Zennio Roll-ZAS User manual

Roll-ZAS
KNX Room Controller
ZN1VI-TPZAS
Program: version 1.1
Manual: edition a
PRODUCT MANUAL

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
2
2
INDEX
Document updates ............................................................................................................................................... 3
1. Introduction.................................................................................................................................................. 4
1.1. ZAS........................................................................................................................................................ 4
1.2. Installation............................................................................................................................................ 5
2. Configuration ................................................................................................................................................ 8
2.1. Roll-ZAS application.............................................................................................................................. 8
2.2. Touch Area............................................................................................................................................ 9
2.3. Page navigation .................................................................................................................................. 10
2.4. ZAS IR control ..................................................................................................................................... 12
3. ETS Parameterization.................................................................................................................................. 14
3.1. Default configuration ......................................................................................................................... 14
3.2. General ............................................................................................................................................... 15
3.3. Pages................................................................................................................................................... 21
3.3.1. Pages 1-4 .................................................................................................................................... 23
a) Pair buttons ............................................................................................................................................ 24
b) Individual buttons .................................................................................................................................. 28
3.3.2. Configuration page ..................................................................................................................... 30
3.3.3. Security page .............................................................................................................................. 32
3.3.4. Indicators page ........................................................................................................................... 34
3.3.5. Screensaver ................................................................................................................................ 35
3.4. Inputs.................................................................................................................................................. 36
3.4.1. Switch/Sensor............................................................................................................................. 36
3.4.2. Temperature probe .................................................................................................................... 37
3.4.3. Movement detector ................................................................................................................... 38
3.5. Thermostats........................................................................................................................................ 39
3.6. Presence simulation ........................................................................................................................... 40
Annex I. Button icons.......................................................................................................................................... 42
Annex II. Communication objects....................................................................................................................... 43

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
3
3
DOCUMENT UPDATES
Version
Modifications
Page(s)
1.1a
Changes since version 1.0 of the application program:
Use of the central area of the touch panel as a binary control.
-
Introduction: brief explanation about the new functionality in the “Roll-
ZAS” application program.
5
Changes in the factory defaults. Possibility to enter the programming mode
from the buttons of the touch panel.
6
Section 2.4: note added on the use of the remote control.
13
Section 3.3: screenshot updated; information added about using the
central area of the touch panel as a binary control.
22,23
Section 3.3.5: information added about parameter “Execute Page 1 actions
at screensaver exit?”.
36
Annex II: object 246 “[General] Central Button” added.
45
General improvement of this English version of the manual –texts and
minor issues.
-

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
4
4
1. INTRODUCTION
1.1. ZAS
Room controller ZAS (Zennio Analogue Screen) is a touch panel that includes a thermostat,
an IR receiver, and analogue/binary inputs. ZAS is a smart solution for demanding applications in
hotel rooms, apartments, offices, and in any other environment where it is necessary to control
climate, shutters, lights, scenes, etc.
Figure 1.1. ZAS Room Controller
The most relevant features of ZAS are shown below.
1.8" back-lighted display with 128 x 64 pixels
Temperature sensor with thermostat function
12 touch buttons
Screensaver showing current time and temperature (internally measured by ZAS or by an
external device), with a letter size suitable for being read from several meters away
Two opto-coupled inputs, configurable as switches/sensors, temperature sensors or
movement detectors.
Two different downloadable application programs to choose from:

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
5
5
ZAS: this application puts together all the functionality of the controller within a Menu,
which is divided into several submenus (Thermostat, Security, Scenes, etc.). It is possible
to configure the functionality of up to 8 buttons in total, which will carry out different
actions, according to the ETS configuration. Button actions do not vary while navigating
though the Menu. Moreover, every action over them is confirmed with an easily readable
pop-up. The whole functionality of this application can be checked in the corresponding
user manual, available at http://www.zennio.com.
Roll-ZAS: a more versatile application with an intuitive user interface and with a high
degree of usability, functionality and capacity. Information is divided into pages (up to a
total of 4 direct-action button pages, besides specific pages as Security, Configuration,
etc.). For every button page it is possible to configure up to 8 buttons, which will carry out
different actions, according to the ETS configuration. Moreover, starting with version 1.1,
it is also possible to use the central area of the touch panel as an additional binary
control, providing the user with a quick manner of, for example, turning a light source on
or off whenever it is required.
1.2. INSTALLATION
ZAS is connected to the KNX installation as any other KNX device, through the KNX
connector located at the back.
For installing ZAS, it is first necessary to fix the metallic piece into the squared/rounded standard
box where it is going to be installed, with the corresponding screws.
Next, the KNX bus and the input terminal must be connected using the corresponding connectors;
both terminals are located in the rear part of the device.
Once the inputs and the KNX bus are connected, the device is fitted into the metal platform with the
help of the included magnets.
Finally, it is necessary to check, from both sides, that nothing unless the ZAS outline can be seen
(the metal platform should be completely hidden by ZAS).
This device does not need any additional external power supply since it is powered through the
KNX bus.
In figure 1.2, the element outline of ZAS is shown.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
6
6
Figure 1.2. ZAS Element scheme
The programming button (3) is used to set ZAS into the programming mode, by means of a short
push (the programming LED lights in red).
Note: If this button is held while plugging the device into the KNX bus, ZAS will go into secure
mode. The LED blinks in red.
Apart from the programming button(3), and particularly when it turns to be inaccessible, it will be
possible to enter the programming mode from the touch interface itself. In the factory default state,
after being connected to the KNX bus and prior to any type of download, the device will show a
certain interface, with almost no functionality at all, which, however, will commute between pages
“1” and “C” (Configuration) by pressing the “Menu” button (upper left button). Under page “C”,
pressing button number 5 (labelled with the text “Prog. LED” in the screen) will be totally equivalent
to pressing the programming button (3).
Figura 1.3. Screens “1” and “C” in the factory state
1.-KNX connector
2.- Temperature sensor
3.- Programming button
4.- Programming LED
5.- Inputs (A/D)
6 - Magnet
7.- Touch box
8 - Display
9.- IR receiver
10. Central touch panel area
10

