Zip ChillTap 804721 User manual

Zip ChillTap Sparkling
®
Residential - Filtered chilled still and chilled sparkling water
Affix Model Number Label Here
804721
804721 09.16 v1.0

Page 2 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
Pre-Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . 3
Read These Warnings First . . . . . . . . . . . . . . . . . . . . 4
Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 4
Section 1 - Tap Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 - Installing the Tap . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 2 - Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 - Ventilation (all models) . . . . . . . . . . . . . . . . . . . . 6
2.2 - Extra ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Section 3 - CO2Cylinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 - Secure the cylinder mounting . . . . . . . . . . . . . . . 9
3.2 - Connect the regulator . . . . . . . . . . . . . . . . . . . . . 9
3.3 - Connect the gas hose . . . . . . . . . . . . . . . . . . . . . 9
3.4 - Test for gas leaks . . . . . . . . . . . . . . . . . . . . . . . . 9
Section 4 - Undersink unit installation . . . . . . . . . . . . . . . . . . . 10
John Guest (J.G.) fittings . . . . . . . . . . . . . . . . . . 10
4.1 - Chiller Installation . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 - Hose and Tube connections . . . . . . . . . . . . . . . . 11
4.3 - Mains Connection . . . . . . . . . . . . . . . . . . . . . . . . 12
4.4 - Chilled Still Connection . . . . . . . . . . . . . . . . . . . . 12
4.5 - Chilled Sparkling /
Carbonation Valve Connection . . . . . . . . . . . . . . . . . . 12
Section 5 - Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 - Test and Commission . . . . . . . . . . . . . . . . . . . . . 14
5.2 - Adjusting the flow rate . . . . . . . . . . . . . . . . . . . . . 15
Section 6 - Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1 - Water Filter Replacement . . . . . . . . . . . . . . . . . . 16
6.2 - Air Filter Change . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.3 - Gas Bottle Replacement . . . . . . . . . . . . . . . . . . . 17
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
End of Life Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Contact Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Contents

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 3 of 20
Pre-Installation Notes
A. Read the instructions.
B. Note: All fittings are supplied with the appliance kit except an isolation valve.
C. Check the water quality to determine if extra filtration will be required.
D. Check the appliance rating plate and ensure correct power is available for the
appliance.
E. Check the underbench cupboard supporting the appliance is adequate for
the total weight of the appliance.
F. Ensure a potable water supply connection with isolating valve inside the cupboard
is within reach of the braided hoses and positioned so that the connection point
and the stop cock will not be obstructed when the undersink units are installed.
Note:
All plumbing must comply with AS/NZS 3500.4.1 & AS/NZS 3500.4.2
All electrical must comply with AS/NZS 3000 wiring rules
All refrigeration must comply with AS/NZS 3350.2.24
Precautions
The plumbing installation must be done in accordance with local Water Authority
regulations and these Installation Instructions.
As the installer, it is your responsibility to supply (if necessary) and install all valves
as required by local regulations and relevant standards.

Page 4 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
1. Please read all Precautions, Installation Requirements, Installation Instructions before installing any Zip ChillTap.
2. Never attempt to install any Zip ChillTap without reading all of the applicable instructions.
3. All electrical connections must comply with current wiring rules.
4. This appliance is not designed for use by young children or infirm people without supervision.
5. Young children should be prevented from having access to ensure they are not able to use or play with the chiller.
6. This appliance must be earthed.
7. If the power supply cord is damaged it must be replaced by a Zip Service Provider or a qualified electrician.
8. The power cord and general power outlet must be in a safe and accessible position after installation.
9. Do not remove the cover of the appliance under any circumstances without first isolating the appliance from the power
supply.
10. This unit is designed for indoor use and must not be installed outdoors or exposed to the elements of nature.
11. This unit must not be positioned in an area that may be cleaned by a water jet.
12. This unit must not be cleaned by a water jet.
13. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. For products sold in Europe, this appliance can be used by children
aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
14. This appliance is intended to be used in household and similar applications such as
Staff kitchen areas in shops, offices and other working environments;
Farm houses and by clients in hotels, motels and other residential type environments;
Bed and breakfast type environments;
Catering and similar non-retail applications.
15. The appliance has to be placed in a upright position.
Product Specifications
Model Power Rating
(kW) Refrigerant Height mm Depth mm (including fittings) Width mm Weight empty kg’s Weight full kg’s
CS 0.3 134A(100g) 335 442 280 25 26
Read These Warnings First
• Power supply 220-240VAC 50Hz for connection via a 10amp G.P.O.
• Operating temperatures 5ºC - 35ºC.
• External water pressure 250kPa - 700kPa (2.5 bar -7 bar)
• Internal Pressure Limiting Valve: 500kPa
Note:For best results we recommend a minimum static mains water pressure of 250kPa (2.5 bar).
Frost Protection
If this appliance is located where the ambient air
temperature could fall below
5ºC when the heater is not
in use, do not turn off the appliiance electrically. This safe-
guard does not offer the same protection to the connecting
pipework and fittings.
Installation Requirements

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 5 of 20
Section 1
Tap Installation
Installing the Tap
Position and install the carafe filler at the back of the sink or on the Font,
where there is a minimum 52mm wide flat area within the draining area
of the sink.
Ensure the distance between the tap and the command centre does not
exceed the length of the supplied tubing.
NOTE: Hoses are maximum 1000mm in length.
Make sure the selected position allows the carafe filler spout to overhang
the sink bowl.
Make sure the selected position allows the carafe filler spout to overhang
the sink bowl.
Use a 25mm sheet metal punch to create a neat hole without burrs.
Remove the large nut with the stainless steel and rubber washers from
the base of the carafe filler, leaving the rubber-sealing ring (O-ring) in
place.
Fit the carafe filler and seal to the sink, oriented so both the operating
levers are easily accessible.
Slide first, the rubber washer and then the brass washer, followed by the
nut, over the tubes from under the sink, and tighten the nut to secure the
carafe filler firmly into place.
NOTE: The Clear tube must be trimmed to length and blocked with
the JG fitting supplied.
O-RING
LOWER
RUBBER
WASHER
WASHER NUT
BLUE tube
to
Still Outlet
WHITE tube
to
Sparkling Outlet
CLEAR tube
blocked with
JG fitting
Warning - Do not reuse the old hose-sets. The unit
shall be installed with the new hose-sets supplied.
Special Tools
In addition to common tools, the following will be required:
• 25mm diameter sheet metal hole punch for sink tops. (Not supplied)
• 25mm diameter hole saw for timber bench tops. (Not supplied)

Page 6 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
2.1- Ventilation
Proper air circulation must be provided for all Chilled models. The system will operate correctly only if the recommended air
gaps are achieved during Installation. The minimum requirement is for a 50mm air gap either side and 300mm above of the
undersink unit.
It is important that the 4mm door buffers (For all installations ) are fitted to the inside edge of the cupboard door to allow
sufficient air circulation inside the cupboard. (See the diagram below).
• When installing air flow ducts, the following tools will be required:
• Jigsaw and 12mm Drill
• Keyhole or Wall Board saw.
Section 2
Ventilation
50 min. 50 min.
200 min.
382
280
333
Ø 105
Clearance
Envelope
Vent pipe
(Blocked o)
Mains Cold water
isolation valve
240 - 230V,
50Hz GPO
CO
2
cylinder with
xed 300kPa reguator
Inlet Vent
Carbonation
adjustable
ow valve
435
Clearance
Envelope
4min,
Bufer Pad
Clear Gap

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 7 of 20
Ventilation
Air inlet vent position
Airflow through the cupboard
B
D
g
p
Cool air IN
Warm air
OUT
Door outlet vent
1. Drill four pilot holes 12mm
dia.
2. Finish the cutout using a
jig saw and keyhole or Wall
Board saw
If the air flow, using the silicon door buffers, is insufficient, it will be necessary to fit a standard ChillTap vent kit, which ensures heat
dissipation through natural convection via installed vents.
For high use applications, where the cupboard space temperature is near 35°C, or higher, the inlet vent (See Item B below) and
silicon buffers, need to be fitted.
If the airflow is still insufficient to maintain normal operating temperatures then the inlet vent and door outlet vent (See item D
below) will need to be fitted.
Note: The vent kit has to be installed in a way that allows air to be drawn in from the bottom of the cupboard and expelled
through the top of the cupboard. Therefore placement of the outlet vent should be towards the top of the door or on the side of the
cupboard.
2.2- The following instructions are critical if there is insufficient cupboard air
circulation.
Cutout details

Page 8 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
Typical Cut out procedure for
B
Ventilation
Cutout details
Air inlet vent
1. Mark out and cut the air inlet and door outlet holes as shown
2. Ensure the air inlet vent and air outlet vent are positioned at opposite ends of the same
cupboard space.
3. Fit the inlet vent, as shown and secure with 5 screws
4. If required, fit the outlet vent, as shown in the hottest part (top) of the cupboard and
secure with 4 screws
BD

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 9 of 20
Section 3
CO2Cylinder
WARNING:
This cylinder must be installed in an open plan area or in an enclosed room,
with a volume no less than 20m3. If more than 1 gas cylinder containing CO2is
present within the same location, the recommended ventilated area should be in
proportion to the number of gas cylinders stored in that location.
A ventilated area is a non-enclosed area which could include the kitchen, living
room etc.
See gas bottle and MSDS sheet for a complete list of warnings.
(See: www.zipindustries.com)
3.1 Secure the cylinder mounting:
Secure the gas bottle supplied to a suitable wall, within 1 metre of the unit,
in an upright position. This is done by screwing the metal plate holding the
hook-and-loop strap to a cupboard wall, 200mm above the floor or base of the
cupboard. Make sure the gas bottle can stand before securing to the wall.
Due to regulatory requirements the gas bottle must be stored
securely and in an upright position.
3.2Connect the regulator:
Make sure the regulator knob is turned fully clockwise to the end-stop before
fitting see fig.1. Fit the regulator to the gas bottle. Be aware that some CO2may
be discharged from the connection to the regulator as the bottle and the regulator
are be assembled together. Any CO2released will be cold. Continue to screw on
the regulator to stop this leakage.
Note: The regulator comes pre-set fixed pressure at 300kPa.
3.3Connect the gas hose:
Connect the braided gas hose to the top of the undersink unit via the John Guest
fitting marked ‘CO2 IN’ Then connect the threaded end to the regulator, taking
care not to lose the plastic olive located inside the threaded nut. To turn the gas
ON, rotate the regulator knob anti-clockwise to the end-stop.
OPEN
CLOSED
Turn the knob fully clockwise
before fitting the regulator
Rotate the knob fully anti-
clockwise to turn the gas on.

Page 10 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
CO2Cylinder
3.4Test for gas leaks:
Using soapy water perform a leak test. Turn the gas OFF. Apply the soapy water
to the gas connections using a sponge or brush. Cover all of the gas joints with a
liberal amount of suds.
Turn ON the gas. Inspect the joint for leaks. If any bubbles appear and grow, there
is a gas leak at the connection. The joint will need to be resealed and tested again.
Clean away the soapy residue and tighten or refit the leaking connection. Make sure
the regulator is turned off when tightening or refitting the leaking connection.
Refit the gas bottle to the hook-and-loop strap and secure the bottle in an upright
position.
NOTE: Care must be taken when working with high pressure carbon dioxide.
IMPORTANT:
After replacing a bottle or after making a gas con-
nection, check for gas leaks between regulator and
bottle, and between regulator and braided hose.
Test for leaks at these two poitns

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 11 of 20
Section 4
Undersink Unit Installation
On / Off Switch
General instructions for
John Guest connections
NOTE:Ensure all John Guest
tube ends are cut clean and
square.
John Guest (JG) fittings
If caps are removed to allow lifting
handles to be installed during
installation of the unit, ensure they
are refitted when unit is in position.

Page 12 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
Undersink Unit Installation
Note:To avoid water leaks,
take care when bending rigid
plastic tubing. The tube must not
be kinked or crushed around a
bend, as the tube may containing
water under pressure. Therefore
be careful not to nick, scratch
or damage the tube during
installation.
4.1- Chiller Installation
Place the chiller unit into the cupboard with the proposed outlet tap position as close
as possible, to minimise the length of tubing exposed between the chiller unit and the
outlet tap. (The tubing length is limited to 1000mm)
Allow at least 50mm around the chiller unit to permit free airflow. Both the top and
the front of the chiller must remain accessible for servicing purposes.
4.2 - Hose and Tube connections:
NOTE: You must separately supply and install an isolation valve (not supplied) in
the water supply line before the connection to the product.
Connect the braided hose to the isolation valve. For best results we recommend a
minimum static pressure of 250kPa (2.5 bar).
4.3 Mains Connection (with chiller inlet):
Connect the braided hose from the isolation valve to the top of the undersink unit,
marked MAINS IN.
4.4 - Chilled Still Connection:
Remove the plug fitted into the connection marked “Still Outlet“ by first depressing
the collet and simultaneously pulling out the plug. Measure and trim the 1/4” blue
tube from the carafe tap to the JG fitting marked “Still Outlet” on the top rear of the
chiller unit. Before making connection, insulate the tube with the loose length of the
foam insulation, trim the insulation to the correct length, which is about 5-10mm
shorter than blue tube. Push the blue tube fully into the John Guest fitting marked
“Still Outlet”. Make sure all connections to John Guest fittings are pushed in past the
“O”ring to full depth.
4.5 - Chilled Sparkling / Carbonation Valve
Connection:
1. Remove the plug fitted into the connection marked “Sparkling Outlet“ by first
depressing the collet and simultaneously pulling out the plug. Fit the carbonation
valve to the sparkling outlet connection on top of the unit as shown in FIG.1.
2. Measure and trim the 1/4” white tube from the carafe tap.
3. Before making connection, insulate the tube with the loose length of the foam
insulation, trim the insulation to the correct length, which is about 5-10mm shorter
than white tube.
water flow
Carbonation
Valve
FIG.1

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 13 of 20
IMPORTANT: The Clear tube is non functional. However, it must be trimmed to length and blocked with the JG fitting supplied,
otherwise water will leak from it whenever the tap is operated.
Note:After dispensing sparkling water, a small amount will remain in the carafe filler. If the next drink is to be still water and you
do not wish any trace of sparkling water, the still water should be running for approximately 1 second before filling your glass or
bottle. The same is applicable if still water is dispensed prior to dispensing sparkling water.
Undersink Unit Installation
4. Connect the white tube to the carbonation valve as shown in FIG.2. Push the white tube fully into the in carbonation valve. Make
sure all connections are pushed in past the “O”ring to full depth.
5.Arranging tubes in the most direct route between tap outlet and unit.
The tap connection is now complete.
BLUE tube
to
Still Outlet
WHITE tube
to
Carbonation Valve
CLEAR tube
blocked with
JG fitting
FIG.2
Chilled Sparkling /
Carbonation Valve Connection

Page 14 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
Section 5
Commissioning
Chilled filtered water
(blue)
Sparkling filtered water
(white)
ROTATE
5.1- Test and Commission:
Do NOT turn power or water on to the unit. The carbonator must be purged
first with the CO2gas. Failure to do so will result in poor tasting water. Turn the
sparkling water lever on (white ringed lever) The CO2will start to run out of the
tap. Gas will purge or escape from the tap at this point. Let it run for approximately
5 seconds to completely fill the tank. Close the sparkling lever by rotating back to
upright.
Note: Should no CO2 gas be expelled, check if regulator valve is open.
Turn on the still water lever (blue ringed lever) then turn on the water supply to the
unit. First air, then water will flow from the tap. Allow the water to continue to flow
for about 7.5 litres, which is required to activate the filter. Once this has been done
turn off the still water lever.
Connect the unit to the mains power supply and turn ON. Confirm the ON/OFF
switch at the side of the undersink unit is on.
The compressor and fan will start, and the water pump will operate for
approximately 20 seconds to fill the carbonator vessel.
After approximately 5 minutes, the compressor and fan will stop as the chiller has
reached its normal operating temperature.
To achieve an optimal level of carbonation, it is beneficial to purge the carbonation
vessel again by isolating the water and electrical supply, and opening the sparkling
lever on the tap until gas is expelled for approximately 5 seconds. Close the tap
and turn on water and power. Wait 20 seconds and the sparkling water should be
ready for use.
Important: Optimal carbonation levels occur at low water temperatures.
Excessive flow rates of carbonated water will result in poor drink quality and
malfunction of system. It is recommended that the flow rate for carbonated water
should be approximately 1.2-1.6 litres/minute.
The lever on the right (Blue rings) is used for chilled still filtered water and the lever
on the left (White rings) is used for chilled sparkling filtered water.
Chilled water is obtained by rotating the lever on the right, to a horizontal position.
The water is chilled by a refrigeration unit fitted within the cabinet stand, under the
basin.
With the carafe tap, you can obtain chilled water within the rated capacity, for as
long as you leave the lever in the open (horizontal) position. When finished, return
the lever to the OFF (upright) position.
Sparkling water is obtained in the same way as the chilled water, by rotating the
lever on the left hand side of the carafe tap.
FIG.1
FIG.2

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 15 of 20
5.2 Adjusting the flow rate
The carbonation valve has an adjustable flow rate. The optimum setting for the valve
is 1.6 litres per minute. Using a 6mm Allen key or a large flat blade screw driver, you
can adjust the flow on the valve.
1.After product commissioning and CO2 purge, you are now ready to adjust carbona-
tor water flow rate.
2. To adjust the flow rate, rotate the adjustment screw anti-clockwise to increase the
flow and clockwise to decrease the flow, see FIG.3. (Use 1/4 or 1/2 turn increments)
3.To measure theflow rateyou have set,use ameasuring cupor jug andrun thespar-
kling water for 15 seconds. Multiply the amount of water dispensed in that 15 seconds
by 4 to get your flow rate in litres per minute. 1.6 litres per minute is the optimum flow
rate.
Warning - Take care NOT to use excessive force
during adjustment of the carbonation valve.
Rotate to adjust
water flow
FIG.3
Commissioning

Page 16 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
Section 6
Maintenance
6.1 Water Filter Replacement
NOTE: For safe operation, the filter cartridge should be replaced every 6-12
months, or earlier if you notice a persistent reduction in water pressure from the
appliance or an unpleasant taste or odour in the water.
Water Filter Change:
1. Turn off the water and power supply to the unit.
2. Turn the still water lever (blue ringed lever) on, to release any water
pressure in the unit. Once water has stopped running from the tap turn off
the lever.
3. Turn the filter clock wise and gently pull the cartridge down. The cartridge
should release from the filter head. Dispose of the filter cartridge
responsibly. Clean any water that has pooled below the filter head.
4. Fit a new filter by turning filter anticlockwise and gently pushing up. The
filter will click or lock into place.
5. Turn the still water tap on.
6. Turn on the water supply to the unit.Allow 7.5 litres to flow from the
outlet.
7. Turn off the still water lever.
8. Turn on the power supply to the unit.
Warning
Not changing filtration cartridges when required, may cause the water to become
biologically unsafe.
If the Zip ChillTap is switched off for a long period of time (e.g. More than a
weekend), run water through the chilled water outlet for at least 5 minutes before
consumption.
Use only a Zip Filter to match that used with this ChillTap (if fitted). Replacement filter
cartridges can be obtained through plumbing suppliers or directly from Zip.
Replacement instructions come with the filter cartridges.
Before attempting to disconnect or remove the filter cartridge from the housing,
isolate (turn off) the water supply prior to the filter system, and then relieve the
system pressure by operating the chilled water outlet tap until the water ceases to
flow.
1. ROTATE
2. PULL DOWN
1. INSERT
2. ROTATE
REMOVE FILTER INSERT FILTER

