and easy configuration, NeoGate
TA410/810 is ideal for small and medium enterprises that wish to integrate a traditional
phone system into IP-based system. NeoGate TA helps them to preserve previous
investment on legacy telephone system and reduce communication costs significantly
with the true benefits of VoIP.
Features
●4/8 FXO ports
●Fully compliant with SIP and IAX2
●Flexible calling rules
● Configurable VoIP Server templates
●Codec: G.711 a/u-law, G.722, G.726, G.729a, GSM,ADPCM, Speex
●Echo Cancellation: ITU-T G.168 LEC
● Web-based GUI for easy configuration and management
● Excellent interoperability with a wide range of IP equipment
For more information, please click:
http://www.yeastar.com/Products/Products.asp#NeoGateTA
NeoGate TA410/810 FXO Gateway features 4, 8 FXO interfaces for connection of PSTN
and PBX extension and one 10/100 Mbps LAN port.
For more information about the NeoGate TA hardware specification and how to install the
NeoGate TA, please refer to the document below:
http://www.yeastar.com/download/PartI_NeoGate_TA_Series_Installation_Guide_en.pdf

NeoGate TA410/810 User Manual
5/51
Application Description
Connect IPPBX and NeoGate TA FXO Gateway
NeoGate TA FXO gateway is a solution to extend FXO ports for your IPPBX.
Two modes are available for you to connect IPPBX and NeoGate TA FXO gateway, we
call them VoIP mode and SPS (Service Provider SIP)/SPX (Service Provider IAX) mode.
VoIP Mode:
The FXO port will be registered as one the VoIP server's SIP extensions if "Enable
Register" is checked on VoIP Server template.Select the VoIP Server template on the
FXO port page, and fill in the information like SIP username and password. After
registeration, if you want to call from IPPBX, you should call the registered SIP account,
and NeoGate TA will route the call to the PSTN line.
SPS/SPX Mode:
If "Enable Register" is not checked, the FXO port will be registered as a SPS/SPX trunk to
the VoIP Server. One SPS/SPX trunk to NeoGate TA also should be created on the VoIP
Server. If you want to call from IPPBX, the number you dial should match the dial pattern
set on IPPBX outbound route. After receiving the call, NeoGate will forward it on the FXO
line to the destination number.
Figure II-1 Connect TA810 and IPPBX
For incoming calls from the PSTN to NeoGate TA, NeoGate TA will forward the call to a
configured SIP extension or to an inbound destination of IPPBX like IVR.

NeoGate TA410/810 User Manual
6/51
Connect NeoGate TA FXO Gateway and FXS Gateway
NeoGate TA FXO gateway can be connected to a FXS gateway using SPS/SPX Mode.
Imagine this, the FXO gateway is set up in Site A, and the FXS gateway in Site B. People
in Site B can make and receive calls using the local PSTN lines (which is connnected to
Site A’s provoider). With this solution, you can call a local number using a local PSTN line
wherever you are.
Figure II-2 Connect TA810 and FXS Gateway

NeoGate TA410/810 User Manual
7/51
Configuration Guide
1. Login
The NeoGate TA attempts to contact a DHCP server in your network to obtain valid
network settings (e.g., the IP address, subnet mask, default gateway address and DNS
address) by default.
Please enable DHCP Server in your network to obtain the NeoGate IP address.
How to check NeoGate TA IP address:
1. Download a DeviceFound tool from Yeastar website: FindTA.rar
2. Run the DeviceFound.exe software.
3. The detected NeoGate TA devices in the local network will appear in the window.
4. Find the TA device’s IP address by the device’s MAC address or the SN.
Figure III-1-1 Device Found Software
Logging On:
After entering the IP address in the Web browser, users will see a log-in screen.
Check the default settings below:
Username: admin
Password: password

NeoGate TA410/810 User Manual
8/51
In this example, the IP address is 192.168.10.125, the model is TA810.
Figure III-1-2 NeoGate TA Login page
Click "Login" to get the welcome page.
Figure III-1-3 Login NeoGate TA

NeoGate TA410/810 User Manual
9/51
2. Status
Click to check the status of NeoGate TA, including the system status and the
detailed reports.
2.1 System Status
In this page, we can check the status of the system, including trunk status, network status
and system information.
2.1.1 Port Status
Figure III-2-1FXO Port Status
Up/Down:
Up/Down
Description
Up
The FXO interface works well.
Down The FXO interface is broken.
VoIP Status:
Status
Description
OK Successful registration, trunk is ready for use
Unreachable
The trunk is unreachable.
Request Send
Registering.
Waiting for authentication Wrong password or user name.
Failed Trunk registration failed.
FXO Status
Hook
Description
Idle The FXO port is idle.
Busy The FXO port is busy.

NeoGate TA410/810 User Manual
10/51
Disconnect There is no line connected to the FXO port.
2.1.2 Network status
In this page, the IP address of LAN port will appear with their status.
Figure III-2-2 Network Status
If your VLAN or VPN are configured, you can check the status in this page also.
2.1.3 System Info
In this page, we can check the hardware/firmware version, or the disk usage of NeoGate
TA.
Figure III-2-3 System Info
2.2 Reports
In this page, we can check the call detailed log, system log, and use the packet tool to
debug the system when needed.

NeoGate TA410/810 User Manual
11/51
2.2.1 Call Logs
The call log captures all call details, including call time, caller number, callee number, call
type, call duration,etc. An administrator can search and filter call data by call date,
caller/callee, trunk, duration, billing duration, status, or communication type.
Figure III-2-4 Call Logs
2.2.2 System Logs
You can download and delete the system logs of NeoGate TA.
Figure III-2-5 System Logs
Options
·Enable Hardware Log
Save the information of hardware; (up to 4 log files)
·Enable Normal Log
Save the prompt information; (up to 16 log files)

NeoGate TA410/810 User Manual
12/51
·Enable Web Log
Save the history of web operations (up to 2 log files)
·Enable Debug Log
Save debug information (up to 2 log files)
2.2.3 Packet Tool
This feature is used to capture packets for technician. Integrate packet capture tool
“Wireshark” is integrated in NeoGate.
Users also could specify the destination IP address and port to get the packets.
Figure III-2-6 Packet Tool
·IP
Specify the destination IP address to get the packets.
·Port
Specify the destination Port to get the packets.

NeoGate TA410/810 User Manual
13/51
3. System
Click to access. In this page, we can configure the network settings, security
settings and some system preferences.
3.1 Network Preferences
3.1.1 LAN Settings
Figure III-3-1 Static IPAddress Mode
Table III-3-1 Description of LAN Settings
Items
Description
Hostname Set the host name for NeoGate TA
Static IP Address Set the NeoGate TA’s IP address as a static IP
IP Address Set the IP Address for NeoGate TA.It is recommended that you
configure a static IP address for NeoGate TA.
Subnet Mask Set the subnet mask for NeoGate TA
Gateway Set the gateway for NeoGate TA
Primary DNS Set the primary DNS for NeoGate TA.
Secondary DNS Set the secondary DNS for NeoGate TA
IP Address2
Set the second IP Address for NeoGate TA
Subnet Mask2
Set the second subnet mask for NeoGate TA
Figure III-3-2 DHCP Mode
Select DHCP mode to get network automatically from the local network.

NeoGate TA410/810 User Manual
14/51
Figure III-3-3 PPPoE
Fill in user name and password to access the Internet via PPPoE.
3.1.2 Service
The administrator can manage all the access methods on NeoGate TA on the "Service"
page.
Figure III-3-4 Service Settings
Table III-3-2 Description of Service Settings
Items
Description
SSH
By using SSH, you can log in to NeoGate and run commands. It's
disabled by default. We don't recommend enabling it if not needed.
The default port for SSH is 8022;
FTP FTP access;
The default port is 21.
TFTP
TFTP access;
The default port is 23.
HTTP HTTP web access;
The default port is 80.
HTTPS HTTPS web access, it is disabled by default, and you can enable it
to get safer web access.
3.1.3 VLAN Settings
A VLAN (Virtual LAN) is a logical local area network (or LAN) that extends beyond a single
traditional LAN to a group of LAN segments, given specific configurations.

NeoGate TA410/810 User Manual
15/51
Note:
NeoGate TA is not the VLAN server, a 3-layer switch is still needed, please configure the
VLAN information there first, then input the details in NeoGate TA, so that the packages
via NeoGate TA will be added the VLAN label before sending to that switch.
Figure III-3-5 VLAN Settings
Table III-3-3 Description of VLAN Settings
Items
Description
NO.1
Click the NO.1 you can edit the first VLAN over LAN
VLAN Number The VLAN Number is a unique value you assign to each VLAN
on a single device
VLAN IP Address
Set the IP Address for NeoGate TA VLAN over LAN.
VLAN Subnet Mask
Set the Subnet Mask for NeoGate TA VLAN over LAN.
Default Gateway
Set the Default Gateway for NeoGate TA VLAN over LAN
NO.2 Click the NO.2 you can edit the first VLAN over LAN.
VLAN Number The VLAN Number is a unique value you assign to each VLAN
on a single device.
VLAN IP Address
Set the IP Address for NeoGate TA VLAN over LAN.
VLAN Subnet Mask Set the Subnet Mask for NeoGate TA VLAN over LAN.
Default Gateway Set the Default Gateway for NeoGate TA VLAN over LAN.
3.1.4 VPN Settings
A virtual private network (VPN) is a method of computer networkingtypically using the
public internetthat allows users to privately share information between remote locations,
or between a remote location and a business' home network. A VPN can provide secure
information transport by authenticating users, and encrypting data to prevent
unauthorized persons from reading the information transmitted. The VPN can be used to
send any kind of network traffic securely. NeoGate TA supports OpenVPN.

