ZAMST Thumb Guard Soft User manual

2017.10
How to apply - Illustrations
1
3
5
6 7 8
4
2
Outside Inside
Care Label
Finger Pocket
Front Rear Side
Thumb Guard Soft
Align the center line of the thumb
and the center of the stay cover.
Thumb Loop

Thank you for purchasing this product. For safety reasons, be sure to read this user manual before use,
and store it away for future reference.
Usage:
Hand (thumb) support
Read this first:
This product can be used for the left or right side.
Support may not be provided by this product under certain usage conditions.
This product cannot be used to treat thumb disease, disorder or injury.
Be sure the product size is correct before use. Refer to the size chart.
When using this product:
Due to the type of material used, wrinkles may appear to be scratches or other damage, but the quality
has not been compromised.
Due to the characteristics of materials used in this product, it may change colors in some storage
conditions.
When storing this product, do not hang excessive weight on its hook-and-loop fastener or raised fabric.
Doing so may weaken the hook-and-loop fastener capability.
Safety precautions are divided into the following sections, according to the level of danger involved.
WARNING: Using the product incorrectly may result in serious injury.
CAUTION: Using the product incorrectly may result in minor injury, or cause damage to property other
than this product.
WARNING
To prevent abnormalities or worsening of symptoms, those who suffer from the following conditions
should refrain from using the product.
-Those predisposed to allergies or with sensitive skin.
-Those who have a fracture, cut, numbness, swelling, eczema, rash, or other abnormality in the
area to be worn.
Be sure to follow the rules below and use the product correctly. If not used correctly, it could cause
circulatory issues or injury.
-Do not use this product for any parts other than thumb.
-Be sure the to use a product of the correct size. Refer to the size chart.
-Do not use while sleeping.
-When wearing the product for a long period of time, readjust as needed. Constant pressure for a
long period of time may cause skin or circulatory issues.
-Use up/down, inside/outside correctly.
-Follow the steps for wearing this product to use it correctly.
-Do not fasten the main body of the product too tightly.
-If the product loosens or comes off during use, be sure to refasten it correctly by following steps
from the beginning.
-If this product shows wear or damage or the hook-and-loop fastener no longer works well, do not
use it.
-Do not attempt to process, modify, or repair this product.
If any of the following abnormalities occur when using this product, immediately stop using the
product, and consult with a physician. Continued use may worsen symptoms.
-󱒅If it does not fit comfortably, etc.
-If an injury, fracture, cut, pain, numbness, swelling, eczema, rash, etc. occurs in the area the
product is worn.
Precautions for use - Be sure to read this:
ZAMST Thumb Guard Soft
INSTRUCTIONS FOR USE

This product can be washed in a washing machine. After washing, hang it in the shade to dry.
When washing this product, attach the hook-and-loop fastener to the main body of the product.
Attempting to wash this product without closing the hook-and-loop fastener may weaken its fastening
capability.
Do not use an iron or chlorine bleach. However, oxygen bleach can be used.
Do not use a dryer. Doing so may damage the product.
This product cannot be dry cleaned. Wet cleaning can be done, but avoid tumble drying.
How to apply:
Before attaching this product, carefully read through the [Precautions for use - Be sure to read this]. Then
follow the steps provided for proper attachment.
The attachment steps use the right hand for reference. The same principles apply to the left hand as well.
1. Remove all of the hook-and-loop fasteners of the main body of the product, and check over the
product's top/bottom, inside/outside (Illustration 1 and 2).
The side of the product to which the care label is attached is the underside; this is the side that will be
in contact with your skin.
2. Put your thumb through the thumb loop and adjust the position, as necessary (Illustration 3).
Align the center of your thumb with the center line of the stay cover (Illustration 4).
3. Gently pull the hook-and-loop fastener and fasten it to the raised fabric part of the product while
inserting your middle finger into the finger pocket of the product (Illustration 5).
4. Make sure the main body of the product(s) are not loose or improperly attached. If anything looks
unusual, start over from the beginning to reattach the product.
When attachment is completed (for right hand)
[Front diagram (Illustration 6)] [Rear diagram (Illustration 7)] [Side diagram (Illustration 8)]
Materials:
Fiber: Nylon, Polyester, Elastane
Non-fiber: Chloroprene, Polyurethane
* Note: When disposing of this product, be sure to follow all disposal ordinances and regulations as
specified by the local government.
Disclaimer:
* Product specifications, external view, etc. may be changed without prior notice for improvement
purposes.
* All possible measures were taken to ensure product quality, but if a defect, etc. is found, please contact
us.
CAUTION
Hard materials are used for the hook-and-loop fastener. In some rare cases, fingers or skin may be
damaged, so please use the product carefully.
Sweat and friction may cause this product's color to fade, or move to other materials.
Make sure the hook-and-loop fastener does not attach to clothing. Doing so may cause it to
become frayed or run.
CAUTION
Do not wash together with items faded in color. Doing so may cause the color to
fade or move to other materials.
When washing together with clothing etc., be sure to use a laundry net. If the
hook-and-loop fastener attaches to clothing, it may cause them to become
frayed or run.
Care and cleaning: