Zennio ALLinBOX 1612 v2 User manual

➢
ALLinBOX 1612 v2/88/46/Hospitality
Multifunction device with power supply, KNX-IP Interface,
outputs, inputs, and logical module
ZPR1612V2
ZPR88
ZPR46
ZPRHP
USER MANUAL
Application program version: [1.5]
User manual edition: [1.5]_a
www.zennio.com

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
2
CONTENTS
Contents........................................................................................................................................ 2
Document Updates ....................................................................................................................... 3
1 Introduction .......................................................................................................................... 4
1.1 ALLinBOX 1612 v2 / ALLinBOX 88 / ALLinBOX 46 / Hospitality........................................ 4
1.2 Installation........................................................................................................................ 6
1.3 Start-Up and Power Loss.................................................................................................. 8
1.4 LED Indicators................................................................................................................... 9
1.5 Hard Reset to IP Factory Defaults .................................................................................. 11
1.6 Hard Reset power supply............................................................................................... 12
2 Configuration....................................................................................................................... 13
2.1 KNX to IP Interface ......................................................................................................... 13
2.2 Programmer ................................................................................................................... 14
2.2.1 Parallel Downloads................................................................................................. 15
2.3 Additional Individual Addresses (Tunneling Addresses)................................................ 17
2.4 General........................................................................................................................... 18
2.5 Inputs ............................................................................................................................. 21
2.5.1 Binary Input............................................................................................................ 21
2.5.2 Temperature Probe................................................................................................ 21
2.5.3 Motion Detector .................................................................................................... 21
2.6 Outputs........................................................................................................................... 22
2.6.1 ALLinBOX 1612 v2 / 88 / 46 ................................................................................... 22
2.6.2 ALLinBOX Hospitality.............................................................................................. 24
2.7 Thermostats ................................................................................................................... 25
2.8 Master Light ................................................................................................................... 26
2.9 Logic Functions............................................................................................................... 29
2.10 Scene Timing .................................................................................................................. 30
2.11 Manual Control Through IR Remote Control ................................................................. 32
2.12 NTP................................................................................................................................. 31
ANNEX I. Communication Objects............................................................................................... 36

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
3
DOCUMENT UPDATES
Version
Changes
Page(s)
[1.5] _a
New devices: ALLinBOX Hospitality
-
Changes in the application program:
Date/time synchronisation via NTP
Optimisation of the shutters, standard thermostat,
hospitality thermostat and logic functions modules.
37
[1.4] _b
New devices: ALLinBOX 88 y ALLinBOX 46.
-

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
4
1INTRODUCTION
1.1 ALLinBOX 1612 v2 / ALLinBOX 88 / ALLinBOX 46 / Hospitality
ALLinBOX 1612 v2 / ALLinBOX 88 / ALLinBOX 46 / ALLinBOX Hospitality are a versatile
KNX actuators featuring a wide variety of functions.
Functions
1612 v2
88
46
Hospitality
Relay Outputs
Shutter Channels
8
4
2

Individual Outputs
16
8
4
1
Fan Coil Modules
2
(2/4-pipe)
1
(2/4-pipe)
1
(2/4-pipe)
1
(2-pipe)
Inputs
Temperature Probes
12
8
6
6
Binary Inputs
12
8
6
6
Motion Detectors
12
8
6
6
Thermostats
Standard
4
4
4

Hospitality
4
4
4
2
In addition to these functions, there are others, common to all ALLinBOX:
20 customisable, multi-operation logic functions.
2 master light control instances for an easy, out-of-the-box control of a set of
luminaires (or functionally equivalent devices) one of which acts as a general
lamp and the others as secondary lamps.
Manual operation / supervision of the 16/8/4 relay outputs through infrared.
Scene-triggered action control, with an optional delay in the execution.
Relay switches counter.
Heartbeat or periodical “still-alive” notification.
IP interface

