Zamel EXTA ED-1 User manual

ED - 1 SIGNALLING BELL INSTRUCTION MANUAL
Zakład Mechaniki i Elektroniki
ZAMEL sp.j.
J.W. Dzida, K. Łodzińska
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. [phone], Fax [phone]
www.zamelcet.com, e-mail: [email protected]
FEATURES
TECHNICAL DATA
DESCRIPTION
APPERANCE
ی Electromechanical bell,
ی Brass bell gong in a plastic casing,
ی Designed for acoustic signalling at
home and industrial systems,
ی Either surface-mounted or TH35 rail
mounted,
ی Double-module casing,
ی Sound level: approximately 68 dB.
The ED-1 electromechanical bell may be
used in various systems, where acoustic
signalling is needed (e.g. phase decay
signalling). The bell is designed for
mounting on TH35 rail.
The device should be
connected to a single-
phase system accordin-
gly to current standards.
The device connections
will be described in this
manual. Only qualied electricians are
allowed to mount, connect and adjust
the bell. It is necessary to read this ma-
nual before the device mounting. Do not
disassembly the timer casing or you will
lose any warranty rights and expose
yourself to the electric shock hazard.
Before mounting operation make sure
of disconnecting the connection wires
from the electric network. Use a cross-
head screwdriver of 3.5 mm diameter
to mount the device. The bell should
be carried, stored and used in an ap-
propriate way. Do not mount the bell in
case of any device parts lack, damage
or deformation. In case of malfunction
please notify the manufacturer.
ED - 1
Power terminals: L, N
Rated voltage: 230 V~
Rated voltage tolerance: -15 ÷ +10 %
Rated frequency: 50 / 60 Hz
Rated current: 4,5 VA
Switch-ON control: electromechanical bell
Connection terminals quantity: 2
Connection wire section: 0,2 ÷ 2,50 mm2
Operating temperature: 0 ÷ +35 oC
Operating position: optional
Casing fastening: TH 35 rail (accordingly to PN-EN 60715)
Casing IP: IP20 (PN-EN 60529)
Protection class: II
Overvoltage category: II
Pollution level: 2
Dimensions: double-module (35 mm) 90 x 35 x 66 mm
Weight: 92 g
Standard conformity: PN-EN 60669-1; PN-EN 60669-2-1
PN-EN 61000-4-2,3,4,5,6,11
Power terminals (L, N)
CAUTION

CONNECTIONS ASSEMBLY, OPERATION
APPLICATION
CASING DIMENSIONS
PRODUCT FAMILY
The ED-1 signalling bell is a member of
the EDM product family.
1. Disconnect the electric network by
means of an appropriate cut-off,
current-limiting circuit-breaker or
separator.
2. Check if there is no any voltage
between power leads by means
of an appropriate gauge.
3. Mount the bell on TH 35 rail.
4. Connect the system leads accor-
ding to the electrical diagram.
5. Connect power supply circuit.
The bell is ready to work just right
after its appropriate connecting. The
bell starts operation after supplying
the device. The device generates the
sound until it is supplied.
TIME DIAGRAMS UNIT DIAGRAM
Device version:
01 - continuous
operation
02 - erasable
1 - bell
Device type
EDM - xx
t
U
t
L
N
Control and L1 phase voltage drop
signalling circuit.
When L1 voltage drops below the value
preset on PNM-10 voltage relay (e.g.
200 V) the circuit will switch ON alarm
signal (the ED -1 bell).
NOTE: The bell is supplied from L2
phase. Therefore it is necessary to
maintain 230 V on this phase.
WARRANTY
The product warranty is for a period of 24 months
Dealer signature & stamp, purchase date
1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product.
2. The manufacturer’s guarantee does not cover any of the following actions:
a) mechanical damage during transport, loading / unloading or under other circumstances,
b) damage caused by incorrect product mounting or misuse,
c) damage caused by unauthorised modications made by the PURCHASER or any third parties to the product or any other devices
needed for the product functioning,
d) damage caused by Act of God or any other incidents independent of the manufacturer.
3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J.
4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation.
5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return.
6. The manufacturer’s guarantee is valid in the Republic of Poland.
7. The PURCHASER’s statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty.