Zenith HydroTap User manual

807134NZ v1.00 11.20 HydroTap Tap Instructions
USB Connected to the Tap.
Boiling out Red silicone tube from tap. Cut to length.
Chilled out
(BC, C) Blue silicone tube from tap,
(BCS, CS) Blue JG pipe from tap.
Cut to length.
Vent Clear silicone tube from tap. Cut to
length.
Sparkling out White JG pipe from tap. Cut to length.
Ambient out Blue JG pipe from tap. Cut to length.
Command Centre connections
6
7Cleaning and general maintenance
• Wipe surfaces with a damp cloth and then wipe dry
with a clean, dry cloth.
IMPORTANT - For Touch-Free Wave Tap:
• Do not use air-drying disinfectant sprays.
• Do not use abrasives to clean the sensor lenses at
the sides, top and rear of the Touch-Free Wave Tap.
• This could cause permanent malfunction and void
warranty.
Installation instructions
Wave, Elite, Classic Plus, Classic
B, BA, BC, BCS, CS, C
5Familiarise yourself with the tap connections
RED
boiling
tube
(BC,
B only)
BLUE
Chilled
tube
(BC, C only)
CLEAR
Vent
tube
(BC,
B only)
Boiling,
Boiling chilled,
Chilled
USB
Chilled sparkling
Boiling
chilled sparkling
Boiling
ambient
RED
boiling
tube
CLEAR
Vent
tube
USB
BLUE
JG
pipe
WHITE
JG
pipe
WHITE
JG
pipe
BLUE
JG
pipe
USB
RED
boiling
tube
CLEAR
Vent
tube
USB
BLUE
JG
pipe
!
Visit our website to
download the manuals
Zenith
HydroTap
zenithwater.co.nz
Zenith Heaters Limited
IRD/GST No. 95 640 729
18 Kawakawa Place,
Westgate, Auckland 0814
New Zealand
Ph +(64 9) 838 8612
Free Call 0800 558 055

Using these instructions
Position the tap such that it
dispenses into the sink
bowl with clearance for a
cup or tea pot.
Wave Tap: Observe
100mm 360⁰ clearance
envelope.
Ensure that taps are positioned to minimise
the risks of scalding when dispensing
boiling water.
!
1
Position Command Centre
and Tap as close together
as possible. See below.
Cut the hole & fit the spacer
• Cut a Ø35mm hole in the worktop / sink.
Ø35mm
• Apply a light smearing of silicone sealant on the
underside of the spacer to ensure a watertight fit.
Please refer to all safety and installation requirements
detailed in the Quick start guide provided with the
HydroTap Command Centre, and HydroTap Command
Centre installation instructions found online, prior to
installation of, or any change to, the complete system.
Before commencing the
installation,download
& read the HydroTap
Command Centre
installation instructions
!
Read the
instructions
WARNING
Tools needed for tap installation
In addition to normal tools, the following (or equivalent
equipment) will be required.
• 35mm diameter sheet metal hole punch for sinks.
• 35mm diameter hole saw for worktops.
• Tube spanner for fixing the tap assembly (supplied).
Water supply pressure requirements
2
116mm
125mm
225mm with
extension
Black
plastic spacer
Positioning
100mm
Wave clearance
100mm
100mm
100mm
Min - Max pressure, kPA (bar)
HydroTap 170 (1.7) - 700 (7.0)
Sparkling
HydroTap 250 (2.5 ) - 700 (7.0)
Booster 200 (2.0) - 700 (7.0)
Be aware of the risks of hazards which could
cause harm when using tools. Assess the
risks before starting the installation.
!
BC Compact
InLine
ELECTRONIC
3
Black
plastic spacer
Mount the tap
Pass the tubes and USB cable through the Ø35mm
hole.
Fixing
washer
Spider
clamp
Fixing nut
4Secure the tap
Use a tube spanner to secure the tap in place.
USB