Zamel BULIK DRS-982H User manual

The push-button code setting
5
5a 5b
The sound type selection inside the push-button
6
Remove the chime from the socket outlet
2 3
Remove the chime cover
The chime code setting
4
PDH-991
PDH-227
PDB-233
Available BULIK Chime Versions
1
DRS-982H RT-236

WIRELESS CHIME BULIK WITH HERMETIC PUSH-BUTTON DRS-982H
• Perfectasadoorchime,arestaurant/hotel“reception”chime,aninternalrecalldevice,
• Thedoorchimeinstallationisnotneeded,
• Chimeconnecteddirectlyto230VACsocketoutlet,
• Usefulathome,arestaurant,ahotel,acompanyoffice,andforspecialcarepeople,
• Thepush-buttonbatteryoperated,
• Thepush-buttonisadaptedtochangeableweatherconditions,
• Usefulathome,arestaurant,ahotel,acompanyoffice,andforspecialcarepeople,
• Rangeofwork:150m*inopenarea,
• Possibilityofsettingtheuser’sindividualcode(16codestoselect),
• Possibilityofinteroperationwiththefollowingwirelesspush-buttonssimultaneously:PDH-991(hermetic,150m*operatingrange),PDH-227
(hermetic,100m*operatingrange)andPDB-233(thereceptionchime,100m*operatingrange),
• Itispossibletoincreasethenumberofthechimesandpush-buttons,ifneeded,
• Twosoundstoselect(apossibilityofidentificationofthepush-buttonpushed),
• Loudnessvolumecontrol,
• Opticalsignalling(LED)ofthechimesignalreceiving,
• Thepush-buttonwiththebuilt-inacousticsignalling,
• Chimesound:DING-DINGorDING-DONG,DING-DONG,
• Soundlevel:approx.85dB.
I. TECHNICAL DATA
WIRELESS CHIME BULIK DRS-982H
Soundlevel:approx.85dB
Coding:16channels
Powersupply:230VAC/50Hz
Stand-bypowerconsumption:1.8VA
Maximumpowerconsumption:2.8VA
Transmission:radio
Operatingfrequency:433.92MHz
Protectionclass:II
IPprotection:IP20
Chimesound:DING-DINGorDING-DONG,DING-DONG
Temperatureoperatingrange:0°C÷35°C
WIRELESS, HERMETIC PUSH-BUTTON PDH-991
Powersupply:MN21/23A12Vbattery
Transmission:radio
Operatingfrequency:433.92MHz
Transmitterpoweroutput:<5mW
Operatingrange:150m*inopenarea
Coding:16channels
Transmissionsignalling:acoustic
IPprotection:IP44
Temperatureoperatingrange:-20°C÷35°C
*Thegivenrangeconcernsopenedareaieperfectconditions,withoutobstacles.Ifbetweenthetransmitterandthereceiverobstaclesarefound,thenit
canbeexpectedsmallerrangefor:woodandplasterfrom5to20%,thebrickfrom20to40%,armedconcretefrom40upto80%.Bymetallicobstacles
applyingradiosystemsisn’tbeingrecommendedfromtheattentionforconsiderablelimitingtheradius.Alsooverheadandundergroundpowerlineshave
thenegativeinuenceontherangeofbigpowerandtransmittersoftheGSMnetworkputinthewalkingdistanceofdevices.
II. INSTRUCTION MANUAL
a) How to launch the chime
1. Checkifthereisacompletesetinthepackage(thechime,PDH-991chimepush-buttonwithabattery,2plasticwallplugs+2screws,1
sectionofthedouble-sidedadhesivetape,impairedsealwithanoverprintonthechimebackwall).
2. Checkifvoltageinyoursocketoutletis230VAC.
3. Insertthechimeinto230VACsocketoutlet(Fig.2).
4. CheckiftheyellowLEDinthechimecasinglights.
5. Attheselectedpointplacethechimepush-buttonontothesubstrateandcheckitsoperationbymeansofpushingthepush-button.
6. Ifthechimeoperatescorrectly, fix the push-button at the previously selected place with the use of the wall plugs or the double-sided
adhesivetape.
b) The sound level adjustment
1. Remove,leveringitwiththeuseofascrewdriver,thelongitudinalcoverplacedonthechimefrontsidehorizontally.Therearethecode
switchesandthesoundleveladjustmenthandwheelunderthecover(Fig.3,4).
2. Adjustthesoundleveltoyourneedswiththehandwheel.
3. Placethechimeswitchescover.
c) Code changing
1. Allthechimeshavethesamefactorysetcode.Inordertoavoidautomaticchimestart(e.g.byyourneighbour)itisrecommendedtosetthe
user’sindividualcode.
2. Removethechimefromthesocketoutlet(Fig.2).
3. Withtheuseofascrewdriver,removetheflapoverthepush-buttonfrontpartandunscrewtwoscrewsundertheflap(Fig.5a).
4. DisassemblethecasingasshowninFig.5a.
5. Remove,leveringitwiththeuseofascrewdriver,thelongitudinalcoverplacedonthechimefrontsidehorizontally.Therearethecode
switchesandthesoundleveladjustmenthandwheelunderthecover(Fig.3).
6. Withtheuseofswitches1,2,3,4insidethechimeandthepush-buttonsetthesamecodeselectedbyyourself(Fig.4,5).
7. Placethechimeswitchesandthepush-buttoncover.
8. Insertthechimeintosocketoutlet
9. Checkthechimeoperationbymeansofpushingthepush-button.
10. Placethepush-buttoncasing,screwthescrewsandplacetheflap.
d) Sound type selection
1. Withtheuseofascrewdriver,removetheflapoverthepush-buttonfrontpartandunscrewtwoscrewsundertheflap(Fig.5a).
2. DisassemblethecasingasshowninFig.5a.
3. Withtheuseofswitches5and6insidethepush-buttonsettheselectedsoundtype.Please,remembertosettheswitchesindifferent
positions.Ifnot,thechimewillnotoperate(Fig.6).Ifyouhavetwopush-buttons,settwodifferentsoundtypesinordertorecognisewhich
onehasbeenpushed.
4. Checkthechimeoperationbymeansofpushingthepush-button.
5. Placethepush-buttoncasing,screwthescrewsandplacetheflap.
NOTE!
1. Thewirelesschimeisreadytouseafterapprox.10secondsafterinsertingintothesocketoutlet.
2. Thewirelesschimeisbeingoperatedwiththeuseofradiowaves.Therefore,ifthereareobstaclesonthesignalway(walls,metal/concrete
structures),thedeviceoperatingrangemaydecreasesignificantly.
3. Itisrecommendedtoavoidmountingthepush-buttondirectlyonametalsubstrate.
4. Ifthechimeoperatingrangeisinsufficient,youmayincreasetherangeby100m*withtheuseofRT-236retransmitterofZAMEL.Itis
recommendedtousetheretransmitterinhighvolumeroomsandcomplexshapeobjects.Ifneeded,itispossibletoincreasethenumberof
retransmittersinordertocoverthewholeobjectareaofanydimensions.
5. Ifanyautomaticchimestartsoccur,itmeansthatthereisanotherchimesystemintheneighbourhoodrunninginthesamechannel.Itis
necessarytochangethedevicecode.
6. Allthechimeshavethesamefactorysetcode.
The Declaration of Conformity is on our Website www.zamelcet.com
GB
ZAMELdevicesmarked
withthissigncanwork
witheachother