Zempire Inflatable Series User manual

INSTRUCTIONS
For a detailed description of all the features and specications
of this product please visit our website.
Tested in New Zealand. Made with care in China
Care Instructions -
1. Ensure guy ropes are out at all times during use
2. Never pack your tent away wet. If you must take your tent down when wet, ensure that it is dried
completely as soon as possible to prevent mildew forming
3. If mildew does form on your tent, wash o with warm water and a soft brush to prevent further growth,
do not use soap or detergents
4. Do not use an open ame inside your tent. The fabric has been treated with a re retardant but is in no
way re proof
5. Clean all pegs and poles before storing
6. This tent is not designed to withstand storm conditions. During strong winds, it is recommended that the
tent be taken down
7. Do not leave your tent pitched unnecessarily for extended periods of time, UV light damages the y and
will shorten the life of your tent
Condensation -
It is important that lower vents are opened at all times to reduce the risk of condensation. During humid or damp
conditions, it is recommended that inner door covers are opened to expose the mesh layer to allow additional
airflow throughout your tent.
Do not use foam squabs or non bonded mats directly on the tent floor. This will cause condensation between the
mat and floor and if not dried out can lead to mildew foaming.
5 Year Tent Guarantee -
Please take time to read about the protections we oer you
All our tents come with a guarantee designed to protect you as our valued customer. Flow Imports Ltd, the
makers of Zempire Camping Equipment tents, will repair or replace this tent, at their discretion should it fail due
to faulty materials or manufacture for a period of 5 years from the date of sale.
The Guarantee is subject to the following conditions:
1. The Guarantee only applies to an original purchaser who purchased this tent from an approved retail
outlet
2. The Guarantee does not apply if the tent has been used for anything other than reasonable personal
camping use. Commercial use (e.g. rental) or continuous use as a residence are expressly excluded
3. Damage due to normal wear and tear, accident, acts of God, negligence (other than by Flow Imports Ltd),
failure by the purchaser to ensure instructions for setting up and care are observed, deterioration due to
abnormal exposure to ultraviolet light, insect or mildew attack, or any other cause reasonably beyond the
control of Flow Imports Ltd are not covered
4. If redress is sought under the terms of this Guarantee, then the tent must be returned by the purchaser to
the outlet from where it was purchased within the Guarantee period, in a clean, dry state and with proof
of purchase
5. All transport costs and any other indirect costs are excluded from the Guarantee.
6. Flow Imports Ltd reserves the right to make a reasonable charge for repairs which it determines are not
within the scope of the Guarantee
7. The Guarantee does not limit, modify or exclude any rights under any law if doing so would contravene
that law or make any part of this Guarantee invalid. However, Flow Imports Ltd:
a) excludes (to the extent permitted by applicable law) all conditions and warranties that might otherwise
be implied; and
b) limits its liability for breach of any such condition or Guarantee that it cannot exclude together with its
liability under the Guarantee, to repairing or replacing the Goods or paying the cost of having the Goods
repaired or replaced (at Flow Imports’ option).
This tent has been made with meticulous care and attention to detail. Providing it’s properly looked after and
correctly stored, it will help you enjoy all that nature has to oer for years to come.
Get out more - you owe it to yourself.
JETFORCE

45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
1. Lay out your tent. Peg the 4 corners as
shown
2. Close o the 2 Taps on the right hand side
of the tent
3. Unscrew the cap on the Boston Valve
located on the right hand side of the front
tube. Connect the pump hose. Set up pump
as follows:
- Pump
- Pressure Gauge
- Pressure release Valve
- Hose
4. Inate to 9PSI.
NOTE - During hot weather it is
recommended that 7PSI is used
5. Close isolation taps inside the
tent
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
1. Open the two isolation
valves inside the tent
2. Remove and clean the awning poles. Do not
store poles inside each other
3. Open the two air release taps. These taps
should remain open during the packdown
process
4. Remove and clean all pegs
5. Fold awning over body of tent
6. Fold in 1/3s folding towards
the valves
7. Roll towards the door
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
6. Connect the steel awning poles together
- A1 to A2 (x4)
- RA to RB
- R5 to R4
7. Insert the R4 end of the ridge pole into the
rubber locator plug sewn onto the top
centre of the front air beam
8. Insert the spike of the RA / RB pole through
hole at end of R3 and then through eyelet
at end of awning. Extend the RA/RB pole
until the awning roof is level. Extend A5/A4
pole so awning sits taught
9. Insert spikes of A1 / A2 poles through
eyelets on either side of awning and guy
out at 45 degrees
11. Peg out all remaining peg points
R4
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
R5
RB
RA
A2
A1
JETFORCE
10. Peg out rear vent
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
45o
45o
PSI
0
1
2
3
456
7
8
9
10
CLOSE
CLOSE
MOVE INSIDE
45o
45o
OPEN
OPEN
1
2
3
4