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
7
7
Once the download of the application program finishes, it is necessary to calibrate ZAS. The touch
calibration is carried out pressing buttons 1, 2, 7 and 8, in this order (the sequence is shown in
Figure 1.3). The Display screen will indicate the button to be pressed each time (only if a text string
associated to this process has been previously configured in ETS, under "General Labels". See
section 3.2).
Figure 1.3. Calibration sequence
To obtain more detailed information about the technical features of ZAS, as well as security and
installation information, please read the controller Datasheet, included in the original package of the
device and also available at: http://www.zennio.com.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
8
8
2. CONFIGURATION
2.1. ROLL-ZAS APPLICATION
The Roll-ZAS application allows controlling a series of functionalities in a domotic installation
in a simple and intuitive way.
There are several parameters that refer to the general functionality of the controller, such as:
luminosity, touch panel locking, initial update, internal sensor, contrast, buzzer sound, presence
simulation, etc.
Pages
The information shown in the Display is divided into pages. It is possible to enable and
configure up to a total of 4different button pages (Page 1-4), as well as the specific pages
Configuration, Security, Indicators and Screensaver. All of them are explained in detail in
section 3.3 Pages of this manual.
The access and navigation through the configured pages is explained in section 2.3.
Inputs
ZAS incorporates 2 opto-coupled inputs each of which may be individually configured as a
switch/sensor, atemperature probe or a movement detector. Depending on the selected
configuration, it is necessary to connect different external elements to the ZAS inputs: push
buttons or switches, temperature probes (like Zennio ZN1AC-NTC68) or movement sensors
(Zennio ZN1IO-DETECT).
Thermostats
ZAS allows enabling and configuring in an independent manner up to 2 thermostats, with the
"Building" functionality. How they work and the ETS configuration of this kind of thermostat is
detailed in the specific documentation "Zennio Building Thermostat", available at:
http://www.zennio.com.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
9
9
2.2. TOUCH AREA
ZAS incorporates 12 touch buttons for controlling all its functionality. Moreover, this is
complemented by the central area of the touch panel, which can also be used as a binary control.
See figure 2.1.
Figure 2.1. Touch Area
The first row of the touch panel consists of the following buttons:
Menu button: to navigate through the different pages of ZAS (only if this option is enabled
by parameter; see section 3.3).
Arrow buttons: to navigate through the different pages of ZAS (only if this option is
enabled by parameter; see section 3.3). Moreover, with the arrow buttons it is possible to
increase/decrease, one by one, the values of contrast, illumination and time of the Display
from the Configuration page, as well as establishing times for the timers (in the case of the
buttons configured with such purpose; see section 3.3.1).
OK Button: button to confirm and to select the desired option.
Under this first row, there are 8 more buttons, distributed into 4 rows of two buttons each. They can
be configured through ETS to operate either independently or in pairs, implementing joint functions.
They are direct-action buttons, i.e., they will carry out the parameterized action every time they are
pressed. The executed action will depend on the parameterization for the buttons in every enabled
page.
Touch Area

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com
10
10
Each button contains a central LED that lights on during the time the button is kept pressed, thus
making it clear that the key press has been detected. The illumination status of the LED can be
customized, choosing between a normal illumination or dependant on the associated
communication object status. (See section 3.3.1 for further information). No LED will on in the case
of the central binary control of the touch panel.
ZAS will emit a soft beep every time a control in the touch area is pressed, unless the buzzer has
been disabled through the corresponding object.
2.3. PAGE NAVIGATION
The Roll-ZAS application has an intuitive user interface that allows, through the use of
pages, knowing at any time the chosen functionality for every button of a page.
Figure 2.2 shows how the pages are represented in the Display.
Figure 2.2. Example of page representation in the Display
Header
In the left side of the header a name (configured by parameter. See section 3.3.1) will be
shown, which identifies the current page (“ROOM 2”, in the above sample picture).
In the right side a navigation scheme is shown, composed by the sequence of numbers and
letters "i 1234 C S":
"i" refers to the Indicators page.
"1 2 3 4" refer to the pages where the direct-action controls are.
"C" refers to the Configuration page.
"S" refers to the Security page.
Header
Buttons