yeedi Vac Hybrid User manual

yeedi vac hybrid
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUCCIONES
MANUEL D'INSTRUCTIONS
MANUALE D'USO
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ

7EN
Robot Instruction Manual
Edge Brush
Docking Station
Mopping Pad PlateWashable Mopping Pad
1. Package Contents/1.1 Package Contents
Note: Figures and illustrations are for reference only and may differ from actual product appearance.
Product design and specications are subject to changes without notice.
Instruction Manual

8
EN
1. Package Contents/1.2 Product Diagram
Anti-Collision Sensors and Bumper
AUTO Mode
Button
Multi-function
Cleaning Tool
Robot
Mapping Sensor
Bottom View
Power Switch
Wi-Fi Indicator
RESET Button
Anti-Drop Sensors
Carpet Detection
Sensor
Mopping Pad Plate
Slot
Water Outlet
Driving Wheels
Battery
Charging Contacts
Anti-Drop Sensors
Reservoir
Edge Brush
Universal Wheel
Main Brush
Main Brush
Release Button

9EN
Reservoir
Water Inlet
Mopping Pad Plate
Reservoir Release Button
Washable Mopping Pad
Docking Station
Docking Station Pins Power Cord
Dust Bin
High Efficiency Filter
Sponge Filter
Filter Net
Dust Bin Handle
Release Button

10
EN
2. Operating and Programming/2.1 Notes Before Cleaning
Tidy up the area to be cleaned by putting
furniture, such as chairs, in their proper place.
During the rst use, make sure each room door is
open to help Robot fully explore your house.
It may be necessary to place a physical
barrier at the edge of a drop to stop the
unit from falling over the edge.
Put away objects including wires,
cloths and slippers, etc. on the
oor to improve the cleaning
efciency.
Before using the product on a rug
with tasseled edges, please fold
the rug edges under.
Please do not stand in narrow
spaces, such as hallways, and
make sure not to block the
Detection Sensor.

11 EN
Please remove all protection materials on Robot and Docking Station before use.
1Assemble Docking Station 2Docking Station Placement
3Install Edge Brush 4Power ON
5Charge Robot Note: When Robot completes the cleaning cycle or when the battery
gets low, Robot automatically returns to the Docking Station to
recharge itself. Robot can also be sent back to the Docking Station at
any time by using the yeedi App or by pressing the AUTO Button on
the robot for 3 seconds.
Empty remaining water from the Reservoir and remove the Mopping
Pad Plate before charging Robot.
2. Operating and Programming/2.2 Preparation

12
EN
2. Operating and Programming/2.3 yeedi App
To enjoy all available features, it is recommended to control your Robot via the yeedi App.
Wi-Fi Indicator LightBefore you start, make sure that:
Tips:
If you have any problems during the Wi-Fi setup process, refer to the
Troubleshooting > Wi-Fi Connection section in this manual.
• Your mobile phone is connected to a Wi-Fi network.
• The 2.4GHz band wireless signal is enabled on your router.
• The Wi-Fi indicator light on Robot is slowly ashing.
Slowly flashing Disconnected to Wi-Fi or
waiting for Wi-Fi connection
Rapidly flashing Connecting to Wi-Fi
Solid Connected to Wi-Fi
yeedi

13 EN
2Pause
3Wake Up
Note: The robot’s Control Panel stops glowing after the robot is
paused for a few minutes. Press the AUTO Mode Button on Robot to
wake it up.
Press the AUTO button on Robot to wake it up
4Power OFF
Note: When Robot is not working, it is recommended to keep it
switched ON and charging.
2. Operating and Programming/2.4 Start, Pause, Wake Up, Power Off
1Start

14
EN
1
2
Note:
1. To prolong the service life of the reservoir, it is recommended to use puried water or softened water for the mopping system.
2. If you need to clean the carpet, please uninstall the Mopping Pad Plate rst.
3. Empty the reservoir after Robot nishes mopping.
Click
2. Operating and Programming/2.5 Mopping System

15 EN
Before performing cleaning and maintenance tasks on Robot, turn the robot OFF and unplug the Docking Station.
3. Maintenance/3.1 Mopping System
1 42
5
3
7 86

16
EN
Note: 1. Please rinse the lter with water as shown above. 2. Do not use nger or brush to clean the lter.
3. Be sure to dry out the lter for at least 24 hours after washing.
3. Maintenance/3.2 Dust Bin and Filters
Dust Bin
3 6
41
2 5
7
8

17 EN
Main Brush
Edge Brush Mapping Sensor
Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
1 2 3
3. Maintenance/3.3 Main Brush, Edge Brush and Mapping Sensor

18
EN
Note: Before cleaning the robot’s Charging Contacts and Docking Station Pins, turn the robot OFF and unplug the Docking Station.
3. Maintenance/3.4 Other Components

19 EN
To keep Robot running at peak performance, perform maintenance tasks and replace parts with the following frequencies:
A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: yeedi manufactures various replacement parts and ttings. Please contact Customer Service for more information on replacement parts.
Robot Part Maintenance Frequency Replacement Frequency
Washable Mopping Pad After each use Every 50 washings
Reservoir/Mopping Pad Plate After each use /
Edge Brush Once every 2 weeks Every 3-6 months
Main Brush Once per week Every 6-12 months
Sponge Filter/High Efciency Filter Once per week Every 3-6 months
Universal Wheel
Anti-Drop Sensors Bumper
Mapping Sensor
Charging Contacts
Docking Station Pins
Once per week /
3. Maintenance/3.5 Regular Maintenance

20
EN
4. Indicator Light
Robot will tell you something is wrong with an indicator light and voice report. More detailed support is available through the yeedi app
and online website.
Robot
Indicator Light Scenario
AUTO Mode Button glows a solid WHITE.
The robot is cleaning.
The robot is paused while cleaning.
AUTO Mode Button ashes WHITE.
The robot is charging.
The robot is starting.
The robot is relocating.
AUTO Mode Button glows a solid RED. The robot has low battery.
AUTO Mode Button ashes RED. The robot has a problem.

21 EN
No. Malfunction Possible Causes Solutions
1Robot is not able to connect to
the home Wi-Fi network.
Incorrect home Wi-Fi username or password
entered. Enter the correct home Wi-Fi username and password.
Robot is not within range of your home Wi-Fi
signal.
Make sure Robot is within range of your home Wi-Fi
signal.
Network setup started before Robot was
ready.
Turn ON Power Switch. Press the RESET Button for 3
seconds. Robot is ready for network setup when it plays
a musical tune and its Wi-Fi Indicator light ashes slowly.
2 Robot is not charging.
Robot is not switched ON. Switch ON Robot.
Robot has not connected to the Docking
Station.
Be sure that the robot’s Charging Contacts have
connected to the Docking Station Pins.
The Power Cord is not connected to the
Docking Station.
Make sure the Power Cord is rmly connected to the
Docking Station.
The battery is completely discharged.
Re-activate the battery. Switch ON. Place Robot on the
Docking Station by hand, remove after charging for 3
minutes, repeat 3 times; then charge normally.
Make sure the Docking Station is connected
to the power supply.
The Docking Station is not connected to the power
supply.
5. Troubleshooting/5.1 Troubleshooting

22
EN
No. Malfunction Possible Causes Solutions
3Robot cannot return to the
Docking Station.
The Docking Station is not correctly placed. Refer to section 2.2 to correctly place the Docking
Station.
The Docking Station is disconnected or
moved.
Please check if the Docking Station is connected to
power. Do not move the Docking Station manually.
Robot is working in a dark environment. Make sure to use Robot in a well illuminated environment.
Robot is paused for more than 60 minutes. Avoid pausing Robot for over 60 minutes.
Robot did not start cleaning from the Docking
Station.
Make sure Robot starts cleaning from the Docking
Station.
4
Robot returns to the Docking
Station before it has nished
cleaning.
Robot is working in a dark environment. Make sure to use Robot in a well illuminated environment.
When the battery gets low, Robot
automatically switches to Return to Charger
Mode and returns to the Docking Station to
recharge itself.
This is normal. No solution necessary.
Working time varies according to oor
surface, room complexity and the Cleaning
Mode selected.
This is normal. No solution necessary.
The cleaning area is not tidy. Remove small objects from the oor and tidy up the
cleaning area before Robot starts cleaning.
5Robot gets stuck while working
and stops.
Robot is tangled with something on the oor
(electrical wires, curtains, Carpet fringing, etc.).
Robot will try various ways to free itself. If it is
unsuccessful, manually remove the obstacles and restart.
6Robot makes much noise when
cleaning.
The brushes are tangled, or the dust bin is
stuck. Clear the debris stuck regularly.

23 EN
No. Malfunction Possible Causes Solutions
7
The water is not coming out of
the Reservoir when Robot is
mopping.
The water inlet lter on the bottom of
Reservoir is clogged.
Unscrew the water inlet on the bottom of Reservoir and
clean the lter.
The Reservoir runs out of water. Add water into the Reservoir.
The water outlets on the bottom of Robot are
clogged. Check the water outlets on the bottom and clean.
8The reservoir drops out of
place during cleaning. The reservoir is not properly installed. The reservoir is properly installed when it clicks into place.

24
EN
5. Troubleshooting/5.2 Wi-Fi Connection
Before Wi-Fi setup, make sure Robot, mobile phone, and Wi-Fi network meet the following requirements.
Robot and Mobile Phone Requirements
• Robot is fully charged and the power switch of Robot is turned on.
• Wi-Fi status light slowly ashes.
• Turn off mobile phone’s cellular data (you can turn it back on after setup).
Wi-Fi Network Requirements
• You are using a 2.4GHz or 2.4/5 GHz mixed network.
• Your router supports 802.11b/g/n and IPv4 protocol.
• Do not use a VPN (Virtual Private Network) or Proxy Server.
• Do not use a hidden network.
• WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.
• WEP EAP (Enterprise Authentication Protocol) is not supported.
• Use Wi-Fi channels 1-11 in North America and channels 1-13 outside North America (refer to local regulatory agency).
• If you are using a network extender/repeater, the network name (SSID) and password are the same as your primary network.

25 EN
6. Product Specifications
Model DVX34
Rated Input 20V 1A
Docking Station Model CH1822 CH1918*
Rated Input 100-240V 50-60Hz 0.5A Rated Input
(Charging)
For European
Union Only 220-240V 50-60Hz 0.3A
For Russia
Only 220V 50-60Hz 0.3A
Rated Output 20V 1A Rated Output 20V 1A
/ Power (Auto-Emptying) 1000W
Frequency bands 2400-2483.5MHz
Off Mode Power Less than 0.50W
Networked Standby Power Less than 2.00W
Output power of the Wi-Fi module is less than 100mW.
Note: Technical and design specications may be changed for continuous product improvement.
* CH1918 is an Self-empty Station sold separately that automatically empties your Robot's dustbin.
Explore more accessories at https://www.yeedi.com.