Zenna Home BBHB75 User manual

Pg 1of 10 IS0090-I
©2013 Zenith Products Corp.
MCS 11/5/2013
Before You Begin:
Thank you for purchasing this product. Please identify all parts and hardware pieces before you begin.
When laying out parts, place them on a soft surface to prevent scratching.
Assembly instructions - BBHB75, BBHB75AN (Bronze) / BBN75, BBN75AN (Satin Nickel)

Pg 2of 10 IS0090-I
Tools Needed:
List of Parts:
(B) 3 shelves
(C) 2 legs (1 right and 1 left)
(G) 2 front tubes
(F) 2 rear tubes
(D) 2 front leg extensions
(H) 1 bottom brace
(A) 1 top piece
(E) 2 rear leg extensions

Pg 3of 10 IS0090-I
(1) 8 large screws
(3) 4 small screws
(5) 2 mounting screws
(2) 6 medium screws
(4) 8 end caps
(6) 2 wall anchors

1.Fasten front leg extensions (D) to the
front of legs (C), using small screws (3).
Fasten rear leg extensions (E) to the rear
of legs (C), using small screws (3).
Pg 4of 10 IS0090-I
NOTE:rear leg extensions (E)
have holes; front leg exten-
sions (D) do not have holes
Front
Parte frontal
Avant
Rear
Parte posterior
Arrière
3
IMPORTANT:
Be sure to orient legs (C) so
that the screw holes for the
small screws (3) are located
on the BACK of legs (C).
C
D
E

Pg 5of 10 IS0090-I
2.Insert end caps (4) into front and rear leg
extensions (D,E).
GF
3.Insert a front tube (G) and a rear tube
(F) to each leg assembly.
4
D
E
Be sure to orient front tube (G) so
that the end with the “dimpled”
hole (hole with a slight indent
surrounding it) is on the top.

Fasten 2 shelves (B) to the leg assem-
blies. NOTE:Crosswires should be on the
bottom of the shelf.
4.
IS0090-I
Pg 6of 10
2
NOTE:If these screw holes do
not line up with the screw holes
in shelves (B), then legs (C) need
to be switched with each other.
B
1
NOTE:The cross wires
should be on the bottom.

Pg 7of 10 IS0090-I
5.Insert top piece (A) into top rear tubes (F).
F
A
6.Fasten top shelf (B) to the assembly.
B
1
2

IS0090-I
Insert end caps (4) into front tubes (G)
and top piece (A).
7.
Pg 8of 10
4
G
8.Place unit in desired location. Attach the
bottom brace (H) to the assembly, using
large screws (1).
B
A
H
1

IS0090-I
9.Mount the unit to the wall.
Pg 9of 10
WARNING:FOR SAFETY REASONS, IT IS
IMPERATIVE THAT THIS UNIT BE MOUNTED
TO THE WALL. WE HAVE PROVIDED
MOUNTING HARDWARE FOR YOUR
CONVENIENCE.
Mounting Instructions:
Warning: Before cutting, drilling or
hammering into any wall surface, verify
the location of electrical, plumbing and
gas lines. Cutting any of these may
cause serious injury.
1. Mark mounting points on wall through
holes in the rear tubes of the unit.
2. Hammer wall anchors (6) into wall,
unless mounting screws (5) will go directly
into a stud. (NOTE: Do not use a wall
anchor if mounting screw will be going
into a stud.) Wall anchors (6) should be
oriented with the flat side horizontal.
3. Place unit against wall, lining up wall
anchors (6) and holes in rear tubes.
4. Complete mounting by tightening
mounting screws (5) into studs or wall
anchors (6).
5
6
Wall anchors (6) should be oriented with the flat side horizontal.
For safety reasons, it is
imperative to use a
stepladder.

Pg 10 of 10 IS0090-I
Assembly instructions - BBHB75 (Bronze) / BBN75 (Satin Nickel)
1.Slide hook body down onto hangers. Make
sure hook
body slides between hanger wires.
Hanger must slide betweeen two wires on either end of
hook body.
2.
Learn more about other home bath & faucets by Zenna Home on our website.