York ECO HFC-410A User manual

Packaged Rooftop
Air-Conditioning Units
(Simplicity Elite with HFC-410a refrigerant)
50 THROUGH 65 TONS
FORM 100.50-EG5 (108)
TM
MEA
231-02-E
ASHRAE
90.1
COMPLIANT
00873VIP

JOHNSON CONTROLS
2
FORM 100.50-EG5 (108)
Introduction
Better Economy...
Lower total cost of ownership
• High efficiency Eco2rooftop units are optimized for
HFC-410a refrigerant. YORK provides the FIRST
standard product offering that meets the latest
ASHRAE 90.1 energy efficiency requirements.
• Accurate ventilation control ensures that no more
than the proper amount of ventilation air is utilized.
This avoids the energy cost of conditioning excess
outside air and simultaneously monitors all other
unit functions for maximized energy efficiency.
• Flexible design configurations simplify the design
processandallowstheEco2tobeappliedtovirtually
any building application.
• Accessibilitythroughdouble-wallaccessdoors,spa-
ciouscompartmentsandsupportivefloorsimproves
serviceability.
• Note that modulating heat is not offered with Elite
controller option.
Simplicity Elite controller Option
Better Ecology...
Indoor air quality features for the indoor environ-
ment
• Double-wall construction of the roof, floor, doors,
and walls prevents insulation fibers from entering
the conditioned air. The inner liner also facilitates
periodiccleaningoftheunittopreventharmfulbuild-
up of bacteria or contaminants.
• The rooftop unit control center uses microprocessor
logic to analyze and optimize ventilation decisions and
performdemandventilation,andallowairflowcompen-
sation to maintain the air quality at a healthy level.
PROGRAM TEST/UP
2 CHARACTER DISPLAY
4 CHARACTER DISPLAY
ADDRESS/DOWN
ALARM/CHANGE LED
RS 485 PORT
RS 485 PORT
The Eco2packaged rooftop – designed to meet the demands of the
market for today and tomorrow.

FORM 100.50-EG5 (108)
3
JOHNSON CONTROLS
Introduction................................................................2
Features and Benefits ...............................................4
Application Data ........................................................8
Nomenclature..........................................................13
Physical Data...........................................................14
Altitude and Temperature Corrections.....................17
Cooling Performance Data......................................19
Supply Fan Data......................................................23
Component Static Pressure Drops..........................24
Exhaust Fan Data....................................................25
Electrical Data .........................................................26
Controls...................................................................28
General Arrangement Drawings..............................32
Unit Weights............................................................36
Guide Specifications................................................38
TABLES
1 Supply-Air-Duct Connection Configurations ......9
2 Return-Air-Duct Connection Configurations.......9
3 Physical Data...................................................14
4 Efficiency Ratings ............................................16
5 Physical Data – Unit EER................................16
6 Physical Data – Compressors..........................16
7 Altitude Correction Factors ..............................17
8 Cooling Performance Data – 050 Model..........19
9 Cooling Performance Data – 051 Model..........20
10 Cooling Performance Data – 060 Model..........21
11 Cooling Performance Data – 061 Model..........22
12 Supply Fan Performance – Forward-Curved...23
13 Supply Fan Performance –Airfoil ....................23
14 Component Static Pressure Drops..................24
15 Exhaust Fan Performance...............................25
16 Compressor Electrical Data.............................26
17 Power Supply Voltage Limits ...........................26
18 Supply and Exhaust Fan Motor
Electrical Data - ODP.......................................27
19 Supply and Exhaust Fan Motor
Electrical Data - TEFC.....................................27
20 Condenser Fan Motor RLA..............................27
21 Miscellaneous Electrical Data..........................27
22 Power-Supply-Conductor Size Range.............31
23 Unit Weights.....................................................36
24 Unit Center of Gravity......................................36
25 Unit Corner Weights.........................................37
FIGURES
1 Traditional Overhead VAV Air Delivery
System.............................................................10
2 Altitude/Temperature Conversion Factor .........18
3 Bottom Supply/Bottom Return Drawing...........32
4 Side Supply/Rear Return Drawing...................33
5 Bottom Supply/Side Return Drawing ...............34
6 Curb Layout Drawing.......................................35
Table of Contents

JOHNSON CONTROLS
4
FORM 100.50-EG5 (108)
Features and Benefits
AIRFLOW CONFIGURATIONS
Variable-Air-Volume – Eco2units are available for
single-zone variable-air-volume (VAV) applications.
Supply fans are controlled to the supply duct static
pressure setpoint, which can be reset via a BAS, or
through an analog voltage input on the unit controller
for optimized duct static pressure control. The static
pressure transducer is provided in the rooftop unit, and
5/16” or 1/4” plastic tubing and static pressure sensor
mustbe supplied byothers and installedapproximately
3/4 down the longest duct run.
Constant Volume – Eco2units are available for single-
zoneconstantvolumeapplications.Controlcanbeused
with a zone sensor, thermostat, or building automation
system.
COOLING AND HEATING CONFIGURATIONS
Cooling Only – For applications where no heat is
required, or heating is provided elsewhere within the
building HVAC system, cooling only units include an
empty discharge plenum. Supply duct connections are
configurable for bottom, left or right discharge. The
supply air temperature sensor is included and factory-
installed.
Staged Gas Heat –For applications requiringgas heat
for morning warm-up, or other heating needs, a staged
natural gas furnace is available. The furnace is located
inthe discharge plenum, downstreamof the supply fan.
Thesupplyair temperature sensor is locatedacrossthe
face of the supply duct opening in the unit. Furnaces
aredesigned in 375 mbh modules with onestage each.
Three are available on the YPAL050-061 with bottom
discharge and two are available on the YPAL050-061
withleft-side discharge. Ignitionand safety controlsare
included and factory-wired.
POWER OPTIONS
Single-point supply with terminal block – This
configuration is standard, and includes three terminals
for the incoming 3-phase power and is the standard
configuration for the Eco2product. It includes the en-
closure, terminal-block, and interconnecting wiring to
the compressors, heater and furnace controls, all fans,
etc. In this configuration, code requires that a means of
disconnect (not provided) must be installed at the site
within line-of-sight of the equipment.
Single-point supply with non-fused disconnect switch
– This option is the same the single-point with terminal
block option except it includes a unit-mounted through-
the-door manual non-fused disconnect switch with an
external, lockable handle (in compliance with Article
440-14 of N.E.C.). This option provides a means to
isolatethe unit power voltage for servicing. Othersmust
supplyseparate external fusing which mustcomply with
the National Electric Code and/or local codes.
Dual-pointsupplywithterminalblock–Thisoptionin-
cludesenclosure,terminal blocks circuited tothesupply
and exhaust fans and control transformer and a second
set of terminal blocks with interconnecting wiring to the
compressors, heat (if applicable) and condenser.
Convenience Outlet –Thisoptionsincludesapowered
115V GFCI convenience outlet that can be used for
powering tools or lights for servicing.Aprotective cover
plate is included while not in use. The outlet is located
on the bottom left hand corner of the power panel.
CONTROL FEATURES AND OPTIONS
Simplicity Elite Unit Controller – All Eco2units are
equipped with a factory-installed, programmed and
commissionedunitcontrollerwith all I/O capabilities and
control sequences. The controls include all on-board
diagnostic, safety and control features to operate the
rooftop unit. Two RS485 communication ports are in-
cluded as standard with one alarm output, a shutdown
contact, smoke ventilation contact, analog inputs for
supply air temperature and duct static pressure reset,
along with a variety of other capabilities.
Standard Ambient – YPAL050-061 models operate
down to 40°F as standard.
LowAmbient –Thisoptionincludeslowambientcontrol
of the first refrigerant circuit down to 0°F through the
use of suction and discharge pressure transducer on
circuit one, and condenser fan speed using a variable-
frequencydrive on thefirst condenser fanof circuit one.
Mechanical cooling with circuit two is locked out below
45°F (adjustable).
Flexsys bypass control option is not available with elite
controller.
SENSOR AND THERMOSTAT AND SENSOR
OPTIONS
Wall-Mount Zone Sensor – A thermistor zone sen-
sor for wall mounting. This zone sensor is for sensing
temperature only, and does not include any setpoint
adjustment features.
7-Wire Thermostat – This option is for a ship-loose
thermostat to interface with the Eco2unit. All models,
YPAL050-061, include an interface for a 7-wire ther-
mostat as standard.