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
5
➢Up to 5 parallel connections from ETS for programming and monitoring.
➢High-capacity buffer
7 light indicators (LEDs): 2 state indicators for the power supply (power and
overload), 1 power supply factory reset indicator, 2 state indicators for the lines
(bus and Ethernet), 1 IP factory reset indicator, and 1 additional indicator for
the programming mode.
29V power supply and 640/320/250/250 mA respectively. It is divided
between an auxiliary output of 29V and a bus output with KNX coil include. The
nominal input of the power supply must be universal 110/230V ~ 50/60Hz.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
6
1.2 INSTALLATION
Figure 1. ALLinBOX 1612 v2 elements scheme.
Note: the above figure is entirely analogous for ALLinBOX 88, ALLinBOX 46 and
ALLinBOX Hospitality.
Figure 1 shows a scheme of ALLinBOX 1612 v2 with all the LED indicator and required
connections. ALLinBOX has its own power supply, so it does not need an additional one
and it serves to supply the rest of the devices through the KNX bus.
The couple LNX twisted-pair (TP) line and LAN network, the KNX bus (12) and Ethernet
(18) cables must be connected. After the connection, the device can be conveniently
mounted on the DIN rail by the usual procedure.
The main elements of the device are described below.
Test/Prog. Pushbutton (13): a short press on this button sets the device into
the programming mode, and the associated LED (14) lights in red.
9
2
5
4
8
1
6
7
3
10
16
11
12
13
14
15
16
17
18
19
1. Main Power Supply.
2. Overload Status LED.
3. Power Supply Status LED.
4. Reset Button.
5. Reset Status LED.
6. IP Factory Reset Button.
7. IP Factory Reset LED.
8. Ethernet LED.
9. KNX Bus LED.
10. Analog/Digital Inputs.
11. Auxiliary Power Output.
12. KNX Connector.
13. Programming/Test Button.
14. Programming/Test LED.
15. Fixing Clamp.
16. Outputs.
17. IR Input.
18. Ethernet Connector.
19. Remote Control (not included).

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
7
Note: if this button is held while plugging the device into the KNX bus, the
device will enter into safe mode. In such case, the LED will blink in red every
0.5 seconds.
Outputs (16): output ports for the insertion of the stripped cables of the
systems being controlled by the actuator (see section 2.6). Please secure the
connection by means of the on-board screws.
Inputs (10): input ports for the insertion of the stripped cables of external
elements such as switches / motion detectors / temperature probes, etc. One
of the two cables of each element need to be connected to one of the slots
labelled “1” to “12”/ “1” to “8” / “1” to “6”, while the other cable should be
connected to the slot labelled as “C”. Note that all the external input devices
share the “C” slot for one of the two cables. Please secure the connection by
means of the on-board screws.
LEDs (2, 3, 5, 7, 8 y 9) and reset buttons (4 y 6): the behaviour will be
described in section 1.4.
Main Power Supply (1): slots for the connection of the voltage wires (phase,
neutral and ground).
To get detailed information about the technical features of this device, as well as on the
installation and security procedures, please refer to the corresponding Datasheet,
bundled with the original package of the device and also available at www.zennio.com.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
8
1.3 START-UP AND POWER LOSS
During the start-up of the device, the Test/Prog. LED will blink in blue colour for a few
seconds before ALLinBOX is ready. External orders will not be executed during this time,
but they will do it afterwards.
Depending on the configuration, some specific actions will also be performed during the
start-up. For example, the integrator can set whether the output channels should switch
to a particular state and whether the device should send certain objects to the bus after
the power recovery. Please consult the next sections of this document for further details.
On the other hand, when a bus power failure takes place, ALLinBOX will interrupt any
pending actions and will save its state so it can be recovered once the power supply is
restored.
For safety reasons, if a power loss takes place, all shutter channels will be stopped
(i.e., the relays will open), while the individual outputs and fan coil contacts will switch to
the specific state configured in ETS (if any).

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
9
1.4 LED INDICATORS
ALLinBOX incorporates 7 LED lights on the top of the device that make it easy to
monitor the status of the buses and to detect typical communication problems, as
detailed below.
Figure 2. LEDs
KNX Line Status LED (TP): shows the status of the KNX bus.
➢OFF: KNX line is not powered.
➢ON (green) = KNX line is powered.
Note: the update of the LED status can be delayed a few seconds after the
trigger event, e.g., after the disconnection of the main power supply.
Ethernet Line Status LED (IP): shows the status of the Ethernet line.
➢OFF: IP address missing, or IP line not connected.
➢ON (green): Ethernet connection OK and IP address correctly assigned.
Power Supply Status LED (POWER): shows the status of the power supply.
➢OFF: the device is not powered.
➢ON (green): device with voltage.
➢BLINKING (green): short circuit on the KNX bus / “Reset” button press.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
10
Overload LED (OVERLOAD): notifies a high consumption on the KNX bus
and/or the auxiliary power output line.
➢OFF: normal power consumption on the KNX bus and/or the auxiliary power
output line.
➢ON (red): overload on bus KNX and/or auxiliary power output line *.
➢BLINKING (red): cut-off due to overload on the KNX bus and/or the auxiliary
power output line *.
* Reduce the load on the bus and/or the auxiliary power output lines until its
total consumption does not exceed the maximum current specified.
Programming LED:
➢OFF: normal operation.
➢ON (red): programming mode active.
➢BLINKING (red): safe mode active.
➢ON (green): test mode active.
➢BLINKING (blue): the device is initializing.
IP Factory Reset LED:
➢OFF: normal operation.
➢ON (red): IP restored by DHCP.
➢ON (green): static IP (of ETS configuration) restored.
➢ON (yellow): IP restored by APIPA.
Note: Please refer to section 1.5 for further details.
Reset LED:
➢OFF: normal operation.
➢BLINKING (red): “Reset” button is pressed / short circuit on the KNX bus.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
11
1.5 HARD RESET TO IP FACTORY DEFAULTS
The objective of the IP factory reset is to locate a device that is not accessible on a local
network due to an IP configuration loss. Once the device is accessible, it will be
necessary a new ETS download to introduce the desire IP configuration.
By pressing the "IP Factory Reset" button for three seconds:
The device will adopt an IP address via the DHCP server.
➢If the DHCP client does not obtain a valid IP address (after several
attempts), then the device will be assigned an IP address via the AutoIP
(APIPA)
1
protocol.
The factory reset indicator LED will light up in red.
If a second-long press is made on the "IP Factory Reset" button
The device will adopt a static IP address.
➢If "Use a static IP address" has been chosen on the ETS configuration, the
device will have the configured IP.
The factory reset led will light up in green.
➢On the other hand, if on the ETS configuration "Obtain an IP address
automatically" has been chosen, the device will obtain an IP by means of
AutoIP (APIPA).
The factory reset indicator LED lights up in yellow.
The factory IP setting and the colour of the factory reset LED will remain until the device
is restarted.
The following table summarizes the above:
Press
ETS Configuration
IP Configuration
LED
1st long press
(3s)
Obtain an IP automatically
IP obtained by DHCP.
(If a valid IP is not obtained →
IP by APIPA)
Red
Use a static IP address
2nd long
Obtain an IP automatically
IP obtained by APIPA
Yellow
1
Random static IP configuration in the range 169.254.1.0 - 169.254.254.255

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
12
press (3s)
Use a static IP address
Static IP of ETS configuration
Green
1.6 HARD RESET POWER SUPPLY
If “Reset” button is pressed, a short circuit is made in the output power supply (29V).
The device will not restart (and will not give power) until the button is released. The
power supply status LED (POWER) will blink in green, and the Reset status LED will
blink in red while the button is being pressed.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
13
2CONFIGURATION
To begin with the parameterisation process of the device, it is necessary, once the ETS
program has been opened, to import the database of the product. Next, the device
should be added to the project where desired.
The configuration of this device is done both in the parameters tab and in the ETS
properties. The following sections explain how to configure each of the device
functionalities.
2.1 KNX TO IP INTERFACE
ALLinBOX is an interface device intended for the interconnection between a KNX bus
and an Ethernet network (LAN).
The network parameters can be configured in the "IP" panel of the ETS "Properties":
Figure 3 IP Configuration
Obtain an IP address automatically
2
.ALLinBOX will automatically take an IP
address whenever there is a DCHP server in the local network to which it is
connected.
2
The default values of each parameter will be highlighted in blue in this document, as follows:
[default/rest of options].

