ZIEHL-ABEGG Acontrol PXET6Q User manual

Acontrol
PXET6Q / PXET10Q
Multipurpose controller for variable voltage 1 ~ fans
Operating Instructions
Keep for reference!
Software version: B1061AA from version 1.01
L-BAL-E016-GB 1925 Index 007 Part.-No.
english
Библиотека СОК 

Content
1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Structure of the operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Exclusion of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Explanations of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 Requirements placed on the personnel / due diligence . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5 Start-up and during operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.6 Work on the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.7 Modifications / interventions in the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.8 Operator’s obligation of diligence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.9 Employment of external personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Operational area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.5 Disposal / recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2 Minimum space requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Outdoor installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.4 Installation location for agriculture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.5 Temperature influences during commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.2 EMC-compatible installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2.1 Motor cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2.2 Control cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2.3 Harmonics current for devices ≤ 16 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.3 Mains connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.4 Motor connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.4.1 Running noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.5 Motor protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6 Signal or sensor connection (E1 Analog In 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.7 Output voltage 0 - 10 V (A1 Analog Out 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.8 Voltage supply for external devices (+24V, GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.9 Digital input (Digital In 1 D1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.9.1 Enable, device ON / OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.9.2 Reverse action of control function (only for P-Controller / PI-Controller) . . . . . . . . . . 12
5.10 Relay outputs (K1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.11 Potential at control voltage connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6 Operating and display elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 Main switch and potentiometer with integrated light signal . . . . . . . . . . . . . . . . . . . . . . 13
6.2 Internal Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operating Instructions Acontrol – model series PXET6Q / PXET10Q
L-BAL-E016-GB 1925 Index 007 Part.-No.
2/32

7 Base setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1 Programming of the desired function (Speed controller / P-Controller, PI-Controller) . . 15
7.2 Select operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.3 Function of dipswitches for operation as Speed controller 1.01 (DIP 1
| OFF | ) . . . . 16
7.4 Function of dipswitches for operation as P-Controller, PI-Controller, 2.01 , 3.01 , 4.01
(DIP 1 | ON | ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.5 Minimum speed cut off DIP 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.5.1 For mode Speed controller 1.01 .................................... 17
7.5.2 For operation as P-Controller, PI-Controller 2.01 , 3.01 , 4.01 . . . . . . . . . . . . . . . . 17
7.6 Hardstart function DIP 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1 Prerequisites for commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9 Setting for operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.1 Speed controller 1.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.1.1 Setting for operation as Speed controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.1.2 Diagram: setting signal and speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9.1.3 Operation with two variable output voltages (two steps) . . . . . . . . . . . . . . . . . . . . . 19
9.2 Temperaturre control (P-Controller) 2.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.2.1 Setting for operation as Temperature controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.2.2 Example Temperature control “Cooling function” (factory setting) . . . . . . . . . . . . . . 21
9.2.3 Example Temperature control “Heating function” .......................... 21
9.3 Pressure control condensers (P-Controller) 3.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9.3.1 Setting for operation as Pressure controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9.3.2 Example Pressure control condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9.3.3 Setting with refrigerant medium table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.4 Pressure control, Air velocity control (PI-Controller) 4.01 . . . . . . . . . . . . . . . . . . . . . . 25
9.4.1 Setting for operation as Pressure and air velocity controller . . . . . . . . . . . . . . . . . . 25
9.4.2 Example: Pressure control for ventilation systems . . . . . . . . . . . . . . . . . . . . . . . . 25
9.4.3 Example: Air velocity control for clean rooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10 Diagnostics / Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.1 If controller doesn´t work correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11 Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11.1 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11.1.1 Performance reduction during elevated ambient temperatures . . . . . . . . . . . . . . . . 28
11.2 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11.3 Dimensions [mm] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11.4 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
11.5 Manufacturer reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
11.6 Service information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Operating Instructions Acontrol – model series PXET6Q / PXET10Q
L-BAL-E016-GB 1925 Index 007 Part.-No.
3/32

1 General notes
Compliance with the following instructions is mandatory to ensure the functionality and safety of the
product. If the following instructions given especially but not limited for general safety, transport,
storage, mounting, operating conditions, start-up, maintenance, repair, cleaning and disposal / recy-
cling are not observed, the product may not operate safely and may cause a hazard to the life and
limb of users and third parties.
Deviations from the following requirements may therefore lead both to the loss of the statutory material
defect liability rights and to the liability of the buyer for the product that has become unsafe due to the
deviation from the specifications.
1.1 Structure of the operating instructions
Before installation and start-up, read this manual carefully to ensure correct use!
We emphasize that these operating instructions apply to specific units only, and are in no way valid for
the complete system!
Use these operating instructions to work safely with and on the device. They contain safety instruc-
tions that must be complied with as well as information that is required for failure-free operation of the
device.
Keep these operating instructions together with the device. It must be ensured that all persons that
are to work on the device can refer to the operating instructions at any time.
Keep the operating instructions for continued use. They must be passed-on to all successive owners,
users and final customers.
1.2 Target group
The operating instructions address persons entrusted with planning, installation, start-up, mainte-
nance and servicing, who have the corresponding qualifications and skills for their job.
1.3 Exclusion of liability
Concurrence between the contents of these operating instructions and the described hardware and
software in the device has been examined. It is still possible that non-compliances exist; no guarantee
is assumed for complete conformity. To allow for future developments, construction methods and
technical data given are subject to alteration. We do not accept any liability for possible errors or
omissions in the information contained in data, illustrations or drawings provided.
ZIEHL-ABEGG SE is not liable for damage due to misuse, incorrect use, improper use or as a
consequence of unauthorized repairs or modifications.
1.4 Copyright
These operating instructions contain copyright protected information. The operating instructions may
be neither completely nor partially photocopied, reproduced, translated or put on data medium without
previous explicit consent from ZIEHL-ABEGG SE. Infringements are liable for damages. All rights
reserved, including those that arise through patent issue or registration on a utility model.
2 Safety instructions
This chapter contains instructions to prevent personal injury and property damage. These instructions
do not lay claim to completeness. In case of questions and problems, please consult our company
technicians.
2.1 Intended use
The equipment is to be used solely for the purposes specified and confirmed in the order.
Any other use above and beyond this is considered not for the intended purpose unless agreed
otherwise by contract. The manufacturer will not be liable for any damage resulting from this. The
individual or company using it bears the sole risk.
Reading these operating instructions and complying with all contained instructions - especially the
safety notifications contained therein - are considered part of intended use. To consider is also the
manual of attached components. Not the manufacturer, rather the operator of the device is liable for
any personal harm or material damage arising from non-intended use!
Operating Instructions Acontrol – model series PXET6Q / PXET10Q General notes
L-BAL-E016-GB 1925 Index 007 Part.-No.
4/32

2.2 Explanations of symbols
Safety instructions are highlighted with warning triangles and are depicted according to the degree of
hazard as follows.
Attention!
General hazardous area. Death or severe injury or significant property damage can occur if the
corresponding precautions are not taken!
Danger due to electric current
Danger by dangerous, electric voltage! Death or severe injury can occur if the corresponding
precautions are not taken!
Information
Important additional information and advice for user.
2.3 Product safety
The device conforms to the state of the art at the time of delivery and is fundamentally considered to
be reliable. The device and its accessories must only be used in a flawless condition and installed and
operated in compliance with the assembly instructions and/or operating instructions. Operating out-
side the device's technical specifications (see name plate and attachment / technical data) can lead to
a defect in the device and additional damage!
Information
In the case of a malfunction or a failure of the equipment check all functions with alarms in order to
prevent injury to persons or property. Note possibility of back-up operation. If used in intensive animal
environments, any malfunctions in the air supply must be detected as soon as possible to prevent the
development of a life-threatening situation for the animals. The design and installation of the system
must comply with local regulations and directives. In Germany these include DIN VDE 0100, the
animal protection and the keeping of working animals ordinance and the pig-keeping ordinance etc.
Also note the instructions of AEL, DLG, VdS.
2.4 Requirements placed on the personnel / due diligence
Persons entrusted with the planning, installation, commissioning and maintenance and servicing in
connection with the frequency inverter must have the corresponding qualifications and skills for these
jobs.
In addition, they must be knowledgeable about the safety regulations, EU/EC directives, rules for the
prevention of accidents and the corresponding national as well as regional and in-house regulations.
Personnel to be trained or instructed and apprentices are only permitted to work on the device under
the supervision of an experienced person. This also applies to personnel undergoing general training.
Comply with the legal minimum age.
2.5 Start-up and during operation
Attention!
•During commissioning, unexpected and hazardous conditions can arise in the entire installation
due to defective adjustments, defective components or incorrect electrical connections. Remove
all persons and objects from the hazardous area.
•During operation, the device must be closed or installed in a control cabinet. Fuses may only be
replaced by new ones and must not be repaired or bypassed. The data for the maximum line
fuse are to be considered absolutely (see Technical data). Use only fuses specified in schematic
diagrams.
•Any faults detected in the electric system/modules/operating equipment must be corrected
immediately. If these faults are not corrected, the device/system is potentially very dangerous.
The device/system must therefore not be operated when it is faulty.
•Pay attention to smooth, low vibration running of the motor/fan, the appropriate instructions in the
drive documentation must be observed!
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Safety instructions
L-BAL-E016-GB 1925 Index 007 Part.-No.
5/32

2.6 Work on the device
Information
Mounting, electrical connection, and start-up operation may only be carried out by an electrical
specialist in accordance with electrotechnical regulations (e.g. EN 50110 or EN 60204)!
Danger due to electric current
It is generally forbidden to carry out work on electrical live parts. Protection class of the device when
open is IP00! It is possible to touch hazardous voltages directly.
The safe isolation from the supply must be checked using a two-pole voltage detector.
Attention!
Even after switching off, dangerous temperatures can still occur in and on the device.
Attention!
Automatically restart after a power failure or mains disconnection!
2.7 Modifications / interventions in the device
Attention!
For reasons of safety, no unauthorized interventions or modifications may be made on the device. All
planned modifications must be authorized by the manufacturer in writing.
Use only genuine spare parts / genuine wearing parts / genuine accessories from ZIEHL-ABEGG.Th-
ese parts were specifically designed for the device. There is no guarantee that parts from non-original
sources are designed and manufactured in correspondence with load and safety requirements.
Parts and optional equipment not supplied by ZIEHL-ABEGG are not approved by ZIEHL-ABEGG for
use.
2.8 Operator’s obligation of diligence
•The contractor or owner must also ensure that the electric systems and equipment are operated
and maintained in accordance with electro-technical regulations.
•The owner is obliged to ensure that the device is operated in perfect working order only.
•The device may only be used as intended.
•You must periodically examine the safety equipment for their properly functioning condition.
•The assembly instructions and/or operating instructions are always readily available at the
location where the device is being used, are complete and are in legible condition.
•These persons are regularly instructed in all applicable questions regarding occupational safety
and environmental protection and are knowledgeable regarding the assembly instructions
and/or operating instructions and, especially, are familiar with the safety instructions contained
therein.
•All safety and warning notices attached to the device are never removed and remain legible.
2.9 Employment of external personnel
Maintenance and service work are frequently carried out by external employees who often do not
recognize the specific situations and the thus resulting dangers.These persons must be comprehen-
sively informed about the hazards in their area of activity.
You must monitor their working methods in order to intervene in good time if necessary.
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Safety instructions
L-BAL-E016-GB 1925 Index 007 Part.-No.
6/32

3 Product overview
3.1 Operational area
The controller described is used for continuous speed adjustment on variable voltage 1~ motors used
to drive ventilators or pumps.
3.2 Maintenance
The device must be checked for soiling and, if necessary, cleaned in periodic intervals.
3.3 Transport
•The device is packed ex factory to suit the transport method previously agreed.
•Always use the original packaging materials when transporting the device.
•Avoid shocks and impacts to the device during the transport.
•During manual handling the human lifting and carrying restrictions must be observed and
adhered to.
3.4 Storage
•The device must be stored in its original packaging in a dry and weather-proof room.
•Avoid exposure to extreme heat and cold.
•Avoid over-long storage periods (we recommend a maximum of one year).
3.5 Disposal / recycling
Disposal must be carried out professionally and in an environmentally friendly way in accordance with
the respective national legal stipulations.
"Separate the materials by type and in an environmentally friendly way.
"If necessary, commission a specialist company with the waste disposal.
4 Mounting
4.1 General notes
Attention!
The following points must be complied with during the mechanical installation to avoid causing a defect
in the device due to assembly errors or environmental influences:
•Before installation remove the device from the packing and check for any possible shipping
damage! Start-up is not allowed in the case of transport damage!
•At a weight greater than 25 kg for men / 10 kg for women, the device should be lifted out by two
persons (according to REFA). The values may differ from country to country.
•Wear safety shoes and gloves for handling!
•Assemble the device on a clean and stable base. Do not distort during assembly! Use the
appropriate mounting devices for proper installation of the unit!
•Do not mount equipment on vibrating base!
•When mounted onto lightweight walls, there must be no impermissibly high vibrations or shock
loads. Any banging shut of doors that are integrated into these lightweight walls, can result in
extremely high shock loads. Therefore, we advise you to decouple the devices from the wall.
•Do not allow drilling chips, screws and other foreign bodies to reach the device interior!
•The device should be installed in a location where it will not be disturbed, but at the same time
can be easily accessed!
•Depending on the housing model use supplied stoppers for cable inlets, cut off necessary cable
inlets respectively to the cable diameter. Or alternative use cable inlet for cable glands. Any
cable ducts openings not used must be sealed!
•Care must be taken to avoid direct radiation from the sun!
•The device is designed for vertical installation (bottom cable inlet). A horizontal or reclined
installation is only permissible after technical release of the manufacturer!
•Be sure to observe proper heat dissipation (see Technical data, heat dissipation).
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Product overview
L-BAL-E016-GB 1925 Index 007 Part.-No.
7/32

4.2 Minimum space requirement
In order to ensure sufficient ventilation of the device, clearance on all sides of at least 50 mm has to
be maintained to the housing walls, switch cabinet doors, wiring ducts, etc. The same clearance
applies to the installation of several devices next to each other.
When installing several devices on top of each other, the danger of reciprocal heating exists. This
layout is only then permissible when the air suctioned from the upper unit does not become warmer
than the permissible ambient temperature (see Technical data). I.e., a correspondingly larger clear-
ance or thermal shielding is required.
4.3 Outdoor installation
Outdoor installation is possible up to -20 °C when the controller supply is not switched off. Installation
must be protected from the effects of weather as much as possible, including protection from direct
sunlight!
4.4 Installation location for agriculture
When using for animal keeping, do not install the device directly in the stable but in a separate room
with a lower pollutant load. This helps to avoid damages caused by pollutant gases (e.g. ammonia
fumes, hydrogen sulphide fumes).
4.5 Temperature influences during commissioning
Avoid condensation in the controller and functional faults attributable to condensation by storing the
controller at room temperature!
5 Electrical installation
5.1 Safety precautions
Danger due to electric current
•Work on electric components may only be carried out by trained electricians or by persons
instructed in electricity under the supervision of an electrician in accordance with electrical
engineering regulations.
•The 5 electrical safety rules must be observed!
•It is forbidden to carry out work on electrically live parts.
•Cover neighbouring electrical equipment during installation work.
•Other measures may be necessary to achieve safe electrical isolation.
•A second person must always be present when working on energized parts or lines who
disconnects in case of emergency.
•Electrical equipment must be checked regularly: Loose connections are to be re-tightened and
damaged lines or cables must be replaced immediately.
•Always keep switch cabinets and all electrical supply facilities locked. Access is only allowed for
authorized persons using a key or special tool.
•Operating the device with the housing cover removed is prohibited because energized, exposed
parts are present inside the device. Disregarding this regulation can lead to severe personal
injury.
•The required protective earth connection is established using screws between the housing parts
in metal terminal space covers and housing casings. Commissioning is only permissible after
these screws have been properly attached!
•The device owner is responsible for the EMC of the entire plant according to the locally
applicable standards.
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Electrical installation
L-BAL-E016-GB 1925 Index 007 Part.-No.
8/32

•Metal screwed-connections are not permitted in plastic housing parts because there is no
potential equalization.
•Never clean electrical equipment with water or similar liquids.
Information
The respective connections are represented in the enclosure of this Operating Instructions (see
connection diagram)!
5.2 EMC-compatible installation
5.2.1 Motor cable
The applicable standard for interference emissions is EN 61000-6-3. Compliance with this standard is
achieved through the use of an unscreened motor feed cable.
5.2.2 Control cables
Pay attention to sufficient distance from powerlines and motor wires to prevent interferences. The
control cable may not be longer than 30 m. Screened control cables must be used when the cable
length is longer than 20 m. When using a shielded cable connect the shielding to one side only, i.e.
only to the control unit with the protective ground (keep cable short and with as little inductance as
possible!).
5.2.3 Harmonics current for devices ≤ 16 A
According to EN 61000-3-2 these devices are to be classified as “professional” devices.
Connection to a low voltage supply (public networks) is allowed insofar as this has been clarified with
the respective energy supply company responsible.
Note: up to a maximum current of approx. 4 A, the limits are adhered to with no restrictions.
Exception for Germany: An energy provider follows the technical connection conditions of the
TAB2007, in which case the use of phase angle controlled devices up to a rating of 3.4 kVA per phase
is allowed.
5.3 Mains connection
The mains connection is made at the terminals: PE, L1 and N. In this regard, it is essential to ensure
that the mains voltage lies within the allowable tolerance specifications (see technical data and rating
plate affixed to the side).
Danger due to electric current
The mains voltage must comply with the DIN EN 50160 quality characteristics and the defined
standard voltages in IEC 60038!
5.4 Motor connection
The motor is connected at terminals U1 and U2. Several motors can be connected to the device.
Attention!
The maximum total control current (specified for electronic voltage regulation) for all motors may not
exceed the device’s rated current.
If the maximum control current for electronic voltage regulation is not known, a supplementary 20 % of
the rated motor current must be allowed for.
When controlling motors from other manufacturers, the controllability and the maximum current for
electronic voltage regulation should be requested from the manufacturer.
Information
•It is recommended that a separate motor protection unit be foreseen for each fan.
•For motors with thermistors “TB” e.g. type S-ET10.
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Electrical installation
L-BAL-E016-GB 1925 Index 007 Part.-No.
9/32

5.4.1 Running noise
When controlling ventilators using electronic voltage regulators, motor noise can occur (due to the
system), which can be troublesome (Phase cutting series “P...”).
On fast running ventilators with a high level of air noise, this noise is relatively low. On slow running
ventilators with a low level of air noise, this noise may be dominant in the lower speed range due to
the occurrence of resonance.
For systems where noise is critical, we recommend using our Fcontrol series frequency converters
with integrated sinusoidal filter.
5.5 Motor protection
The motor can be protected by connecting thermostats “TB”.
When multiple motors are connected, it is essential to ensure that thermostats “TB” are always
connected in series.
If a connected thermostat is tripped (break between the two terminals “TB”), the device is switched off
and is not switched back on.
Relais “K1” is de-energized, terminals “11” - “12” bridged. The signal lamp flashes in code
| 1 | (see
Diagnostics / faults).
Possibilities for re-starting after the drive has cooled down (terminals “TB” bridged) by:
•By switching the mains voltage off and then on again.
•Via a digital input for remote control (ON / OFF enable).
Attention!
•An outside voltage may never be connected to the terminals “TB”!
•If a bypass circuit is installed, or in the “100 %” position on devices with a main switch, the motor
protection inside the controller has no function. In this case, additional motor monitoring may be
required.
5.6 Signal or sensor connection (E1 Analog In 1)
The unit has one-analog input: terminals “E1” / “GND” (Analog In 1).
The connection is independent of the programmed operating mode and from the sensor signal
employed.
The internal jumpers must be placed in correct position depending on input signal. Factory setting 0 -
10 V.
•When connecting passive temperature sensors TF.. (KTY81-210) must be paid attention to no
polarity.
•When connecting active sensors attention must be paid to correct polarity, a 24 V DC power
supply is integrated.
• For sensors in two-wire-technology (4 - 20 mA signal), the connection is made on the “+24 V”
and “E1” (“GND” terminal is omitted).
Over DIP 4 an inverting of the input is possible for mode 1.01 speed controller.
•DIP 4
| OFF | (factory setting) for signals: 0 - 10 V, 2 - 10 V, 0 - 20 mA, 4 - 20 mA
•DIP 4
| ON | for signals: 10 - 0 V, 10 - 2 V, 20 - 0 mA, 20 - 4 mA
Attention!
Never apply line voltage to analog inputs!
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Electrical installation
L-BAL-E016-GB 1925 Index 007 Part.-No.
10/32