FORM 100.50-EG5 (108)
5
JOHNSON CONTROLS
COMMUNICATIONS
BACnet MSTP (RS-485) Communications – This
communication is available via optional Modlinc Gate-
way. Communications to the unit are through a twisted
pair, and the wire terminations are on the primary unit
control board.
Modbus RTU Communications –Thiscommunication
is standard on every Eco2unit and can be used in lieu
of the BACnet communications (only one can be used
at a time).
FILTER OPTIONS
Filter Options – Two-inch 30% throwaway, cleanable,
carbon or pleated filters in an angled rack are avail-
able. For higher filtration requirements, optional rigid
filter racks are available with twelve-inch 65% or 95%
efficient rigid filters. Two-inch pre-filters are included
with rigid filter options. The rigid filter rack option is
availablewithout filter media where field-suppliedfilters
are required.
OUTSIDE AIR DAMPER OPTIONS
Manual Damper – This option includes a manually
adjustable outside air damper. It is manually adjust-
able at the unit by setting a mechanical stop between
0-100 percent.
Two-Position – This outside air damper option is con-
trolled to a two positions, opened and closed. Determi-
nationofthedamperpositionisbasedontheoccupancy
schedule.Inthe occupied mode, the outsideairdamper
is positioned to the manually configured point (set by
mechanicalstop). In the unoccupiedmode, the damper
is fully closed.
Modulating Economizer – This option includes
modulating outdoor air and return air dampers that are
interlocked and positioned by fully modulating, solid
state damper actuators. Control of the damper is via a
standardambientoutdoorairdrybulbsensor,oroptional
single or comparative enthalpy controls.
Rain Hoods on Outside Air Intakes – For all options
withoutsideairintakeopenings,rainhoodsareprovided
as standard to keep moisture from entering the equip-
ment. Rain hoods as an integral part of the unit and are
rotated into place.
RELIEF SYSTEM
Barometric Relief – Optional building air exhaust shall
be accomplished through barometric relief dampers in-
stalled in the return air plenum. The dampers will open
relative to the building pressure. The opening pressure
shall be adjustable via a spring tension adjustment.
Modulating Powered Exhaust with Damper Control–
This option consists of a constant-speed exhaust fan
withadischarge damper that is modulatedtocontrol the
flowofexhaustair.The damper control logic isbasedon
the building static pressure setpoint within the rooftop
unit controller. The static pressure transducer is pro-
vided in the return plenum of the rooftop unit, and 5/16”
or 1/4” plastic tubing and static pressure sensor must
be supplied by others and installed in a representative
location in the building.
Modulating Powered Exhaust with a VFD – This
option consists of a VFD to modulate the speed of the
exhaust fan to control the flow of exhaust air. The VFD
control logic is based on the building static pressure
setpoint within the rooftop unit controller. The static
pressure transducer is provided in the return plenum
of the rooftop unit, and 5/16” or 1/4” plastic tubing and
static pressure sensor must be supplied by others and
installed in a representative location in the building.
SUPPLY FAN OPTIONS
DWDI Forward-Curved Supply Fan – The standard
supplyairblowerisaforward-curvedsupplyfan.This fan
is good for medium static pressures and high airflows.
DWDI Airfoil Supply Fan – An optional airfoil blade
supply fan is available on all models for higher static
conditions.Thisoptionoffershigherefficiencyandlower
sound in certain applications.
Fan Skid Isolation – The entire supply fan assembly is
isolated from the unit base with one (standard) or two-
inch deflection springs with optional seismic restraints.
Supply and Exhaust Fan Motors – High efficiency
ODP, and standard and high efficiency TEFC motors
are available all meeting the Energy PolicyAct of 1992
(EPACT).
Supply Fan VFD and Manual Bypass – For VAV
applications, VFDs are provided to modulate air flow.
Optional manual bypass can also be provided to allow
full airflow in the event of a VFD failure.

JOHNSON CONTROLS
6
FORM 100.50-EG5 (108)
EVAPORATOR SECTION
Double Wall Construction – Double-wall construction
isthestandardconstructionoftheEco2andincorporates
powder coated pre-fabricated outer panels and corner
post for maximum exterior surface protection.
Factory Shrink-wrap – Eco2rooftop units are shipped
from the factory with factory-fresh shrink-wrap packag-
ing. No longer does the contractor need to worry about
dirt and debris clogging up condenser coils or moisture
leaking into the air handler on the units way to the job
site or rigging yard.
Copper Fins – For more extreme climates that aggres-
sivelycanattackaluminum,coppertubeevaporatorcoils
withcopperfinsareavailable.(Thisisnotrecommended
for units in areas where they may be exposed to acid
rain or environments where ammonia is present)
CONDENSER FEATURES AND OPTIONS
Scroll Compressors – Reliable, efficient, trouble-free
operation is the true measure of a packaged rooftop’s
value. That’s why YORK Eco2Packaged Rooftop
Air Conditioners use established scroll compressor
technology to deliver dependable, economical per-
formance in a wide range of applications. With the
Eco2Packaged Rooftop, you get the latest generation
of compressor enhancements added to the scroll’s
inherent strengths. The simplicity of a hermetic scroll
compressor allows the use of fewer moving parts to
minimize breakdown.
Multiple Compressor Staging –Throughthe use of the
scroll compressor, the Eco2has the ability to stage its
cooling by enabling and disabling multiple single stage
compressors on multiple circuits. These compressors
are manifolded together in pairs on a single refrigera-
tion circuit.
Compressor Circuiting – the Eco2is designed so that
only2scrollcompressorsareintandem within onerefrig-
eration circuit. This means more reliable compressors,
and less equipment down time. With multiple circuits, if
a compressor should ever fail on one circuit, the other
circuit will remain operational to work to maintain occu-
pied loads. The Eco2system has 2 circuits in a unit.
Condenser Fan Motors – The condenser fan motors
used on the Eco2unit are Totally Enclosed Air Over
(TEAO) to provide maximum durability through any
season.
Hot Gas Bypass – This options permits continuous,
stable operation at capacities below the minimum step
of unloading by introducing an artificial load on the
evaporator. For models YPAL050-061, it is used on the
lead circuit and standard on VAV units.
Replaceable Core Liquid Line Driers – Liquid line
driers are standard on the Eco2rooftop unit. An option
is provided for replaceable core driers.
Copper Fins – For more extreme climates that aggres-
sivelycanattackaluminum,coppertubecondensercoils
withcopperfinsareavailable.(Thisisnotrecommended
for units in areas where they may be exposed to acid
rain or environments where ammonia is present)
Pre-Coated Fins –An epoxy-coatedaluminumfinstock
to guard from corrosive agents and insulate against
galvanic potential. Recommended for mild seashore or
industrial locations.
Post-Coated Fins – Technicoat coil-coating process
used on condenser coils for seashore and other cor-
rosive applications (with the exception of strong alkalis,
oxidizers, wet bromide, chlorine and fluorine in concen-
trations greater than 100ppm).
Compressor Sound Blankets – Optional compressor
acoustic sound blankets are available for sound sensi-
tive applications.
ROOF CURBS
Partial perimeter roof curbs – This option includes a
knock-down 14” high roof curb for use with wood nailer
(by others). Roof curb supports the air handling section
with a separate support under the condenser end.
CABINET FEATURES AND OPTIONS
Double-Wall Access Doors - Full-sized access doors
provideeasyaccessintotheunit for routinemaintenance
and inspection. Solid wall liners encase insulation and
prevent damage and erosion into the airstream.
Industry-leading, 1,000-hour, salt-spray rating, per
ASTM B117, keeps unit in superior condition.
Features and Benefits (continued)

FORM 100.50-EG5 (108)
7
JOHNSON CONTROLS
ACCESSORIES
Filter Switch –An optional dirty filter alarm can be pro-
vided that will provide an alarm when the filters require
cleaning.
Magnahelic Filter Pressure Gauge – On units
equipped with downstream filtration, a magnahelic filter
gauge is included and visible on the exterior of the unit.
The filter gauge measures the air pressure drop for
through the rigid filter bank to indicate when replace-
ment is required.

JOHNSON CONTROLS
8
FORM 100.50-EG5 (108)
Application Data
GENERAL
TheEco2air conditioning units are designed for outdoor
installation. When selecting a site for installation, be
guided by the following conditions:
• Unit must be installed on a level surface.
• For the outdoor location of the unit, select a place
having a minimum sun exposure and an adequate
supply of fresh air for the condenser.
• Also avoid locations beneath windows or between
structures.
• Optional condenser coil protection should be used
for seashore locations or other harsh environ-
ments.
• Theunitshouldbeinstalledonaroofthat is structur-
ally strong enough to support the weight of the unit
withaminimumofdeflection.It is recommendedthat
the unit(s) be installed not more than 15 feet from
a main support beam to provide proper structural
support and to minimize the transmission of sound
and vibration. Ideally, the center of gravity should
be located over a structural support or building
column.
• Location of unit(s) should also be away from build-
ing flue stacks or exhaust ventilators to prevent
possible reintroduction of contaminated air through
the outside air intakes.
• Be sure the supporting structures will not obstruct
the duct, gas or wiring connections.
• Proper service clearance space of 6-feet around
the perimeter of the unit, 8-feet on one side for coil
servicing, and 12-feet to any adjacent units is re-
quired to eliminate cross contamination of exhaust
and outdoor air, and for maintenance tasks such
as coil pull and cleaning. No obstructions should
be above the condensing unit section.
LOCATION
Of the many factors that can effect the location of
equipment, some of the most important to consider are
Structural, Acoustical and Service clearances. Proper
attention should be made at the design stage to ensure
proper structural support. In cases where equipment is
being replaced, be aware of building design to insure
support is adequate for the application.
The next most important consideration in applying roof
top equipment is that of sound from the equipment.
Special care should be made to keep the roof top unit
away from sound sensitive areas such as conference
rooms,auditoriums and executive offices and any other
roomthatmayhavepotentialfortenantoccupancy.Pos-
sible locations could be above hallways, mechanical or
utility rooms.
Finally, service clearances should be maintained in
rooftop design to insure safe access to the unit. Unit
clearances are designed so that technicians have
enough space between units, building walls, and edges
of building to gain access safely. In cases where space
is limited, please call your local YORK representative
for additional information.
RIGGING
Properrigging and handling ofthe equipment is manda-
toryduringunloading and setting itinto position to retain
warranty status.
Spreader bars must be used by cranes to prevent dam-
ageto the unit casing.All lifting lugs must be used when
lifting the rooftop unit. Fork lifts will damage the rooftop
unit and are not recommended. Care must be taken to
keep the unit in the upright position during rigging and
to prevent damage to the watertight seams in the unit
casing. Avoid unnecessary jarring or rough handling.
UNIT PLACEMENT
• Elevated – Elevated roof curbs or dunnage steel
can be used to support the unit in order to raise it
to specific heights. When this type of placement
is required, be sure to keep unit access in mind.
Cat-walks or other forms of unit access may be
required to one or both sides of the unit, depend-
ing on your area of the country and the local codes
that are enforced. Please check with local officials
to ensure the application conforms to local codes
and regulations.
• Ground Level Locations – It is important that the
units be installed on a substantial base that will not
settle, causing strain on the refrigerant lines and
sheet metal and resulting in possible leaks. A one-
piece concrete slab with footers extended below
the frost line is highly recommended. Additionally,
the slab should be isolated from the main building
foundation to prevent noise and vibration trans-
mission to the building structure. For ground level
installations,precautions should be takento protect
theunitfromtamperingby,orinjury to, unauthorized
96"
LD08044
NOTE:
1. Under certain conditions these clearances may be encroached upon.
2. This is a visual reference for all Eco2units.

FORM 100.50-EG5 (108)
9
JOHNSON CONTROLS
persons.Erectingafencearoundthe unit iscommon
practice.
• Roof curb – YORK offers optional roof curbs
designed specifically for the Eco2footprint. This
curb comes as an open condenser model and is
shipped disassembled and requires field assem-
bly and installation. For bottom supply and return
openings, the curbs have matching connections to
ease installation. A pipe chase that matches the
rooftop unit pipe chase is also included in the curb
footprint for through-the-curb utility connections.
The curb should be located according to the loca-
tion recommendations above, and properly sealed
to prevent moisture and air leakage into and out of
the duct system. Flexible collars should be used
whenconnectingtheduct work to prevent unit noise
transmission and vibration into the building.
Duct work should be supported independently of the unit.
DUCT CONSIDERATIONS
Unlike competitive units where air can leave the rooftop
unit stratified across the width of the unit, the Eco2unit
sufficiently mixes airflow to ensure consistent air tem-
peraturefromtheunit.NospecialTee considerationsare
required and the unit may be oriented either way.
UNIT ORIENTATION
For applications with multiple rooftop units located in
close proximity on the roof, the orientation of the unit
may be important to reduce the potential for re-entrain-
mentofoutsideairflow.Regardlessoftheoutsideairand
exhaust air openings on a unit, all rooftop applications
can permit recirculation of exhaust air to the return, if
applied improperly.
HORIZONTAL APPLICATIONS
Thespectrum of applications for rooftop units in today’s
market is continuing to grow wider by the day. Flexibil-
ity in unit design and construction is a must in today’s
marketin order toinsure safe andsound applications of
HVACequipment.TheEco2hasbeen designed for spe-
cific application of horizontal supply and return airflow
taking the guess work out of unit application by building
a unit specific to these needs. If the application calls for
horizontal supply and return air, YORK can ship it from
the factory as a horizontal unit. This option elevates the
need for field modification of equipment, saving time
andmoney.TheEco2can support aleft discharge onall
units except 1,125 MBH gas, and/or right discharge on
allcooling-only units. Returnair can bebrought through
the end or side return air inlet making the unit specific
to building needs.
ECONOMIZER
The economizer section is used for ventilation of the
conditioned space to maintain indoor air quality, and
also to reduce energy consumption by using outdoor
air cooling in lieu of mechanical cooling. If outdoor air is
appropriate for cooling, but not sufficient for the cooling
demand,mechanicalcooling will stage onas necessary
until the cooling load is met.
Dual (comparative or differential) enthalpy operation is
the most accurate and efficient means of economizer
operation. The unit controller monitors the return and
outside air energy content, and selects the lower of the
two for operation.
LD08045
NOTE:
This diagram is provided as a visual reference of the Eco2discharge & return air openings & locations for all sizes. Please refer to the dimensional
data for exact size & location of panels and openings.
TABLE 1 – SUPPLY-AIR DUCT-CONNECTION CONFIGURATIONS
Unit Configuration SupplyAir
Bottom Left Right
50-65 Tons
Cooling only 
Cool/gas heat 375-750 MBH  N/A
Cool/gas heat 1,125 MBH N/A N/A
TABLE 2 – RETURN-AIR DUCT-CONNECTION CONFIGURATIONS
Unit Configuration ReturnAir
Bottom Left Rear
50-65 Tons
No exhaust 
Barometric relief damper 
N/A
Powered exhaust fan 
N/A

JOHNSON CONTROLS
10
FORM 100.50-EG5 (108)
Application Data (continued)
VAV SUPPLY AIR PRESSURE CONTROL
Traditional packaged rooftop systems use inlet guide
vanes (IGVs) for duct static pressure control. These
control supply duct pressure by modulating dampers
(introducinglossesand inefficiencies) on theinlet of the
fan,openandclosed.YORK’svariablefrequencydrives
(VFDs) offer superior fan speed control and quieter,
energy efficient operation.
For VAV applications, the YORK Eco2unit uses a VFD
to modulate fan speed and maintain a constant duct
static pressure. VFDs offer superior control over the
operationoftheunit at part load, andoffertheadditional
benefits of quieter and more efficient operation when
compared to IGV.
HARSH ENVIRONMENTS – CONDENSER AND
EVAPORATOR COIL PROTECTION
For harsh environmental conditions such as seashore
applications,YORKoffersthreetypesofcoilprotection:
copper fin material, black fin and Technicoat coatings.
YORKrecommendsthatforcorrosiveenvironmentsthat
copper fins be used to protect the evaporator and/or
condenser coils. In areas where chemicals that can
corrode copper are present, such as ammonia, YORK
recommendsthat the black fin orTechnicoat coating be
used for maximum protection.
• Copper-Fin Evaporator and Condenser Coil
– Copper fins can be used instead of aluminum for
additional corrosion protection. However, it is not
suitable for areas that are subject to acid rain or
exposed to ammonia.
• Pre-Coated Condenser Fins – Black fin coating
(yellow fin for evaporator fins) is pre-coated appli-
cation epoxy on aluminum fin stock to guard from
corrosive agents and insulate against galvanic
potential. It is used for mild seashore or industrial
locations. This can provide corrosion resistance
comparable to copper fin coils in typical seashore
locations.
• Post-Coated Condenser Fins – Technicoat (a
post-coated application of epoxy) can be used for
seashore and other corrosive applications with the
exception of strong alkaloides, oxidizers, wet bro-
mide,chlorineandfluorineinconcentrationsgreater
than 100 ppm. Any of the above suitable options
should be selected based on the particular project
design parameters and related environmental fac-
tors.Theapplicationshouldbefurtherreviewedand
approvedbytheconsultingengineerorowner based
on their knowledge of the job site conditions.
BUILDING PRESSURE CONTROL SYSTEMS
Building pressure control systems are often neces-
sary when economizers are used to bring in outdoor
air. Without proper building exhaust, the building may
become over pressurized. The pressure control system
maintains the proper building pressure by expelling the
appropriate amount of air from the building.
Exhaust/relief fans – In this application, a powered
exhaust fan may be suitable, however careful consid-
eration of the fan type is necessary. YORK offers a
centrifugalpoweredexhaustfantoperformthisfunction.
Somemanufacturersusea propeller exhaust fan, which
cannot handle the static pressure requirements.
Forsystemswithmoderate to low return static pressure,
an exhaust fan is recommended. The benefit of the ex-
haust fan is that it does not run all of the time, and may
facilitate compliance with the ASHRAE 90.1 fan motor
horsepower requirement.
The exhaust fan operates in parallel with the supply
fan. In this arrangement, the supply fan handles the full
static pressure requirements of the system. For normal
building pressure control, the exhaust fan operates to
draw air from the return plenum and exhaust it out of
the building.
The exhaust fan configuration is available in two forms,
modulatingandnon-modulating. Modulating is themost
common and recommended for the majority of applica-
tions, while non-modulating should be used with in only
certain circumstances.
Inthe modulating exhaust system,the volume ofairflow
exhausted from the building is proportional to the enter-
ing volume of outside air. Control is accomplished via
either a discharge damper or a variable-frequencydrive
(VFD). YORK recommends the use of a VFD to reduce
energy consumption, sound levels and improved reli-
ability due to fewer moving parts.
FIG. 1. TRADITIONAL OVERHEAD VAV AIR
DELIVERY SYSTEM

FORM 100.50-EG5 (108)
11
JOHNSON CONTROLS
In the non-modulating exhaust system, the exhaust air-
flow is constant whenever the exhaust fan is operating.
This type of control should only be used to either assist
a smoke purge system or when a system requires a
constant volume of exhaust airflow.
ACOUSTICAL CONSIDERATIONS
The Eco2unit is designed for lower sound levels than
competitive units by using flexible fan connections, fan
spring isolators, double-wall construction, multiple fan
options, and lower speed and horsepower fans. For
VAV applications, VFDs are used instead of inlet guide
vanes. Additional sound attenuation can be obtained
using compressor sound blankets and field-supplied
sound attenuators when necessary.
Even with these equipment design features, the acousti-
calcharacteristicsoftheentireinstallationmustneverbe
overlooked.Additional steps fortheacousticalcharacter-
isticsofarooftopinstallationshouldbeaddressedduring
the design phase of a project to avoid costly alterations
after the installation of the equipment. During the design
phase of a project, the designing engineer should con-
sider,ataminimum,theimpact oftheequipmentlocation,
rooftop installation, building structure, and duct work.

JOHNSON CONTROLS
12
FORM 100.50-EG5 (108)
This page intentionally left blank

FORM 100.50-EG5 (108)
13
JOHNSON CONTROLS
Nomenclature
1 2 34567 8 910 12 13 14 15 16
Base Type laicepSngiseDnruteRsgninepOylppuStnaregirfe
R
Opening
Y :YORK 0 5 0 :50 Ton Capacity B :R-407C :208/3/60X :Standard Product, IPU
P:Packaged Rooftop 0 5 1 :55 Ton Capacity C :R-22 :230/3/60 S :Special Product, IPU
A :Air Cooled 0 60:60 Ton Capacity E :R-410A 6:460/3/60 A :Standard Product, Simplicity Elit
e
L :Scroll 0 61:65 Ton Capacity 8 :575/3/60 B :Special Product, Simplicity Elite
C
V F
F
B:Bottom Return
C R:Rear Return
L:Left Return
nruteRediS:SnruteRmottoB:BN
ylppuStfeL:LXHS/SG
ylppuSthgiR-R
M
F :Full Modulating Gas Heat, S/S HX
E
H
S
:Electric Heat
:Hot Water Heat
:Steam Heat
Voltage
5
:Revision Level F (initial)
:Staged Natural Gas Heat
:Staged Natural Gas Heat,
:Full Modulating Gas Heat
:Constant Volume
:VAV, VFD
noitacilppAyticapaClan
i
moNt
cudo
rP
:Flexsys
:Cooling Only

JOHNSON CONTROLS
14
FORM 100.50-EG5 (108)
Physical Data
TABLE 3 – PHYSICAL DATA
MODEL 050 051 060 061
General Data
Length without hood (inches) 339 339 339 339
Width (inches) 92 92 92 92
Height (inches) 82 82 82 82
Compressor Data
Quantity 4 4 4 4
Type Scroll Scroll Scroll Scroll
Unit Capacity Steps 4 4 4 4
R410a Charge (SYS 1/2) (lb-oz) 50 / 50 50 / 50 58 - 11 / 58 - 11 58 - 11 / 58 - 11
Supply Fan
Quantity 1 1 1 1
Type FC FC FC FC
Size 28 - 28 28 - 28 28 - 28 28 - 28
Motor Size Range (HP) 10 - 40 10 - 40 10 - 40 10 - 40
Air Flow Range (CFM) 10,000 - 22,500 10,000 -22,500 12,500 - 24,000 12,500 - 24,000
Static Pressure Range (Total) 1.0" - 6.0" 1.0" - 6.0" 1.0" - 6.0" 1.0" - 6.0"
Optional Supply Fan
Quantity 1 1 1 1
Type AF AF AF AF
Size 28 28 28 28
Motor Size Range (HP) 10 - 40 10 - 40 10 - 40 10 - 40
Air Flow Range (CFM) 10,000 - 24,000 10,000 - 24,000 12,500 - 24,000 12,500 - 24,000
Static Pressure Range (Total) 1.0" - 8.0" 1.0" - 8.0" 1.0" - 8.0" 1.0" - 8.0"
Exhaust Fan
Quantity Fans/Motors 2 / 1 2 / 1 2 / 1 2 / 1
Type FC FC FC FC
Size 18 - 18 18 - 18 18 - 18 18 - 18
Motor Size Range (HP) 5 - 20 5 - 20 5 - 20 5 - 20
Air Flow Range (CFM) 4,000 - 22,500 4,000 - 22,500 4,000 - 24,000 4,000 - 24,000
Static Pressure Range (Total) 0.1" - 1.5" 0.1" - 1.5" 0.1" - 1.5" 0.1" - 1.5"
Evaporator Coil
Size (square feet) 52 52 52 52
Rows/FPI 3 / 17 3 / 17 4 / 17 4 / 17
Condenser Coil
Size (square feet) 88 88 88 88
Rows/FPI 2 / 17 2 / 17 3 / 17 3 / 17
Condenser Fans
Quantity 4 4 4 4
Type Prop. Prop. Prop. Prop.
Diameter (inches) 36 36 36 36
Motor HP 2 2 2 2
Filters - 2" throwaway (pre-filter position - angled)
Quantity 8 / 12 8 / 12 8 / 12 8 / 12
Size (length x width) (in.) 25x16 / 25x20 25x16 / 25x20 25x16 / 25x20 25x16 / 25x20
Total Filter Face Area (square feet) 61.6 61.6 61.6 61.6
Filters - 2" cleanable (pre-filter position - angled)
Quantity 8 / 12 8 / 12 8 / 12 8 / 12
Size (length x width) (in.) 25x16 / 25x20 25x16 / 25x20 25x16 / 25x20 25x16 / 25x20
Total Filter Face Area (square feet) 63.9 63.9 63.9 63.9
Filters - 2" pleated, 30% efficient (pre-filter position - angled)
Quantity 8 / 12 8 / 12 8 / 12 8 / 12
Size (length x width) (in.) 25x16 / 25x20 25x16 / 25x20 25x16 / 25x20 25x16 / 25x20
Total Filter Face Area (square feet) 63.9 63.9 63.9 63.9

FORM 100.50-EG5 (108)
15
JOHNSON CONTROLS
MODEL 050 051 060 061
Gas Furnaces
Staged Furnace Sizes (input/output/steps) 375 MBH / 300 MBH / 1 steps 750 MBH / 600 MBH / 2 steps
1125 MBH / 900 MBH / 3 steps
Gas Pressure Range 4.5" - 13.5"
IWC 4.5" - 13.5" IWC 4.5" - 13.5" IWC 4.5" - 13.5" IWC
Minimum OA Temp for Mech. Cig. 40°F 40°F 40°F 40°F
Low Ambient Option Min. OA Temp 0000
Minimum Airflow (Heating) 375 7,500 7,500 11,500 11,500
750 14,000 14,000 14,000 14,000
Bottom Supply Only 1,125 21,000 21,000 21,000 21,000
TABLE 3 – PHYSICAL DATA (cont’d)
MODEL 050 051 060 061
Filters - 12" rigid 65%, 2" 30% prefilter (pre-filter position)
Quantity 1 / 4 / 9 1 / 4 / 9 1 / 4 / 9 1 / 4 / 9
Size (length x width) (in.) 16x20/25x16/25x20 16x20/25x16/25x20 16x20/25x16/25x20 16x20/25x16/25x20
Total Filter Face Area (square feet) 43.0 43.0 43.0 43.0
Filters - 12" rigid 95%, 2" 30% prefilter (pre-filter position)
Quantity 1 / 4 / 9 1 / 4 / 9 1 / 4 / 9 1 / 4 / 9
Size (length x width) (in.) 16x20/25x16/25x20 16x20/25x16/25x20 16x20/25x16/25x20 16x20/25x16/25x20
Total Filter Face Area (square feet) 44.6 44.6 44.6 44.6
Filters - 2" carbon (pre-filter position - angled)
Quantity 8 / 12 8 / 12 8 / 12 8 / 12
16x20/25x16/25x20 25x16/25x20 25x16/25x20 25x16/25x20 25x16/25x20
Total Filter Face Area (square feet) 63.9 63.9 63.9 63.9
Filters - 12" rigid rack only, with 2" throwaways
Quantity 1 / 4 / 9 1 / 4 / 9 1 / 4 / 9 1 / 4 / 9
Size (length x width) (in.) 16x20/25x16/25x20 16x20/25x16/25x20 16x20/25x16/25x20 16x20/25x16/25x20
Total Filter Face Area (square feet) 43 43 43 43

JOHNSON CONTROLS
16
FORM 100.50-EG5 (108)
Physical Data
TABLE 6 – PHYSICAL DATA - COMPRESSORS
Compressors Utilized Compressor Nominal Tons % Capacity Per Stage
System 1 System 2 System 1 System 2
“Compr
# 1” “Compr # 2” “Compr # 3” “Compr # 4” “Compr # 1” “Compr # 2” “Compr # 3” “Compr # 4” “Stage 1” “Stage 2” “Stage 3” “Stage 4”
Model
050 ZP137 ZP120 ZP137 ZP120 13.58 12.53 13.58 12.53 26.0 52.0 76.0 100.0
051 ZP137 ZP137 ZP137 ZP137 13.58 13.58 13.58 13.58 25.0 50.0 75.0 100.0
060 ZP182 ZP137 ZP182 ZP137 17.95 13.30 17.95 13.30 28.7 57.4 78.7 100.0
061 ZP182 ZP137 ZP182 ZP154 17.95 13.30 17.60 14.86 28.2 55.8 76.7 100.0
TABLE 5 – PHYSICAL DATA – UNIT EER EER
Model Supply Blower
Type Cooling Only Gas Heat
YPAL050 Forward-Curved 10.3 10.0
Air Foil 10.3 10.1
YPAL051 Forward-Curved 10.2 9.9
Air Foil 10.2 10.0
YPAL060 Forward-Curved 10.1 9.8
Air Foil 10.1 9.9
YPAL061 Forward-Curved 10.1 9.8
Air Foil 10.1 9.9
TABLE 4 – EFFICIENCY RATINGS CV
IEER VAV IEER
Model IPLV
YPAL050 10.9 11.3 13.5
YPAL051 10.6 11.2 13.1
YPAL060 10.4 11.0 13.4
YPAL061 10.3 10.8 13.2

FORM 100.50-EG5 (108)
17
JOHNSON CONTROLS
The information below should be used to assist in
application of product when being applied at altitudes
at or exceeding 1000 feet above sea level.
The airflow rates listed in the standard blower perfor-
mance tables are based on standard air at sea level.
As the altitude or temperature increases, the density
of air decreases. In order to use the indoor blower
tables for high-altitude applications, certain corrections
are necessary.
Theexamplesbelowwillassistindeterminingtheairflow
performance of the product at altitude.
Example 1: What are the corrected CFM, static
pressure, and BHP at an elevation of 5,000 ft. if the
blower performance data is 6,000 CFM, 1.5 IWC and
4.0 BHP?
Solution: At an elevation of 5,000 ft, the indoor blower
will still deliver 6,000 CFM if the RPM is unchanged.
However, Table 7 must be used to determine the static
pressure and BHP.
Since no temperature data is given, we will assume an
air temperature of 70°F. Table 7 shows the correction
factor to be 0.832.
Corrected static pressure = 1.5 x 0.832 = 1.248 IWC
Corrected BHP = 4.0 x 0.832 = 3.328
Altitude and Temperature Corrections
A centrifugal fan is a “constant-volume” device. This
means that if the RPM remains constant, the CFM de-
livered is the same regardless of the density of the air.
However, since the air at high altitude is less dense,
less static pressure will be generated and less power
will be required than a similar application at sea level.
Air-density-correction factors are shown in Table 7 and
Figure 2.
Example 2: Asystem,locatedat5,000feetofelevation,
is to deliver 6,000 CFM at a static pressure of 1.5”. Use
the unit blower tables to select the blower speed and
the BHP requirement.
Solution: As in the example above, no temperature
information is given so 70°F is assumed.
The 1.5" static pressure given is at an elevation of
5,000 ft. The first step is to convert this static pressure
to equivalent sea-level conditions.
Sea-level static pressure = 1.5 / 0.832 = 1.80"
Entertheblowertableat6000sCFMandstatic pressure
of 1.8”. The RPM listed will be the same RPM needed
at 5,000 ft.
SupposethatthecorrespondingBHPlistedin the blower
table is 3.2.
This value must be corrected for elevation.
BHP at 5,000 ft = 3.2 x .832 = 2.66
TABLE 7 – ALTITUDE-CORRECTION FACTORS
Air
Temp Altitude (feet)
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
40 1.060 1.022 0.986 0.95 0.916 0.882 0.849 0.818 0.788 0.758 0.729
50 1.039 1.002 0.966 0.931 0.898 0.864 0.832 0.802 0.772 0.743 0.715
60 1.019 0.982 0.948 0.913 0.880 0.848 0.816 0.787 0.757 0.729 0.701
70 1.000 0.964 0.930 0.896 0.864 0.832 0.801 0.772 0.743 0.715 0.688
80 0.982 0.947 0.913 0.880 0.848 0.817 0.787 0.758 0.73 0.702 0.676
90 0.964 0.929 0.897 0.864 0.833 0.802 0.772 0.744 0.716 0.689 0.663
100 0.946 0.912 0.88 0.848 0.817 0.787 0.758 0.730 0.703 0.676 0.651

JOHNSON CONTROLS
18
FORM 100.50-EG5 (108)
FIG. 2. ALTITUDE/TEMPERATURE CONVERSION FACTOR

FORM 100.50-EG5 (108)
19
JOHNSON CONTROLS
Cooling Performance Data — 050 Model
TABLE 8 – COOLING PERFORMANCE DATA* - 50 TON (STANDARD CAPACITY)
* Rated performance is at sea level. Cooling capaciites are gross cooling capacity.
Air on
Evaporator Coil Temperature of Air on Condenser Coil
85°F 95°F
CFM WB
(°F)
Total
Cap.1
(MBH)
Total2
Input
(kW)
Sensible Capacity (MBH)
Return Dry Bulb (°F) Total
Cap.1
(MBH)
Total2
Input
(kW)
Sensible Capacity (MBH)
Return Dry Bulb (°F)
86 83 80 77 74 71 68 86 83 80 77 74 71 68
12000
73 684 45 402 364 324 287 247 - - 653 50 390 352 312 275 235 - -
67 618 44 485 446 407 368 329 289 249 590 49 471 433 394 355 317 277 237
62 574 43 562 520 476 437 397 358 318 550 48 549 508 465 423 384 345 305
56 571 43 571 555 539 523 484 442 400 550 47 550 534 518 502 471 428 386
14000
73 702 45 428 385 341 296 252 - - 670 50 415 372 329 284 240 - -
67 636 44 523 479 434 390 345 299 254 608 49 514 466 421 377 332 287 241
62 604 44 604 568 518 469 424 378 333 581 48 581 555 506 456 410 365 320
56 603 43 603 586 568 551 526 476 427 581 48 581 563 546 529 511 463 413
16000
73 716 46 452 404 355 305 255 - - 683 50 439 391 343 292 243 - -
67 652 45 565 510 460 410 360 309 258 623 49 555 497 447 397 347 296 245
62 632 44 632 612 559 500 448 397 346 607 48 607 589 545 489 435 384 333
56 631 44 631 612 593 575 556 511 453 606 48 606 588 569 551 533 498 441
18000
73 728 46 475 421 368 312 258 - - 694 50 462 409 355 300 246 - -
67 666 45 605 539 484 429 374 317 261 636 49 594 531 471 415 360 304 248
62 655 44 655 635 596 533 472 415 359 629 49 629 610 583 521 458 402 345
56 654 44 654 634 614 595 575 544 481 629 48 629 609 589 570 551 529 466
20000
73 737 46 496 438 380 320 260 - - 702 50 483 425 367 307 248 - -
67 679 45 646 574 507 446 386 325 264 649 49 633 560 493 433 373 311 251
62 675 44 675 654 632 564 494 432 370 648 49 648 628 607 552 480 418 357
56 674 44 674 653 632 612 592 572 506 647 49 648 627 607 586 567 547 492
22000
73 744 46 516 453 391 326 262 - - 709 51 503 440 378 313 250 - -
67 692 45 682 604 528 463 398 334 266 665 49 665 592 514 449 385 320 253
62 692 45 692 670 649 594 515 448 381 665 49 665 643 622 581 506 434 367
56 691 45 691 670 648 627 606 585 531 664 49 664 643 621 601 580 560 518
24000
73 751 46 535 468 401 332 264 - - 715 51 521 454 388 319 252 - -
67 708 45 708 637 548 478 409 340 269 680 50 680 626 534 465 396 327 256
62 707 44 708 685 663 624 540 463 391 679 49 679 657 635 610 526 449 377
56 707 44 707 684 662 640 618 597 555 678 49 678 656 635 613 592 571 541
105°F 115°F
12000
73 619 55 376 338 299 261 222 - - 580 61 360 323 285 246 207 - -
67 558 54 457 418 380 341 303 263 223 524 60 444 403 364 326 287 248 209
62 526 53 526 493 450 409 369 330 291 499 59 499 478 436 393 254 314 275
56 526 53 526 510 494 478 456 413 371 499 59 499 483 468 453 438 398 355
14000
73 634 55 401 358 315 270 226 - - 594 61 386 343 300 255 211 - -
67 575 54 499 451 407 362 318 273 228 540 60 486 435 391 347 302 257 212
62 555 53 555 538 492 443 395 350 305 526 59 527 510 477 427 379 334 289
56 555 53 555 538 521 504 487 449 398 526 59 526 509 493 476 460 433 384
16000
73 646 55 425 377 329 278 229 - - 604 61 409 361 313 263 214 - -
67 589 54 540 486 432 382 332 281 231 553 60 527 470 416 366 316 266 215
62 580 53 580 561 532 474 420 369 318 549 59 549 531 514 460 403 353 302
56 579 53 579 561 543 525 507 483 426 548 59 548 531 513 496 478 461 411
18000
73 655 56 447 394 341 286 232 - - 613 62 431 378 325 270 216 - -
67 603 55 580 516 455 400 346 289 234 568 60 565 503 439 384 329 273 219
62 600 54 600 581 562 507 443 403 330 568 60 568 549 531 492 429 370 314
56 600 54 600 580 561 543 524 519 452 567 60 567 549 530 512 494 476 436
20000
73 663 56 468 410 353 293 234 - - 619 62 452 394 337 277 219 - -
67 618 55 618 548 478 418 358 298 237 585 60 585 534 461 401 342 282 221
62 618 54 618 598 578 538 468 403 341 584 60 584 565 545 522 451 386 325
56 617 54 617 597 577 558 538 519 478 584 60 584 564 545 526 507 488 461
22000
73 669 56 488 425 363 299 236 - - 625 62 471 409 347 283 221 - -
67 634 55 634 679 499 434 370 305 239 599 61 599 568 488 417 353 289 223
62 634 54 633 612 592 567 490 418 352 598 60 598 578 558 538 476 401 335
56 633 54 633 612 591 571 551 531 502 598 60 598 577 557 538 518 499 480
24000
73 674 56 506 439 373 308 238 - - 629 62 489 423 357 292 223 - -
67 647 55 647 614 526 449 380 312 241 611 61 611 590 514 433 364 295 225
62 647 55 647 625 604 583 514 433 362 611 61 610 590 569 549 498 416 345
56 646 55 646 625 603 582 561 540 521 610 61 610 589 568 548 528 508 489

JOHNSON CONTROLS
20
FORM 100.50-EG5 (108)
Cooling Performance Data — 051 Model
TABLE 9 – COOLING PERFORMANCE DATA* - 55 TON (HIGH CAPACITY )
Air on
Evaporator Coil Temperature of Air on Condenser Coil
85°F 95°F
CFM WB
(°F)
Total
Cap.1
(MBH)
Total2
Input
(kW)
Sensible Capacity (MBH)
Return Dry Bulb (°F) Total
Cap.1
(MBH)
Total2
Input
(kW)
Sensible Capacity (MBH)
Return Dry Bulb (°F)
86 83 80 77 74 71 68 86 83 80 77 74 71 68
12000
73 704 48 413 374 334 295 255 - - 672 53 400 361 321 283 242 - -
67 636 47 496 457 417 378 338 298 257 607 51 483 443 404 365 325 285 244
62 590 46 572 531 487 447 407 367 327 564 51 559 516 475 434 394 354 313
56 584 45 584 568 551 535 - - - 562 50 562 546 530 514 480 438 395
14000
73 723 48 441 396 351 305 259 - - 690 53 427 383 338 293 247 - -
67 655 47 537 492 446 401 355 309 262 624 52 523 478 433 387 342 296 249
62 619 46 619 579 530 481 435 389 342 595 51 595 565 515 467 421 375 329
56 618 46 618 600 582 565 537 487 439 594 51 594 577 559 542 522 474 424
16000
73 738 48 467 417 366 315 263 - - 704 53 454 404 353 302 250 - -
67 672 47 580 525 474 423 371 319 266 640 52 566 511 460 409 358 305 252
62 647 47 647 625 571 514 462 409 357 622 51 622 603 557 502 448 395 343
56 646 46 646 627 608 589 571 522 466 621 51 621 602 584 565 547 508 451
18000
73 750 49 492 436 381 323 266 - - 715 53 479 423 367 310 253 - -
67 686 47 621 557 501 443 386 328 269 656 52 606 543 487 429 372 314 256
62 671 47 671 651 611 548 487 429 370 645 51 645 625 596 533 473 415 356
56 670 47 670 650 630 610 590 556 494 644 51 644 624 604 585 566 541 479
20000
73 760 49 516 455 394 331 269 - - 724 54 503 442 381 318 256 - -
67 699 48 660 593 526 463 400 336 272 667 52 647 578 512 449 386 322 259
62 692 47 692 671 646 581 511 447 383 664 52 664 644 623 565 497 433 369
56 691 47 691 670 649 628 608 586 519 664 52 664 643 622 602 582 562 506
22000
73 768 49 539 473 407 339 272 - - 731 54 526 460 393 326 259 - -
67 711 48 698 622 550 482 414 344 275 681 52 681 611 536 468 400 332 262
62 710 47 710 688 666 610 534 465 395 682 52 682 660 638 597 519 451 381
56 709 47 709 687 665 644 622 601 546 681 52 681 659 637 616 596 575 531
24000
73 775 49 561 490 419 346 274 - - 737 54 547 477 405 333 261 - -
67 726 48 726 655 573 500 427 353 278 697 53 697 642 558 486 413 339 265
62 726 47 726 703 680 640 556 482 407 697 52 697 674 652 625 546 468 393
56 725 47 725 702 680 657 635 613 570 696 52 696 673 651 629 608 586 554
105°F 115°F
12000
73 636 58 385 347 307 268 228 - - 597 64 370 331 293 253 213 - -
67 574 57 467 429 389 350 311 270 230 539 63 454 412 373 334 295 255 214
62 539 56 539 502 460 418 379 339 299 511 62 511 486 445 402 362 323 283
56 538 56 538 522 506 490 464 422 380 510 62 510 495 479 464 448 406 364
14000
73 653 58 413 368 324 278 232 - - 611 65 397 352 308 263 217 - -
67 592 57 511 463 418 373 327 281 235 555 63 496 446 401 356 311 265 218
62 569 56 569 549 501 452 406 360 314 539 63 539 522 485 437 389 343 297
56 568 56 568 550 533 516 499 458 408 538 62 538 521 505 488 472 442 393
16000
73 665 59 439 389 339 287 236 - - 622 65 422 373 323 271 220 - -
67 606 57 553 495 445 394 343 290 238 569 64 537 482 428 377 326 274 222
62 594 57 594 575 542 486 432 380 328 562 63 562 544 524 471 415 363 311
56 593 57 593 574 556 538 520 493 437 561 63 561 543 526 508 491 473 421
18000
73 675 59 464 408 353 296 239 - - 631 65 447 392 336 280 223 - -
67 619 58 592 531 471 414 357 299 241 583 64 576 516 454 397 341 283 225
62 615 57 615 596 576 519 457 399 341 582 63 582 563 544 503 439 382 324
56 614 57 614 595 576 556 538 519 464 581 63 581 562 543 525 507 489 448
20000
73 683 59 487 427 366 303 242 - - 638 65 471 410 349 287 226 - -
67 633 58 630 565 496 434 371 307 244 599 64 599 549 478 417 354 292 228
62 633 57 633 613 593 550 480 417 353 599 64 599 579 559 533 466 400 336
56 633 57 633 612 592 572 553 533 490 598 64 598 578 559 539 520 501 472
22000
73 690 59 510 444 378 311 244 - - 644 65 493 428 362 295 228 - -
67 650 58 650 597 519 452 384 316 247 614 64 614 581 506 435 367 300 231
62 649 58 649 628 607 579 507 435 365 613 64 613 593 572 552 491 417 348
56 649 58 649 627 607 586 565 545 514 613 64 613 592 572 552 532 513 493
24000
73 695 59 532 461 390 318 246 - - 649 66 515 444 374 303 231 - -
67 664 58 664 626 547 470 397 324 249 627 64 627 605 533 453 380 307 233
62 663 58 663 641 620 598 528 452 377 626 64 626 605 584 563 515 434 359
56 663 58 663 641 619 598 577 556 534 625 64 625 604 583 563 542 522 502
* Rated performance is at sea level. Cooling capaciites are gross cooling capacity.