Zempire NEO Series User manual

INSTRUCTIONS
For a detailed description of all the features and specications
of this product please visit our website.
Tested in New Zealand. Made with care in China
PITCHING INSTRUCTIONS - NEO 6
1. Ensure guy ropes are pegged out at all times during use
2. Never pack your tent away wet. If you must take your tent down when wet,
ensure that you dry your tent completely as soon as possible to prevent mildew forming.
3. If mildew does form on your tent wash o with warm water and a soft brush to prevent
further growth. Do not use detergents.
4. Do not use an open ame inside your tent. The fabric has been treated with a re retardant
but is in no way re proof
5. Clean all pegs and poles before storing
6. This tent is not designed to withstand storm conditions. During strong winds,
it is recommended that the tent be taken down
7. Do not leave your tent pitched unnecessarily for extended periods of time.
UV light damages the y fabric and will shorten the life of your tent
Flow Imports Ltd General Warranty
Subject to the exclusions and limitations set out below, Flow Imports Ltd will repair or replace
(at its choice) merchandise supplied by Flow Imports Ltd ( Goods) which fail due to faulty materials
and manufacture during the warranty period.
The following exclusions and limitations apply to the Warranty:
The Warranty does not apply except to an original purchaser who purchased
Goods new from a retail outlet.
The Warranty does not apply if:
(a) a dierent product specic warranty is provided by Flow Imports ltd; or
(b) the Goods are not made by Flow Imports Ltd and an express warranty is provided by
the maker of the Goods
The Warranty does not apply if the Goods have been used other than for reasonable personal
camping use. Use in a commercial context ( e.g. for rental or use by a commercial organization in
its business operations ) or continuous use in a domestic context are expressly excluded.
Damage due to reasonable wear and tear, accident, acts of God, negligence ( other than by
Flow Imports Ltd), failure by the purchaser to ensure instructions for use and care are observed,
deterioration due to abnormal exposure to the elements, insect or mildew attack, or any other
cause reasonably beyond the control of Flow Imports Ltd are all excluded.
Goods must be returned by the purchaser to the outlet from where they were purchased within
the Warranty period, in a clean state with proof of purchase.
All transport cost and any other indirect costs are excluded from the Warranty.
Flow imports Ltd reserves the right to make a reasonable charge for repairs which it determines
are not within the scope of the Warranty.
The Warranty does not limit, modify or exclude any rights under any law if to do so would
contravene that law or make any part of this Warranty invalid. However, Flow Imports:
(a) Excludes (to the extent permitted by applicable law) all conditions and warranties that might
otherwise be implied; and
(b) Limits its liability for breach of any such condition or warranty that it cannot exclude together
with its liability under Warranty, to repairing or replacing the Goods or paying the cost of
having the Goods repaired or replace ( at Flow Imports’ option).

6. Peg out all the peg points around the
inner tent. The peg points at
the base of each pole should be pegged
through the webbing loop rather than the
ring.
2x
2x
4. Thread the BLUE poles through
the pole sleeves on either side of
the dome you have just created.
Insert the pole ends into rings.
Attach the C clips around the
poles.
8. Attach the elastic loop over the
existing inner pegs. Where there is
no existing peg, peg the fly directly
into the ground ensuring there is
significant
space between the inner and fly.
9. It is recommended that guy
ropes are pegged out at all times
and windows are opened whenever
possible to allow adequate
ventilation.
Insert pegs at a 45oangle
3. Thread the RED poles through
the pole sleeves that run
diagonally across the centre of
the tent. Insert the ends of the
poles into the pins located below
each pole sleeve. Attach the C
clips around the poles
1. Clear your site making sure there are no
sharp objects where you are going to pitch
your tent. Try to get a site that is as flat as
possible. Spread out the inner tent (White),
the main door is located at the front.
2. Assemble the 5 pole sections.
Ensure that the poles do not snap
together.
1x
7. Pull the fly over the inner tent. The
ORANGE webbing loops indicate the
front of the fly. Connect the velcro
loops inside the fly around the cut
outs on the corresponding pole
sleeve.
5. Thread the GREEN poles through
the pole sleeve at the front of the
tent. Insert the pole ends into rings.
Attach the C clips around the poles.