5.7 Output voltage 0 - 10 V (A1 Analog Out 1)
Connection to terminals “A1” - “GND” “Analog Out 1” (I
max
10 mA).
It is not permissible to connect outputs of several devices to each other!
For mode speed controller 1.01 function of signal output A1 (Analog Out 1) can be determined
by DIP 8.
DIP 8
| OFF | Constant voltage + 10 V for external potentiometer (factory setting)
DIP 8
| ON |
0 - 10 V modulation 0 - 100 %
•Proportional the internal control of modulation with consideration “n-min” and “n-max”
setting.
•For enable “OFF” it goes not back to“0 V”.
•For motor fault the output signal remains for a slave controller (“Master-Slave”
combination).
For mode as P-Controller or PI-Controller 2.01 , 3.01 , 4.01 the function is firmly adjusted.
0 - 10 V
modulation 0 - 100 %
•Proportional the internal control of modulation with consideration “n-min” and “n-max”
setting.
•For enable “OFF” it goes back to “0 V”.
•For motor fault the output signal remains for a slave controller (“Master-Slave”
combination).
Information
For operation as P-Controller or PI-Controller function “constant voltage” cannot be selected!
For operation as P-Controller or PI-Controller function for
| D1 | can be selected with DIP 8!
5.8 Voltage supply for external devices (+24V, GND)
A voltage supply is integrated for external devices e.g. a sensor (max. current load see technical
data).
In case of overload or short circuit (24 V – GND), the external power supply is shut down (multi-fuse).
The device performs a “Reset” and continues operation.
•It is not permissible to connect voltage outputs of several devices to each other!
•It is not permissible to connect voltage outputs in the device to each other!
5.9 Digital input (Digital In 1 D1)
Activation via floating contacts, a low voltage of approx. 24 V DC is connected.
Attention!
No disconnection (isolation) when turned off, in accordance with VBG4 §6)!
Never apply line voltage to the digital input!
It is not permissible to connect inputs of several devices to each other!
5.9.1 Enable, device ON / OFF
Electronic disconnection and Reset after motor fault via floating contact at terminals “D1” -
“D1”
•Device “ON” for closed contact.
•Device “OFF” with opened contact.
•Relais “K1” remains energized, terminals 12 - 14 bridged. The signal lamp flashes in code
| 1 |
(see Diagnostics / faults)
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Electrical installation
L-BAL-E016-GB 1925 Index 007 Part.-No.
11/32

5.9.2 Reverse action of control function (only for P-Controller / PI-Controller)
For operation as P-Controller or PI-Controller 2.01 , 3.01 , 4.01 . Digital input can used instead for
enable, alternative for reverse of control function (DIP 8
| ON | ).
For the effect of the regulation there are two functions:
•“Val > Set n+”
increasing modulation for increasing actual value over setpoint.
•“Val < Set n+”
increasing modulation for decreasing actual value below setpoint.
When terminals “D1” - “D1” bridged, the device works with the opposite function than the one set with
DIP 4!
5.10 Relay outputs (K1)
An external fault indicator is available over the potential-free contacts of the built-in relay (max. contact
rating Technical data and connection diagram).
For operation the relay is energized, terminals “12” and “14” are bridged. For fault the relay is de-
energized, terminals “11” and “12” are bridged (
Diagnostics / faults).
•Fault indicated for: line fault, blown internal semiconductor fuse, broken controller-internal
voltage supply, overheating by the motor (thermostats “TB” connected).
•By sensor failure (only in P-Control or PI-Control operation 2.01 , 3.01 , 4.01 ) message only via
flash code of signal lamp (code
| 3 | ), the relay remains energized.
•When switching off via enable (D1 Digital In 1), the relay remains energized.
5.11 Potential at control voltage connections
The connections for the control voltage (< 30 V) relate to the common GND potential (exception: relay
contacts are potential-free). There is a potential isolation between the connections for the control
voltage and the PE conductor. It must be ensured that the maximum external voltage at the con-
nections for the control voltage cannot exceed 30 V (between the “GND” and “PE” conductor
terminals). A connection to the PE conductor potential can be made if required; fit a bridge between
the “GND” terminal and the “PE” connection (terminal for shield).
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Electrical installation
L-BAL-E016-GB 1925 Index 007 Part.-No.
12/32

6 Operating and display elements
6.1 Main switch and potentiometer with integrated light signal
1Main switch
Position Function
100 % Ventilators are operated directly from the mains with no control.
The fuse in the device is bypassed! Motor protection has no function
0Controller off
Auto
Function dependently on selected mode of operation
For Speed controller 1.01 adjusting via external signal (DIP 2
| OFF | factory setting) or internal
potentiometer “set” (DIP 2
| ON | ).
Setting range: Output voltage 0 - 100 %.
For P-Controller, 2.01 , 3.01 and PI-Controller, 4.01
Automatic speed control depending on actual value measured and configured set value.
Manual setting of output voltage by potentiometer 2
2Potentiometer outside 0...100 %
For main switch position “Auto”
function depending on internal switch “DIP 2” and selected mode
•For Speed controller 1.01 always without function
•For the P controller, 2.01 , 3.01 and PI controller, 4.01 the “DIP 2” switch can be used to select whether
the set value setting can be made easily using the outer potentiometer or using the internal potentiometer “set”.
The internal potentiometer is set to active
ex-factory (DIP 2
| OFF | ) i.e. the set value setting is protected against unauthorized adjustments.
–For temperature control 2.01 with passive sensors TF.. (KTY).
setting range: 0 - 100 %
-26...76 °C (measuring range of controller).
–For control with active sensors 3.01 , 4.01 (0 - 10 V, 4 - 20 mA).
Setting range: 0 - 100 %
measuring range of sensor.
For main switch position “Hand”
•Setting of output voltage 0 -100 %. Independently from input signal and selected mode.
3Potentiometer with integrated light signal
Indicate the operating conditions over flashing code.
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Operating and display elements
L-BAL-E016-GB 1925 Index 007 Part.-No.
13/32

6.2 Internal Setting
Attention!
The controller housing cover may only be removed when the power line has been switched off!
It is generally forbidden to carry out work on electrical live parts. Protection class of the device when
open is IP 00! It is possible to touch hazardous voltages directly.
18.07.2011
v_pxet_q_intern_bed.VSD
%
n-max
0100
%
set
0100
%
n-min
0100
V
°C
mA
E1
ON
OFF
10987654321
DIP S1
%
Pband
530
Potentiometer
set
For main switch position “Auto” function depending on internal switch DIP 2 and selected mode (for
main switch position “Hand” without function).
•For Speed controller 1.01 and DIP 2
| OFF | (factory setting) without function
•For Speed controller 1.01 and DIP 2
| ON | setting of output voltage 0 - 100 %
At P controller 2.01 3.01 and PI controller 4.01 can be selected with DIP 2 whether the setpoint
adjustment is made via this internal potentiometer or via the external potentiometer (the internal
potentiometer is active at the factory (DIP 2
| OFF | ).
•For temperature control 2.01 with passive sensors TF.. (KTY).
setting range: 0 - 100 %
-26...76 °C (measuring range of controller).
•For control with active sensors 3.01 , 4.01 (0 - 10 V, 4 - 20 mA).
Setting range: 0 - 100 %
measuring range of sensor.
Potentiometer
Pband
Function dependently on selected mode of operation
•For Speed controller 1.01 : without function
•P-controller 2.01 , 3.01
–For temperature control with passive sensors TF.. (KTY).
Setting range: 5 - 30 %
5.1 - 30.6 K.
–For control with active sensors (0 - 10 V, 4 - 20 mA).
Setting range: 5 - 30 %
5 - 30 % measuring range of sensor.
•PI-Controllerr 4.01
–For control with active sensors (0 - 10 V, 4 - 20 mA).
Setting range: 5 - 30 %
5 - 100 % measuring range of sensor.
Potentiometer
n-min
Minimal output voltage (basic speed)
Setting range: 0 - 100 % (“n-min” takes priority if over “n-max”)
Potentiometer
n-max
Maximal output voltage (speed limiter)
Setting range: 100 % - “n-min”
Jumper
E1 Basic setting for kind of signal at analog input “E1 Analog In 1”
Dipswitch
S1 Basic setting for device function
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Operating and display elements
L-BAL-E016-GB 1925 Index 007 Part.-No.
14/32

7 Base setup
7.1 Programming of the desired function (Speed controller / P-Controller, PI-Controller)
•It is possible to use the device as a Speed controller or as a P-controller, PI-Controller. Selection
of the function must first be made by setting the internal jumper “E1” and dipswitch “S1”.
•Factory setting of internal jumper “E1” in position for 0 - 10 V input signal. When using
other signals bring the jumper in correct position.
•Factory setting of all dipswitches is
| OFF | position for operation as Speed controller
1.01 with external setting signal. In the following the fundamental dipswitch positions for
further modes of operation are represented. Depending upon desired function further adjust-
ments are necessary (
function dipswitches).
Attention!
Setting of jumper and switches not under voltage! Observe the safety notices!
Changed functions become active partly only after renewed switching on the mains voltage!
E1 Analog In (factory setting 0 - 10 V)
13.03.2012
v_jumper_e1_dip_s1_mode.vsd
AE1 GND
0 - 10 V
10 k
E1 GND
TF..
TF.. (KTY)
31
BN GN
24V E1
MBG..
4 - 20 mA
(0 - 20 mA)
4 - 20 mA
24V E1 GND
YE
DSG..
WHBN
0 -10 V
24V E1 GND
3
MAL1/10
21
0 -10 V
E1 E1
0 - 10 V
E1
0 - 10 V
E1
1.01 2.01 3.01 4.01
ON
OFF
10987654321
S1
ON
OFF
10987654321
S1
ON
OFF
10987654321
S1
ON
OFF
10987654321
S1
7.2 Select operation mode
Simple installation is possible through the use of modes of operation.
Mode Signal or Sensor
(input) Function
1.01 Signal 0 - 10 V Speed controller, two step operation (factory setting)
2.01 Sensor TF.. (E1) Temperature control airconditioning and refrigeration
3.01 Sensor MBG.. (E1) Pressure control condensers (refrigeration)
4.01 Sensor DSG.. (E1) Pressure control for ventilation systems
Sensor MAL.. (E1) Air velocity control e.g. clean room
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Base setup
L-BAL-E016-GB 1925 Index 007 Part.-No.
15/32

