230 V AC
• The sensor should be connected to the conductive elements such as metal casing of lighting ttings,
handles, door handles, etc. These elements must be electrically insulated.
• It is recommended that the surface to which the sensor is connected is as small as possible (it should
not exceed 25 dm2). If the surface increases more than 5 dm2the dierence in the touch sensitivity can
be observed.
• Switching on / switching o the circuits connected to the output terminals of the WDN-03 switch is
realised by a short touch of the item to which the sensor is connected.
• The sensor’s cable can be extended up to a maximum of 3 m with a minimum cross-section of 1 mm2.
Control in the switch on / switch off function: another short touching of the conductive part connected
to the sensor.
CAUTION! The WDN-03 switch connection to a single-phase installation must be installed in ac-
cordance with standards valid in a particular country. Installation, connection and control should
be carried out by a qualied electrician sta, who act in accordance with the service manual and
the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch-disconnector combined
to the proper circuit.
2. Check if there is no voltage on connection cables by means of a special measure equipment.
3. Connect the WDN-03 device to 230 V AC voltage.
4. Connect cables to proper terminal clamps of WDN-03 according to the connection diagram.
5. Mount the switch and the sensor on their nal place.
6. Switch on the power supply from the mains and check proper functioning of the device..
IMPORTANT:
If during the use of WDN-02 switch there is a need to change the sensor’s connection place, it
can be done without disconnecting the power supply. However it should be remembered, that in
each case after such an operation it is necessary to wait at least 10 seconds to perform the switch
automatic calibration process.
The WDN-03 device is used to switch on or switch o the light by means of a touch. The switch has a
sensor with 1,5 m long wire, which is connected to conductive components of lighting ttings or other
conductive elements having the function of a switch (metal handles, door knobs, metal railings, etc).
The WDN-03 switch is supplied with 230 V AC. It has one voltage output with a maximum load of 5 A /
250 V AC. Using the WDN-03 switch it is possible to switch on / switch o any traditional (conventional
light bulbs, halogens) and low-voltage (12 V AC halogens, LED diodes) light sources. In order to control
the low-voltage sources, it is necessary to connect an appropriate power supply or transformer system
to the switch output. WDN-03 has small casing dimensions and is designed for surface mounting with
a possibility to be screwed to it. It is recommended to use WDN-03 to control lighting in the kitchen
and bathroom furniture. The device can also be installed on ammable materials, e.g. wood, furniture
boards and plasterboard.
The switch features:
• low power consumption during stand-by mode (W) – the device is used to a continuous operation,
• relay output voltage 230 V AC,
• the relay contact with a maximum load of 5 A / 250 V AC,
• automatic calibration process referring to the change of the sensor’s connection place or the touch
surface,
• a possibility to control any light source,
• small dimensions,
• a possibility to screw to the mounting surface.
Nominal supply voltage: 230 V AC
Nominal power consumption: 0,9 W
Number of channels: 1 x wyjście napięciowe 230 V AC
Maximum channel capacity: 5 A for 250 V AC (1250 VA)
Znamionowe obciążenie obwodu wyjściowego: 300 W
Sensor’s length: 1,5 m
Section of sensor: 1 mm2
Number of terminal clamps: 6
Section of connecting cables: up to 2,5 mm2
Ambient temperature range: -10 ÷ +55 oC
Operating position: free
Casing mounting: surface - a possibility to screw to the mounting
surface
Casing protection degree: IP20
Protection level: II
Dimensions: 44 x 108 x 33 mm
Weight: 60 g
Reference standard: PN-EN 60669; PN-EN 61000
Sensor terminals
Output terminals
Terminals’ cover
Power supply terminals
12 V AC
14 V DC
TECHNICAL DATA
CAUTIONSMOUNTING
DESCRIPTION
DIAGRAM
APPEARANCE
Exemplary LEDIX series
lighting ttings
Sensor
connected to
a metal part of
the lighting
tting, lamp, grip
or a handle, etc.
ZNP, ZNN or ZNM
power supply
in 14 V DC version
ETZ or ETW series
transformer
in 12 V AC version
Halogen lamps
12 V AC
