Yeastar Technology NeoGate TA410 User manual

TA410/810
User Manual
Version 41.19.0.15
Yeastar Information Technology Co. Ltd

TA410/810 User Manual
Contents
Contents..................................................................................................................2
Introduction.............................................................................................................4
Application Description..........................................................................................5
Configuration Guide...............................................................................................9
1. Login....................................................................................................................9
2. Status ................................................................................................................11
2.1 System Status............................................................................................... 11
2.1.1 Port Status.............................................................................................. 11
2.1.2 Network status........................................................................................12
2.1.3 System Info ............................................................................................12
2.2 Reports.........................................................................................................12
2.2.1 Call Logs................................................................................................13
2.2.2 System Logs...........................................................................................13
2.2.3 Packet Monitor Tool................................................................................14
3. System...............................................................................................................15
3.1 Network Preferences.....................................................................................15
3.1.1 LAN Settings...........................................................................................15
3.1.2 Service ...................................................................................................16
3.1.3 VLAN Settings........................................................................................16
3.1.4 VPN Settings..........................................................................................17
3.1.5 DDNS Settings.......................................................................................18
3.1.6 Static Route............................................................................................19
3.2 Security Center.............................................................................................20
3.2.1 Security Center.......................................................................................20
3.2.2 Alert settings...........................................................................................21
3.2.3 AMI Settings...........................................................................................24
3.2.4 Certificates .............................................................................................25
3.2.5 Firewall Rules.........................................................................................26
3.2.6 IP Blacklist..............................................................................................27
3.3 System Preferences......................................................................................28
3.3.1 Password settings ..................................................................................28
3.3.2 Date and Time........................................................................................29
3.3.3 Email Settings.........................................................................................29
3.3.5 Auto Provision Settings...........................................................................30
3.3.6 Firmware Update....................................................................................32
3.3.7 Backup and Restore...............................................................................33
3.3.8 Reset and Reboot...................................................................................33
4. Gateway.............................................................................................................34
2/55

TA410/810 User Manual
4.1 FXO Port List................................................................................................34
4.1.1 FXO Port List..........................................................................................34
4.1.2 Port Group..............................................................................................37
4.2 VoIP Settings................................................................................................38
4.2.1 VoIP Trunk..............................................................................................38
4.2.2 Trunk Group............................................................................................40
4.2.3 SIP Settings............................................................................................41
4.2.4 IAX Settings............................................................................................46
4.3 Routes Settings.............................................................................................47
4.3.1 IP->Port..................................................................................................47
4.3.2 IP->Port .............................................................................................49
4.3.3 Blacklist..................................................................................................51
4.3.3 Callback Settings...............................................................................51
4.4 Gateway Settings..........................................................................................52
4.4.1 General Preferences...............................................................................52
4.5Audio Settings...............................................................................................53
4.5.1 Custom Prompts.....................................................................................53
4.6Advanced Settings........................................................................................54
4.6.1 Tone Zone Settings.................................................................................54
4.5.1 DTMF Settings........................................................................................55
3/55

TA410/810 User Manual
Introduction
YeastarTA410/810 Analog VoIP Gateways are cutting-edge products that connect
legacy telephones, fax machines and PBX systems with IP telephony networks and
IP-based PBX systems. Featuring rich functionalities and easy configuration,
TA410/810 is ideal for small and medium enterprises that wish to integrate a
traditional phone system into IP-based system. TA410/810 helps them to preserve
previous investment on legacy telephone system and reduce communication costs
significantly with the true benefits of VoIP.
Features
● 4/8 FXO ports
● Fully compliant with SIP and IAX2
● Flexible calling rules
● Configurable VoIP Server templates
● Codec: G.711 a/u-law, G.722, G.723,G.726, G.729A/B, GSM,ADPCM
● Echo Cancellation: ITU-T G.168 LEC
● Web-based GUI for easy configuration and management
● Excellent interoperability with a wide range of IP equipment
For more information, please click:
http://www.yeastar.com/Products/Products.asp#NeoGateTA
Yeastar TA410/810 FXO Gateway features 4, 8 FXO interfaces for connection of
PSTN and PBX extension and one 10/100 Mbps LAN port.
For more information about the Yeastar TA hardware specification and how to install
the Yeastar TA, please refer to the document below:
http://www.yeastar.com/download/PartI_NeoGate_TA_Series_Installation_Guide_en.
pdf
4/55

TA410/810 User Manual
Application Description
Connect IPPBX and TA FXO Gateway
YeastarTA FXO gateway is a solution to extend FXO ports for your IPPBX.
Two modes are available for you to connect IPPBX and TA FXO gateway, we call
them VoIP mode and SPS (Service Provider SIP)/SPX (Service Provider IAX) mode.
Three modes are available for you to connect your SIP server and TA410/810
gateway. We call them SIP Account Mode, VoIP Mode and SPS (Service Provider SIP)
Mode. You can choose any one of the 3 modes to connect your SIP server and
TA410/810. SPS Mode is recommended.
Account Mode:
Create one SIP account on TA410/810, and take the SIP account to register one SIP
trunk on your SIP server. Then TA410/810 and your SIP server are connected by the
account.
Calls from SIP to PSTN
1) Create one outbound route on your SIP sever, and select the SIP trunk you
have registered just now.
2) Configure a “IP->Port” route on TA410/10, choose the SIP account in the field
“Call Source”, and choose a PSTN trunk or PSTN trunk group in the field “Call
Destination”.
3) Make a call from your SIP Server and the call should match the outbound
route dial rules.
Calls from PSTN to SIP
1) Create an inbound route on your SIP server, and select the SIP trunk you
have registered just now.
2) Configure a “Port->IP” route on TA410/810, choose a PSTN trunk or PSTN
trunk group in the field “Call Source”, and choose the SIP account in the filed
“Call Destination”.
3) When a call comes to PSTN trunk on TA410/810, the call will be routed to the
destination of the SIP server inbound route.
Register SIP account on IP phone
With account mode, you can directly take the SIP account to register on your SIP
phone or softphone; then make calls from softphone though PSTN trunk on
TA410/810 and receive incoming calls on your SIP phone or softphone. In this
way, you don’t have to set up any SIP server.
VoIP Mode
Take a SIP account from yourSIP server, and register it on TA410/810 as a VoIP trunk.
In this way, TA410/80 and your SIP server are connected.
Calls from SIP to PSTN
5/55

TA410/810 User Manual
1) Configure a IP-> Port route on TA410/810; choose the VoIP trunk in the field
“Call Source”, and choose PSTN trunk in the field “Call Destination”.Enable
Two-stage Dialing on the route.
2) Make a call from your SIP server, dial the SIP account number which is
registered on TA410/810. You will hear a dial tone, then dial the external
number out through PSTN trunk.
Calls from PSTN to SIP
1) Configure a Port->IP route on TA410/TA810, choose PSTN trunk in the field
“Call Source”, and choose the SIP trunk in the filed “Call Destination”.
2) When an incoming call reaches PSTN trunk on TA410/810, you will hear a
dial tone, then dial an extension number of the SIP server.
SPS Mode(Recommended)
Create a Service Provider SIP trunk on TA410/810 to connect to your SIP server. Add
another Service Provider SIP trunk on your SIP server, connecting to TA410/810.
Calls from SIP to PSTN
1) Create one outbound route on your SIP sever, and select the SIP trunk you
have created just now.
2) Configure a IP->Port route on TA410/810, choose the SPS trunk in the field
“Call Source”, and choose PSTN trunk in the field “Call Destination”.
3) Make a call from your SIP Server and the call should match the outbound
route dial rules.
Calls from PSTN to SIP
1) Configure a Port->IP route on TA410/810, choose PSTN trunk in the field
“Call Source”, and choose the SPS trunk in the filed “Call Destinatiom”.
2) Create one inbound route on your SIP server and select the SIP trunk created
just now.
3) When an incoming call reaches PSTN trunk on TA41/810, You will hear a
dial tone, then dial an extension number of the SIP Server, it will be routed to
the destination of the SIP server inbound route.
Note:if you want the call to go directly to the destination number of your SIP
server, you don’t have to create an inbound route on SIP server, instead set a
Hotline number on TA410/810 route.
6/55

TA410/810 User Manual
For incoming calls from the PSTN to TA410/810, TA410/810 will forward the call to a
configured SIP extension or to an inbound destination of IPPBX like IVR.
7/55

TA410/810 User Manual
Connect TA FXO Gateway and FXS Gateway
TAFXO gateway can be connected to a FXS gateway using SPS/SPX Mode. Imagine
this, the FXO gateway is set up in Site A, and the FXS gateway in Site B. People in
Site B can make and receive calls using the local PSTN lines (which is connnected to
Site A’s provoider). With this solution, you can call a local number using a local PSTN
line wherever you are.
8/55

TA410/810 User Manual
Configuration Guide
1. Login
The TA gateway attempts to contact a DHCP server in your network to obtain valid
network settings (e.g., the IP address, subnet mask, default gateway address and
DNS address) by default.
Please enable DHCP Server in your network to obtain the TA40/810 IP address.
How to check TA410/810 IP address:
1. Download a DeviceFound tool from Yeastar website: FindTA.rar
2. Run the DeviceFound.exe software.
3. The detected TA devices in the local network will appear in the window.
4. Find the TA device’s IP address by the device’s MAC address or the SN.
Figure1-1 Device Found Software
Logging On:
After entering the IP address in the Web browser, users will see a log-in screen.
Check the default settings below:
Username: admin
Password: password
9/55

TA410/810 User Manual
In this example, the IP address is 192.168.10.125, the model is TA810.
Figure1-2 TA Login page
Click "Login" to get the welcome page.
Figure1-3 Login TA
10/55

TA410/810 User Manual
2. Status
Click to check the status of TA, including the system status and the detailed
reports.
2.1 System Status
In this page, we can check the status of the system, including trunk status, network
status and system information.
2.1.1 Port Status
Figure 2-1FXO Port Status
Up/Down:
Up/Down
Description
Up
The FXO interface works well.
Down
The FXO interface is broken.
VoIP Status:
Status
Description
OK Successful registration, trunk is ready for use
Unreachable
The trunk is unreachable.
Request Send
Registering.
Waiting for authentication
Wrong password or user name.
Failed
Trunk registration failed.
FXO Status
Hook
Description
Idle
The FXO port is idle.
Busy
The FXO port is busy.
11/55

TA410/810 User Manual
Disconnect
There is no line connected to the FXO port.
2.1.2 Network status
In this page, the IP address of LAN port will appear with their status.
Figure 2-2 Network Status
If your VLAN or VPN are configured, you can check the status in this page also.
2.1.3 System Info
In this page, we can check the hardware/firmware version, or the disk usage of TA.
Figure 2-3 System Info
2.2 Reports
In this page, we can check the call detailed log, system log, and use the packet tool to
debug the system when needed.
12/55

TA410/810 User Manual
2.2.1 Call Logs
The call log captures all call details, including call time, caller number, callee number,
call type, call duration,etc.An administrator can search and filter call data by call date,
caller/callee, trunk, duration, billing duration, status, or communication type.
Figure 2-4 Call Logs
2.2.2 System Logs
You can download and delete the system logs of TA.
Figure 2-5 System Logs
Options
·Enable Hardware Log
Save the information of hardware; (up to 4 log files)
·Enable Normal Log
Save the prompt information; (up to 16 log files)
13/55

TA410/810 User Manual
·Enable Web Log
Save the history of web operations (up to 2 log files)
·Enable Debug Log
Save debug information (up to 2 log files)
2.2.3 Packet Monitor Tool
This feature is used to capture packets for technician. Integrate packet capture tool
“Wireshark” is integrated in TA410/810.
Users also could specify the destination IP address and port to get the packets.
Figure 2-6 Packet Tool
·IP
Specify the destination IP address to get the packets.
·Port
Specify the destination Port to get the packets.
14/55

TA410/810 User Manual
3. System
Click to access. In this page, we can configure the network settings, security
settings and some system preferences.
3.1 Network Preferences
3.1.1 LAN Settings
Figure 3-1 Static IP Address Mode
Table 3-1 Description of LAN Settings
Items
Description
Hostname
Set the host name for TA
Static IP Address
Set the TA’s IP address as a static IP
IP Address Set the IP Address for TA.It
is recommended that you configure a
static IP address for TA.
Subnet Mask
Set the subnet mask for TA
Gateway
Set the gateway for TA
Primary DNS
Set the primary DNS for TA.
Secondary DNS
Set the secondary DNS for TA
IP Address2
Set the second IP Address for TA
Subnet Mask2
Set the second subnet mask for TA
Figure 3-2 DHCP Mode
Select DHCP mode to get network automatically from the local network.
15/55

TA410/810 User Manual
Figure 3-3 PPPoE
Fill in user name and password to access the Internet via PPPoE.
3.1.2 Service
The administrator can manage all the access methods on TAon the "Service" page.
Figure 3-4 Service Settings
Table 3-2 Description of Service Settings
Items
Description
SSH
By using SSH, you can log in to TA410/810 and run commands.
It's disabled by default. We don't recommend enabling it if not
needed.
The default port for SSH is 8022;
FTP
FTP access;
The default port is 21.
TFTP
TFTP access;
The default port is 23.
HTTP HTTP web access;
The default port is 80.
HTTPS
HTTPS web access, it is disabled by default, and you can enable
it to get safer web access.
3.1.3 VLAN Settings
A VLAN (Virtual LAN) is a logical local area network (or LAN) that extends beyond a
single traditional LAN to a group of LAN segments, given specific configurations.
16/55

TA410/810 User Manual
Note:
TA gateway is not the VLAN server, a 3-layer switch is still needed, please configure
the VLAN information there first, then input the details in TA gateway, so that the
packages via TA gateway will be added the VLAN label before sending to that switch.
Figure 3-5 VLAN Settings
Table 3-3 Description of VLAN Settings
Items
Description
NO.1
Click the NO.1 you can edit the first VLAN over LAN
VLAN Number
The VLAN Number is a unique value you assign to each
VLAN on a single device
VLAN IP Address
Set the IP Address for TA gateway VLAN over LAN.
VLAN Subnet Mask
Set the Subnet Mask for TA gateway VLAN over LAN.
Default Gateway
Set the Default Gateway for TA gateway VLAN over LAN
NO.2
Click the NO.2 you can edit the first VLAN over LAN.
VLAN Number The VLAN Number is a unique value you assign to each
VLAN on a single device.
VLAN IP Address
Set the IP Address for TA410/810 VLAN over LAN.
VLAN Subnet Mask
Set the Subnet Mask for TA410/810 VLAN over LAN.
Default Gateway
Set the Default Gateway for TA410/810 VLAN over LAN.
3.1.4 VPN Settings
Avirtual private network (VPN) is a method of computer networking typically using the
public internet that allows users to privately share information between remote
locations, or between a remote location and a business' home network. A VPN can
provide secure information transport by authenticating users, and encrypting data to
prevent unauthorized persons from reading the information transmitted. The VPN can
be used to send any kind of network traffic securely. TA410/810 supports OpenVPN.
17/55

TA410/810 User Manual
Figure 3-6 VPN Settings
·Enable VPN
·Import VPN Config
Import configuration file of OpenVPN.
Notes:
1. Uncomment “user” and “group” in the “config” file. You can get the config package
from the OpenVPN provider.
2. TA410/810 works as VPN client mode only.
3.1.5 DDNS Settings
DDNS (Dynamic DNS) is a method/protocol/network service that provides the
capability for a networked device, such as a router or computer system using the
Internet Protocol Suite, to notify a Domain Name System (DNS) name server to
change, in real time, the active DNS configuration of its configured hostnames,
addresses or other information.
Figure 3-7 DDNS Settings
Table 3-4 Description of DDNS Settings
Items
Description
DDNS Server
Select the DDNS server you sign up for service.
User Name
User name the DDNS server provides you.
Password
User account’s password.
Host Name
The host name you have got from the DDNS server
Note: DDNS allows you to access your network using domain names instead of IP
18/55

TA410/810 User Manual
address. The service manages changing IP address and updates your domain
information dynamically. You must sign up for service through dyndns.org,
freedns.afraid.org, www.no-ip.com, www.zoneedit.com.
3.1.6 Static Route
TA410/810 will have more than one Internet connection in some situations but it has
only one default gateway. You will need to set some Static Route for TA410/810 to
force it to go out through different gateway when accessing to different internet.
The default gateway priority of TA410/810 from high to low is VPN/VLANLAN port.
Figure 3-8 Static Route
1) Route Table
The current route rules of TA410/810.
2) Static Route Rules
You can add new static route rules here.
Table 3-5 Description of Static Route Settings
Items
Description
Destination
The destination network to be accessed to by TA410/810.
Subnet Mask
Specify the destination network portion.
Gateway
Define which gateway TA410/810 will go through when
accessing the destination network.
Metric
The cost of a route is calculated by using what are called routing
metric. Routing metrics are assi
gned to routes by routing
protocols to provide measurable statistic which can be used to
judge how useful (how low cost) a route is.
19/55

TA410/810 User Manual
Interface
Define which internet port to go through.
3.2 Security Center
3.2.1 Security Center
You can check TA410/810TA security configuration in “Security Center” page. And
also, you can enter the relevant security settings page rapidly.
Firewall:
Figure 3-10 Firewall
In the “Firewall” tab, you can check firewall configuration and alert settings. You can
enter the configuration page directly by clicking the relevant button.
Service:
Figure 3-11 Service
In “Service” tab, you can check AMI/SSH/FTP/TFTP/HTTP/HTTPS status. You can
enter the configuration page directly by clicking the relevant button.
20/55