7.3 Function of dipswitches for operation as Speed controller 1.01 (DIP 1 | OFF | )
For operation as a speed controller (main switch Auto), the output voltage is set manually by
adjusting the built-in potentiometer, by an external potentiometer or external signal.
The desired function is determined with dipswitch S1.
Position factory setting for all dipswitches
| OFF |
DIP Function OFF ON
1
Selection:
Speed controller / P-Controller,
PI-Controller
RPM controller P-Controller, PI-controller
2Signal source of control
Setting of output voltage by external signal
to “E1”
(“Potentiometer outside” and “potentiome-
ter inside ” “set” without function)
Setting of output voltage by “potentiometer
inside” “set”
(“Potentiometer outside” without function)
3Type of Signal 0 - 10 V, 0 - 20 mA 2 - 10 V, 4 - 20 mA
4Inverting signal input 0 - 10 V, 2 - 10 V, 0 - 20 mA, 4 - 20 mA 10 - 0 V, 10 - 2 V, 20 - 0 mA, 20 - 4 mA
5Minimum speed cut off OFF ON
6Hardstart function OFF ON
7no function - -
8Function signal output “Analog
Out 1”
Constant voltage “+ 10 V” for external
potentiometer 0 - 10 V
modulation 0 - 100 %
9no function - -
10 no function - -
7.4 Function of dipswitches for operation as P-Controller, PI-Controller, 2.01 , 3.01 , 4.01
(DIP 1 | ON | )
For operation as a P-controller, PI-Controller (main switch Auto) the actual value measured by the
sensor is compared with the nominal value that has been set. The output voltage and hence the
rotational speed of the connected motor automatically change as a function of the parameter settings.
The desired function is determined with dipswitch S1.
Position factory setting for all dipswitches
| OFF |
DIP Function OFF ON
1
Selection:
Speed controller / P-Controller,
PI-Controller
RPM controller P-Controller, PI-controller
2Function “potentiometer out-
side”
Setpoint setting via “potentiometer inside”
“set”.
“Potentiometer outside” without function.
Setpoint setting via “ potentiometer out-
side”
“Potentiometer inside” “set” without func-
tion.
3Type of Signal 0 - 10 V, 0 - 20 mA
TF.. (KTY) 2 - 10 V, 4 - 20 mA
4Control function (e.g. “Cooling” /
“Heating”
increasing modulation for increasing actual
value
increasing modulation for decreasing ac-
tual value
5Minimum speed cut off OFF ON
6Hardstart function OFF ON
7Controller function
| P |
Applications:
Temperature control airconditioning and
refrigeration “sensor TF..”
Pressure control condensers (refrigera-
tion) “sensor MBG..”
| PI |
Applications:
Volume control (constant) for ventilation
systems “Sensor DSG..”
Air velocity control e.g. clean room “Sensor
MAL..”
8Function digital input “Digital In
1”
Enable
Device ON / OFF
Switch over control function:
- Val > Set n+ (Cooling)
- Val < Set n+ (Heating)
(reverse function DIP 4)
9no function - -
10 no function - -
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Base setup
L-BAL-E016-GB 1925 Index 007 Part.-No.
16/32

7.5 Minimum speed cut off DIP 5
7.5.1 For mode Speed controller 1.01
If no “n-min” is adjusted,output voltage goes continuously with reduction of the regulating variable
down to “0” (cutoff below approx. 2 % regulating variable).
Without minimum speed cut OFF (DIP 5
| OFF | factory setting)
•If minimal speed “n-min” is adjusted (e.g. 20%), then no disconnection of the fan takes place.
I.e. always a minimum ventilation is ensured (fan does not go under setting “n-min”).
With minimum speed cut off (DIP 5
| ON | )
•Cutoff below approx. 2 % regulating variable from sestting “n-min” to “0”.
•Switch on again for a regulating variable above 5 % (to setting “n-min”).
Functional diagram see setting for operation as Speed controller
7.5.2 For operation as P-Controller, PI-Controller 2.01 , 3.01 , 4.01
This function is primarily significant for installation of the device as a pure P-Controller ( 2.01 , 3.01 ).
Without minimum speed cut OFF (DIP 5
| OFF |
factory setting)
•If no “n-min” is adjusted, the fan stops with
reaching the desired value.
•If “n-min” is adjusted (e.g. 20 %), then no
disconnection of the fan takes place. I.e. always a
minimum ventilation is ensured (fan does not go
under setting “n-min”).
With minimum speed cut off (DIP 5
| ON | )
•When the setpoint is reached, the modulation is
reduced to “0 %”, or to the set value if “n-min” is
specified.
•For actual value setpoint disconnection takes
place from “n-min” to “0”. Hysteresis (ON / OFF)
approx. 2.5 % of 100 % set value.
nM
50 %
100 %
I
Min.
Min. 35 % Max. = 100 %
20 °C
S
7 K
R
27 °C
-2.0 K
10.05.2007
v_min_luft_abschalt.vsd
Minimum speed cut off (idealized principle diagram)
nM Motor speed
S Setpoint
R Pband
I Actual value
7.6 Hardstart function DIP 6
Special function for motorstart with maximum output voltage.
DIP 6
| OFF |
“Hardstart” function OFF (factory setting).
After switching the mains voltage on the output voltage rises during the firmly programmed
run-up time to the given value.
DIP 6
| ON |
“Hardstart” function ON.
For a safe starting of the connected fans the function “Hard start” can be activated.
After switching on (line voltage or enable via digital input “D1”) the controller generates for
approx. 10 seconds max. voltage “100 %” ignoring any control or sensor signal.
Afterwards the output voltage adjusts itself to the given or over the control amplifier calculated
value.
For operation as controller(from mode 2.01 ) the “Hard start” function works also by switching
over the control function (“Heating” / “Cooling”).
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Base setup
L-BAL-E016-GB 1925 Index 007 Part.-No.
17/32

8 Start-up
8.1 Prerequisites for commissioning
Attention!
1. You must mount and connect the device in accordance with the operating instructions.
2. Double check that all connections are correct.
3. The mains voltage must match the information on the rating plate.
4. The rated current on the rating plate will not be exceeded.
5. Make sure that no persons or objects are in the hazardous area.
9 Setting for operation
9.1 Speed controller 1.01
9.1.1 Setting for operation as Speed controller
Signal to:
E1
E1 GND
14.02.2008
v_signal_e1.vsd
E1
Setting via external signal or external potentiometer (DIP 2
| OFF | factory
setting)
Setting range: Output voltage from approx. 0 - 100 % of connected line voltage or in
range of settings “n-min” up to “n-max”.
(Potentiometer set without function)
%
set
0100
18.07.2011
v_set_pxet.VSD
set
For setting via internal potentiometer (DIP 2
| ON | )
Setting range: Output voltage from approx. 0 - 100 % of connected line voltage or in
range of settings “n-min” up to “n-max”.
18.07.2011
v_nmin_pxet.VSD
%
n-min
0100
n-min
Minimum output voltage (basic speed)
Setting range: 0 - 100 % (“n-min” takes priority if over “n-max”).
18.07.2011
v_nmax_pxet.VSD
%
n-max
0100
n-max
Maximal output voltage (speed limiter)
Setting range: 100 % - “n-min”.
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Start-up
L-BAL-E016-GB 1925 Index 007 Part.-No.
18/32

9.1.2 Diagram: setting signal and speed
nM
50 %
100 %
0 1 2 3 4 5 6 7 8 9 10
10 9 8 7 6 5 4 3 2 1 0
0 2 4 6 8 10 12 14 16 18 20
20 18 16 14 12 10 8 6 4 2 0
4 5,6 7,2 8,8 10,4 12 13,6 15,2 16,8 18,4 20
20 18,4 16,8 15,2 13,6 12 10,4 8,8 7,2 5,6 4
0 – 10 V
10 – 0 V
0 – 20 mA
20 – 0 mA
4 – 20 mA
20 – 4 mA
Min.
Min. 0 % Max. = 100 %
Min. 35 % Max. = 85 %
05.02.2008
v_nmotor_101_miluab.vsd
Si
Idealized principle diagram
nM Motor speed
Si Signal
9.1.3 Operation with two variable output voltages (two steps)
DIP2
| OFF | for setting via external signall.
Switchover between two steps via external potential-free contact possible.
•Step 1 (low speed). When there is no input signal connected to the input terminal “E1”, then the
unit supplies the output voltage set by “n-min”.
•Step 2 (high speed). When the terminal “A1” (+10 V) is connected with the input terminal “E1”
then the units supplies the output voltage set by “n-max”.
n-min
nM
100 %
1
t
n-max
12 05.02.2008
v_diagr_2stufen.VSD
"A1" (+10 V)
"E1"
nMotor
= "n-max"
nMotor
= "n-min"
1
2
05.02.2008
v_schalter_2stufen.VSD
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Setting for operation
L-BAL-E016-GB 1925 Index 007 Part.-No.
19/32

9.2 Temperaturre control (P-Controller) 2.01
9.2.1 Setting for operation as Temperature controller
%
set
0100
18.07.2011
v_set_pxet.VSD
potentiometer inside
(DIP 2 OFF)
or
26.05.2008
v_pxet_q_aussen
_pot.VSD
potentiometer outside
(DIP 2 ON)
set
Setpoint setting alternatively by “potentiometer inside” (DIP 2
| OFF | ) or “potenti-
ometer outside” (DIP 2
| ON | )
For control with active sensors (0 - 10 V, 4 - 20 mA)
Setting range: 0 - 100 %
measuring range of sensor
For Temperature control with passive sensors TF.. (KTY)
Setting range: 0 - 100 %
-26...76 °C (measuring range of controller)
The enclosed scale for type TF.. temperature sensors can be attached
above the potentiometer.
28.05.2008
v_pxet_q_skala_temp.VSD
set [% ] 0 10 20 30 40 50 60 70 80 90 100
[C°] -26.0 -15.8 -5.6 4.6 14.8 25.0 35.2 45.4 55.6 65.8 76.0
Scale 0 - 100 % -26...76 °C for Temperature control with passive sensors TF.. (KTY)
set
[%] 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
[° C] -26.0 -20.9 -15.8 -10.7 -5.6 -0.5 4.6 9.7 14.8 19.9 25.0 30.1 35.2 40.3 45.4 50.5 55.6 60.7 65.8 70.9 76.0
19.07.2011
v_pband_pxet.VSD
%
Pband
530
Pband
Pband
Narrow control range Short control times
Wide control range Longer control times and more stable control
For control with active sensors (0 - 10 V, 4 - 20 mA)
Setting range: 5 - 30 % 5 - 30 % measuring range of sensor
For Temperature control with passive sensors TF.. (KTY)
Setting range: 5 - 30 %
5.1 - 30.6 K
18.07.2011
v_nmin_pxet.VSD
%
n-min
0100
n-min
Minimum output voltage (basic speed)
Setting range: 0 - 100 % (“n-min” takes priority if over “n-max”)
18.07.2011
v_nmax_pxet.VSD
%
n-max
0100
n-max
Maximal output voltage (speed limiter)
Setting range: 100 % - “n-min”
Operating Instructions Acontrol – model series PXET6Q / PXET10Q Setting for operation
L-BAL-E016-GB 1925 Index 007 Part.-No.
20/32