NeoGate TA410/810 User Manual
16/51
Figure III-3-6 VPN Settings
·Enable VPN
·Import VPN Config
Import configuration file of OpenVPN.
Notes:
1. Uncomment “user” and “group” in the “config” file. You can get the config package from
the OpenVPN provider.
2. NeoGate TA works as VPN client mode only.
3.1.5 DDNS Settings
DDNS (Dynamic DNS) is a method/protocol/network service that provides the capability
for a networked device, such as a router or computer system using the Internet Protocol
Suite, to notify a Domain Name System (DNS) name server to change, in real time, the
active DNS configuration of its configured hostnames, addresses or other information.
Figure III-3-7 DDNS Settings
Table III-3-4 Description of DDNS Settings
Items
Description
DDNS Server Select the DDNS server you sign up for service.
User Name User name the DDNS server provides you.
Password User account’s password.
Host Name The host name you have got from the DDNS server
Note: DDNS allows you to access your network using domain names instead of IP
address. The service manages changing IP address and updates your domain information

NeoGate TA410/810 User Manual
17/51
dynamically. You must sign up for service through dyndns.org, freedns.afraid.org,
www.no-ip.com, www.zoneedit.com.
3.1.6 Static Route
NeoGate TA will have more than one Internet connection in some situations but it has only
one default gateway. You will need to set some Static Route for NeoGate TA to force it to
go out through different gateway when accessing to different internet.
The default gateway priority of NeoGate TA from high to low is VPN/VLANLAN port.
Figure III-3-8 Static Route
1) Route Table
The current route rules of NeoGate TA.
2) Static Route Rules
You can add new static route rules here.
Table III-3-5 Description of Static Route Settings
Items
Description
Destination
The destination network to be accessed to by NeoGate TA.
Subnet Mask
Specify the destination network portion.
Gateway
Define which gateway NeoGate TA will go through when accessing
the destination network.
Metric
The cost of a route is calculated by using what are called routing
metric. Routing metrics are assigned to routes by routing protocols
to provide measurable statistic which can be used to judge how
useful (how low cost) a route is.
Interface
Define which internet port to go through.

NeoGate TA410/810 User Manual
18/51
3.2 Security Center
3.2.1 Security Center
You can check NeoGate TAsecurity configuration in “Security Center” page. And also, you
can enter the relevant security settings page rapidly.

NeoGate TA410/810 User Manual
19/51
Firewall:
Figure III-3-10 Firewall
In the “Firewall” tab, you can check firewall configuration and alert settings. You can enter
the configuration page directly by clicking the relevant button.
Service:
Figure III-3-11 Service
In “Service” tab, you can check AMI/SSH/FTP/TFTP/HTTP/HTTPS status. You can enter
the configuration page directly by clicking the relevant button.
Port:
Figure III-3-12 Port
In “Port” tab, you can check SIP port, HTTP port and HTTPS port. You can also enter the
relevant page by clicking the button in “Setting” column.
We recommend changing the default port for security.

NeoGate TA410/810 User Manual
20/51
3.2.2 Alert settings
If the device is under attack, the system will alert users via call or E-mail.
The attack modes include IP attack and Web Login.
Figure III-3-13 Alert Settings
1. IPATTACK
When the system is attacked by IP address, the firewall will add the IP to auto IP Blacklist
and notify the user if it matches the protection rule.
1) Phone Notification Settings
Table III-3-6 Description ofPhone Notification Settings
Items
Description
PHONE Notification
Whether to enable phone notification or not.
Number
The numbers could be set for alert notification; users can setup
multiple extension and outbound phone numbers. Please
separate them by “;”.
Example: “500;9911”, if the extension has configured Follow Me
Settings, the call would go to the forwarded number directly.
Attempts The attempts to dial a phone number when there is no answer.
Interval The interval between each attempt to dial the phone number.
Must be longerthan 3 seconds, the default value is 60 seconds.
Prompt
Users will hear the prompt while receiving the phone notification.
2) E-mail Notification Settings
Note: Please ensure that all voicemail settings are properly configured on the System
Settings -> Voicemail Settings page before using this feature.
Table III-3-7 Description ofE-mail Notification Settings
Items
Description
E-mail Notification Whether to enable E-mail Notification or not.
Recipient’s Name The recipients for the alert notification, and multiple email addresses are allowed, please separate them by “;”.
E.g. [e-mail];[e-mail];[email protected]
Subject The subject of the alert email.
Email Content Text content supports predefined variables. Variable names and corresponding instructions are as follows: