Yeastar Technology Yeastar TE200 User manual

TE200 VoIP Gateway
User Manual
Version 61.0.0.7
Yeastar Information Technology Co. Ltd

TE200 User Manual
2/57
Copyright
Copyright 2006-2022 Yeastar Information Technology Co., Ltd. All rights
reserved.
No parts of this publication may be reproduced or transmitted in any form or by
any means, electronic or mechanical, photocopying, recording, or otherwise, for
any purpose, without the express written permission of Yeastar Information
Technology Co., Ltd. Under the law, reproducing includes translating into
another language or format.
Declaration of Conformity
Hereby, Yeastar Information Technology Co., Ltd.
declares that Yeastar TE200 gateway is in conformity
with the essential requirements and other relevant
provisions of the CE, FCC.
Warranty
The information in this document is subject to change without notice.
Yeastar Information Technology Co., Ltd. makes no warranty of any kind with
regard to this guide, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Yeastar Information
Technology Co., Ltd. shall not be liable for errors contained herein nor for
incidental or consequential damages in connection with the furnishing,
performance or use of this guide.
WEEE Warning
In accordance with the requirements of council directive 2002/96/EC
on Waste of Electrical and Electronic Equipment (WEEE), ensure that
at end-of-life you separate this product from other waste and scrap
and deliver to the WEEE collection system in your country for
recycling.

TE200 User Manual
3/57
Table of Contents
1. INTRODUCTION ................................................................................................................................5
1.1 Features ............................................................................................ 5
1.2 Hardware Specification ........................................................................ 6
1.2.1 Exterior Appearance .................................................................................................. 6
2. SYSTEM SETUP ................................................................................................................................. 8
2.1 Connection Drawing ............................................................................ 8
2.2 Connecting Ethernet Line ..................................................................... 8
2.3 Supplying Power ................................................................................. 8
3 ADMINISTRATOR LOGIN ................................................................................................................... 9
4. STATUS ........................................................................................................................................... 10
4.1 System Status .................................................................................. 10
4.1.1 IP Trunk status..........................................................................................................10
4.1.2 E1/T1 Status.............................................................................................................11
4.1.3 Network status .........................................................................................................12
4.1.4 System info...............................................................................................................12
4.2 Reports ............................................................................................13
4.2.1 Call logs.................................................................................................................... 13
4.2.2 System logs .............................................................................................................. 14
5. SYSTEM .......................................................................................................................................... 16
5.1 Network Preferences ..........................................................................16
5.1.1 LAN Settings ............................................................................................................. 16
5.1.2 WAN Settings........................................................................................................... 18
5.1.3 DDNS settings .......................................................................................................... 19
5.1.4 Static Route..............................................................................................................20
5.2 Firewall Settings ............................................................................... 21
5.2.1 Firewall Rules ........................................................................................................... 22

TE200 User Manual
4/57
5.2.2 IP Blocklist ................................................................................................................25
5.3 system Preferences ........................................................................... 26
5.3.1 Password Settings .................................................................................................... 26
5.3.2 Date and Time ..........................................................................................................27
5.3.3 Backup and Restore ................................................................................................. 28
5.3.4 Reset and Reboot .....................................................................................................29
5.3.5 Firmware Update..................................................................................................... 29
Upgrade through HTTP ..................................................................................................... 30
Upgrade through TFTP ...................................................................................................... 30
6. GATEWAY ....................................................................................................................................... 32
6.1 Digital Trunk .....................................................................................32
6.2 VoIP settings .................................................................................... 37
6.2.1 VoIP trunk ................................................................................................................ 37
6.2.2 SIP Settings ...............................................................................................................41
6.2.3 Trunk Group ............................................................................................................. 49
6.2.4 General Preferences.................................................................................................50
6.3 Routes Settings ................................................................................ 51
6.3.1 Route List ................................................................................................................. 51
6.3.2 Blocklist ....................................................................................................................55
6.4 Custom Prompts ......................................................................................................... 55
7. LOGOUT ......................................................................................................................................... 57

TE200 User Manual
5/57
1. Introduction
Yeastar TE200- Bridge the gap between E1/T1/J1 and VoIP networks
Yeastar TE200 offers SMBs cost effective additions to legacy telephone systems
to bring the true benefits of VoIP. TE200 is a dual-port VoIP E1/T1/J1 gateway
(VoIP to E1/T1/J1, and E1/T1/J1 to VoIP). Each E1 trunk supports up to 30
concurrent calls. It’s designed to bridge the gap between E1/T1/J1 and VoIP
networks. Integrating TE200 into an existing network will allow inexpensive
communication via SIP trunking. Also, it could connect VoIP systems with
E1/T1/J1 service from legacy carriers.
1.1 Features
●Trunk Support
●Call Routing Rules
●Automatic appending and stripping of digits to dialed numbers
●Caller ID name and number support
●FAX support
●Blocklist
●Firewall
●DDNS Support
●Backup and Restore
● Easy to install (web based)
● G729 codec support

TE200 User Manual
6/57
1.2 Hardware Specification
1.2.1 Exterior Appearance
Figure 1-1 Yeastar TE200 Front Panel
Table 1-1 Front Panel Descriptions
No.
Identifying
1Reset Button
Press and hold to reset to factory defaults.
2Power Indicator
Indicates the power status.
• On: The power is switched on.
• Off: The power is switched off.
③RUN Indicator
Indicates the system status.
• Blinking: The system is working properly.
• Not Blinking/Off: The system goes wrong.
④E1/T1
E1/T1 interface.
⑤Console
Console interface(RJ45) for debugging with connection
with a console cable.
⑥WAN
10/100/1000 Mbps adaptive RJ45 Ethernet port.
⑦LAN
10/100/1000 Mbps adaptive RJ45 Ethernet port.

TE200 User Manual
7/57
Figure 1-2 Yeastar TE200 Back Panel
Table 1-2 Back Panel Descriptions
No.
Identifying
①Power Switch
Press this button to switch on/off the device.
②Power Inlet
Connect the power supply to the port.
③Protective Earth
Protect the personnel and the equipment.

TE200 User Manual
8/57
2. System Setup
2.1 Connection Drawing
2.2 Connecting Ethernet Line
TE200 provides two 10/100/1000 Mbps Ethernet ports with RJ45 interface and
LED indicator. Plug Ethernet line into TE200’s Ethernet port, and then connect
the other end of the Ethernet line with a hub, switch, router, LAN or WAN. Once
connected, check the status of the LED indicator. A yellow LED indicates the port
is in the connection process, and a green LED indicates the port is properly
connected.
2.3 Supplying Power
Please follow the steps below to connect the TE200 unit to a power outlet:
1. Connect the small end of the power cable to the power input port on the
TE200 back panel, and plug the other end of the cable into a 100V~240V
AC power outlet.
2. Check the Power LED on the front panel. A solid green LED indicates that
power is being supplied correctly.

TE200 User Manual
9/57
3 Administrator Login
From your web browser, enter the IP address of the Yeastar TE200.
If this is the first time you are configuring TE200, please use the default settings
below (your PC should be in the same local network with TE200):
IP Address: http://192.168.5.150
Username: admin
Password: password
Figure 3-1 Web Configuration Panel Login Page
This is the welcome page of TE200 after login successfully.
Figure 3-2 Admin Configuration Interface

TE200 User Manual
10/57
4. Status
Click to check the status of TE200, including the system’s status and
the detailed reports.
4.1 System Status
In this page, we can check the status of the system, including IP trunk status,
E1/T1 status, network status and system information.
4.1.1 IP Trunk status
Figure 4-1 IP Trunk Staus
Table 4-1 Description of VoIP Trunk (SIP Type) Status
Status
Description
Unregistered
Trunk registration failed
Registered
Successful registration, trunk is ready for use
Request Sent
Registering
Waiting
Waiting for authentication
Table 4-2 Description of Service Provider SIP Trunk (SP-SIP Type) Status
Status
Description
OK
Successful registration, trunk is ready for use
Unreachable
The trunk is unreachable.

TE200 User Manual
11/57
Failed
Trunk registration failed.
4.1.2 E1/T1 Status
Figure 4-2 E1/T1 Status
Table 4-3 Description of E1 Trunk Status
Status
Description
Connected successfully; data stream on the trunk is normal;
but the trunk may not work if there is something wrong with
the E1 trunk communication protocol.
The port doesn’t have E1 line connected.
E1 line has been connected to the port; PRI is in
corresponding or can’t communicate.
Table 4-4 Status of Each Channel of E1 Trunk
Status
Description
Down
The Channel is not connected.
Idle
The channel is idle, ready for use.
Answered
The channel is busy in a call.
Accepted
The channel has accepted the call, but the phone
does not accept the call, i.e. the phone is ringing.
Dialing
The channel is dialing out.

TE200 User Manual
12/57
Offered
The channel is accepting an incoming call.
Disconnected
The channel is requesting to hang up, but the line
hasn't be released by the other end.
Blocked
At least one end is being blocked on the channel.
Unknown
The channel is being used in a non-call way, or status
unknown.
DChan
D channel, the control and signaling information is
being carried.
4.1.3 Network status
This page will display the IP addresses of the WAN and LAN ports and their
network status information.
Figure 4-3 Network Status
4.1.4 System info
On this page, you can check the hardware/firmware version, and the disk usage
of TE200.

TE200 User Manual
13/57
Figure 4-4 System Info
4.2 Reports
On this page, you can check the call logs and system logs, which can be used to
debug the problem you encountered.
4.2.1 Call logs
The call log captures all call details, including time, caller number, callee number,
call type, call duration, etc. An administrator can search and filter call data by
date, caller/callee, trunk, duration, billing duration, status, or communication
type.
Figure 4-5 Call Logs

TE200 User Manual
14/57
4.2.2 System logs
You can download and delete the system logs of TE200.
Figure 4-6 System Logs
Options
·Enable Hardware Log
Save the information of hardware; (up to 4 log files)
·Enable Normal Log
Save the prompt information; (up to 16 log files)
·Enable Web Log
Save the history of web operations (up to 2 log files)
·Enable Debug Log
Save debug information (up to 2 log files)

TE200 User Manual
15/57
Packet Capture Tool
This feature is used to capture packets. Users can specify the destination IP
address and port to get the packets.
·IP
Specify the destination IP address to get the packets.
·Port
Specify the destination Port to get the packets.

TE200 User Manual
16/57
5. System
Click to access the system page, where you can configure the network
settings, firewall rules and system preferences.
5.1 Network Preferences
5.1.1 LAN Settings
Figure 5-1 LAN Settings
·DHCP
If this option is set as yes, TE200 will act as DHCP client to get an available
IP address from your local network. Not recommended or you cannot access
TE200 without the right IP address.
·Enable SSH
This is the advance way to access the device, you can use the putty software
to access the device. In the SSH access, you can do more advance setting
and debug. It’s disabled by default.

TE200 User Manual
17/57
·Port
The default port is 8022.
·Hostname
Set the host name for TE200.
·IP Address
Set the IP Address for TE200.
It is recommended to configure a static IP address for TE200.
·Subnet Mask
Set the subnet mask for TE200.
·Gateway
Set the gateway for TE200.
·Primary DNS
Set the primary DNS for TE200.
·Secondary DNS
Set the secondary DNS for TE200.
·IP Address2
Set the second IP Address for TE200.
·Subnet Mask2
Set the second subnet mask for TE200.

TE200 User Manual
18/57
5.1.2 WAN Settings
Figure 5-2 WAN Settings
3 connection types are supported: DHCP (obtain an IP automatically), PPPoE,
and Static IP Address.
Note:
1. WAN port is disabled by default.
2. WAN port cannot be used as a router to route the internet packages from
WAN port to LAN port.
·DHCP
If your ISP says that you are connecting through DHCP or a dynamic IP address
from your ISP, perform these steps:
Step1: Select DHCP as the WAN Connection Type.
Step2: Click Save button to save the settings.
Step3: Reboot the device.
Step4: Check the WAN’s Status (StatusNetwork Status).

TE200 User Manual
19/57
·Static IP Address
If your ISP says that you are connecting through a static or fixed IP address
from your ISP, perform these steps:
Step1: Select Static IP Address as the WAN Connection Type.
Step2: Enter the IP Address.
Step3: Enter the Subnet Mask.
Step4: Enter the Gateway Address.
Step5: Enter the Primary DNS and Secondary DNS.
Step6: Click the Save button to save the settings.
Step7: Reboot the device.
Step8: Check the WAN’s Status (StatusNetwork Status).
·PPPoE
If your DSL provider says that you are connecting through PPPoE or if you
Normally enter a user name and password to access the Internet, perform these
Steps:
Step1: Select PPPoE as the WAN Connection Type.
Step2: Enter the User Name.
Step3: Enter the Password.
Step4: Click the Save button to save the settings.
Step5: Reboot the device.
Step6: Check the WAN’s Status (StatusNetwork Status)
5.1.3 DDNS settings
DDNS(Dynamic DNS) is a method / protocol / network service that provides the
capability for a networked device, such as a router or computer system using
the Internet Protocol Suite, to notify a Domain Name System (DNS) name
server to change, in real time, the active DNS configuration of its configured
host names, addresses or other information.

TE200 User Manual
20/57
Figure 5-3 DDNS Settings
5.1.4 Static Route
TE200 will have more than one internet connection in some situations but it has
only one default gateway. You will need to set some Static Route for TE200 to
force it to go out through different gateway when access to different internet.
The default gateway priority of TE200 from high to low is WAN portLAN port.
Figure 5-4 Static Route Settings
1) Route Table
The current route rules of TE200.
·Destination
The destination network to be accessed to by TE200.