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
14
Use a static IP address. If DHCP protocol is not used, the following properties
must be set manually:
➢IP Address [0.0.0.0…255.255.255.255].
➢Subnet Mask [0.0.0.0…255.255.255.255].
➢Default Gateway [0.0.0.0…255.255.255.255].
Note: If a static IP is configured, it is important to make sure that no other
device on the network has this IP assigned to it and that it does not belong to
the DHCP range configured for the router, otherwise connection problems with
the ALLinBOX will be observed.
In addition, the following information will be shown:
MAC Address.
Multicast Address [224.0.23.12]: IP address (reserved by the IANA
organization for the KNXnet/IP protocol) used by ETS in this case, for
discovering the available KNX-IP interfaces within the same network.
Once these properties have been entered an ETS programming is required to download
the configuration to the device.
2.2 PROGRAMMER
ALLinBOX can be used in ETS as a programming interface. In addition to an IP
address, they must be assigned a KNX individual address for this purpose.
Up to five simultaneous connections are allowed for performing downloads or for bus
monitoring.
Note: to detect the ALLinBOX as a programmer in ETS, it needs to be connected to the
same IP network as the PC.
To use a device as a programmer simply select it in the ETS "Bus" tab under
Connections →Interfaces.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
15
Figure 4. Selection of ALLinBOX in the Bus Connections tab in ETS.
Or by selecting it at the bottom left after opening a project in ETS.
Figure 5. Selection of ALLinBOX in a ETS project.
Important: If the ALLinBOX is selected as the programming interface to program
itself it is recommended to first perform individual address download and then
application download, rather than a complete download (complete download causes
a device restart and therefore communication with ETS is lost and the download is
cancelled).
2.2.1 PARALLEL DOWNLOADS
ETS offers the option to perform multiple parallel downloads within the same project.
This option is only available for connections via a KNX-IP router or a KNX-IP interface.
Certain conditions must be met:
Each download must be performed on a different line.
For each line, it is necessary to select one ALLinBOX to perform the
download.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
16
Note: There is a restriction: parallel downloads are not available to download physical
addresses. When performing this type of downloads, the link device used by ETS is not
the one configured for the line but the general one.
In "Settings" panel, in “Properties” of the line, the connection can be selected.
Figure 6 ETS5 parallel downloads configuration.
Note: once the connection has been selected, it will not be available for the other lines.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
17
2.3 ADDITIONAL INDIVIDUAL ADDRESSES (TUNNELING
ADDRESSES)
ALLinBOX requires a specific individual address when acting as a programming
interface (tunnelling) other than the address of the device itself. Up to five simultaneous
connections are possible, which implies that up to five different individual addresses
must be configured.
After the individual ALLinBOX address has been set, the five tunnelling addresses are
automatically set with consecutive values. These addresses can be changed at any time.
Figure 7 Set tunnelling addresses.
Note: ALLinBOX tunnelling addresses must not match any of the addresses set to other
devices on the system.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
18
2.4 GENERAL
After importing the corresponding database in ETS and adding the device into the
topology of the desired project, the configuration process begins by entering the
Parameters tab of the device.
ETS PARAMETERISATION
The "General" tab contains general settings. From this screen it is possible to
activate/deactivate all the required functionality.
Figure 8. General screen
Inputs [disabled/enabled]: enables or disables the “Inputs” tab on the left
menu. See section 2.5 for more details.
Outputs [disabled/enabled]: enables or disables the “Outputs” tab on the left
menu. See section 2.6 for more details.
Thermostats [disabled/enabled]: enables or disables the “Thermostats” tab on
the left menu. See section 2.7 for more details.
Master Light [disabled/enabled]: enables or disables the “Master Light” tab on
the left menu. See section 2.8 for more details.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
19
Logic Functions [disabled/enabled]: enables or disables the “Logic Functions”
tab on the left menu. See section 2.9 for more details.
Scene Timing [disabled/enabled]: enables or disables the “Scene Timing” tab
on the left menu. See section 2.10 for more details.
Manual Control with IR [disabled/enabled]: enables or disables the “Manual
Control” tab on the left menu. See section 2.11 for more details.
Sending of Indication Objects (0 and 1) on Bus Voltage Recovery
[disabled/enabled]: this parameter lets the integrator activate two new
communication objects (“Reset 0” and “Reset 1”), which will be sent to the
KNX bus with values “0” and “1” respectively whenever the device begins
operation (for example, after a bus power failure). It is possible to parameterise
a certain delay [0…255] to this sending.
Figure 9. Sending of Indication objects on bus voltage recovery
Heartbeat (Periodic Alive Notification) [disabled/enabled]: this parameter
lets the integrator incorporate a one-bit object to the project (“[Heartbeat]
Object to Send ‘1’”) that will be sent periodically with value “1” to notify that
the device is still working (still alive).
Figure 10. Heartbeat.
Note: The first sending after download or bus failure takes place with a delay of
up to 255 seconds, to prevent bus overload. The following sendings match the
period set.

ALLinBOX 161 / 88 / 46 / Hospitality
https://www.zennio.com Technical Support: https://support.zennio.com
20
Show Relay Switches Counter Objects [disabled/enabled]: enables two
communication objects to keep track of the number of switches performed by
each of the relays ("[Relay X] Number of Switches") and the maximum
number of switches carried out in a minute ("[Relay X] Maximum Switches
per Minute").
Synchronize Clock Master via NTP [disabled/enabled]: enables or disables
the “NTP” tab in the tree on the left. For more information, see section 2.11.
Note: This parameter must be enabled in the device that will be clock master
so that there is only one clock master in the installation.
DNS Servers Configuration: numeric text fields to enter the IP address of two
DNS servers:
➢IP Address of DNS Server 1 and 2 [192.168.1.1, 192.168.1.2].
Note: The connection to the DNS server is necessary to ensure the correct
functioning of the NTP servers (see section 2.11). As long as there is no
connection to a DNS server, the date and time information will not be
synchronized.