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 17 of 20
6.3 Gas Bottle Replacement:
1. Turn off the water and power supply to the chilled sparkling unit.
2. Turn off the regulator on top of the bottle. The regulator has a left hand thread,
to turn off, turn anticlockwise until shut.
3. Remove the CO2 bottle from its mounting and unscrew the bottle from the
regulator. The braided hose may be left connected to the regulator, or, for
convenience, removed and refitted to the regulator and new bottle.
4. Connect the new bottle to the regulator. Be aware that some CO2 may be
discharged from the connection to the regulator when the bottle and the regulator
are assembled together. Any CO2 released will be cold.
5. Ensure the braided hose is correctly fitted to the regulator, with the sealing olive
in place, before turning on the gas.
6. Turn the regulator on
7. Turn the sparkling lever to the on position. Leave it on until all the water has
been purged through the tap. Let the tap run for a further 10 seconds to purge
the CO2 through the tank. Turn off the sparkling lever.
8. Turn on the cold water supply first and then the power supply.
9. Wait 20 seconds and then turn on the sparkling lever and wait for water to
start to come through.
10. Dispense some sparkling water from the tap. Perform a taste test.
Service
There are no user serviceable parts but there are dangerous voltages present
within the unit.All service work must only be carried out by a suitably qualified and
experienced service person.
Before calling for service, check that both the water and electricity supplies are turned
‘ON’ and OK.
Call a licenced electrician, plumber, or Zip for a free call in Australia on 1800-
638-633, for assistance, service, spare parts, or enquiries.
6.2 Air Filter Change:
The Zip ChillTap air filter is conveniently located on the outside of the condenser. The
filter screen is a sliding fit in the plastic housing on the left hand side of the under sink
unit. The screen may be removed for cleaning, by sliding it forward. This needs to be
inspected at least quarterly, cleaned and replaced if damaged.
Note : For best performance the unit should only be operated with a clean air filter
screen, correctly fitted in place. Maintain, at least, a 50mm air gap in front of the
screen at all times. Take care not to allow cloths or other soft materials to accidentally
block the air inlet.
Slide to remove
Filter
Maintenance

Page 18 of 20 804721- CS_ChillTap Sparkling 09.16 v1.00
Symptom Possible Cause Responsibility Solution
No still water
No sparkling water
Poor levels of
carbonation in drinks
Mains water not
connected or turned on
Water pressure regulator
failed
Unit frozen up
No CO2 pressure
Internal fault
Water temperature high
Air in carbonation can
Residue in carbonation
can
Carbonation can is
overfilled
Connect or turn on water supply.
Contact local Zip Service Provider.
Contact local Zip Service Provider.
Check if CO2 regulator valve is open.
Replace empty CO2 gas bottle.
Contact local Zip Service Provider.
See warm drinks symptom below, or allow chilled
system time to recover.
Purge system as described on page 15 “Gas Bottle
Replacement”.
Contact local Zip Service Provider.
Contact local Zip Service Provider..
Prior to any fault finding, please ensure all water connections to the chiller are sound and that the incoming water supply is
turned on.Also ensure that all electrical connections to the chiller are secure and that the chiller has had adequate time to
cool down.
User or Service
Technician
Service
Technician
Service
Technician
User
Service
Technician
User
User
Service
Technician
Service
Technician
Trouble Shooting

804721 - CS_ChillTap Sparkling 09.16 v1.00 Page 19 of 20
In order to help preserve our environment we ask that you dispose of this
product correctly. Please contact your local city council for collection centre
details.
End of Life Disposal
Never use strong, corrosive or abrasive cleaning materials on the Zip ChillTap.
Wipe clean the outer surfaces with a sponge or a soft cloth using a mild soap
and water.
The louvres on the sides of the chiller unit need to be kept free of dust and lint
to permit free flow of air through the vents. They should be checked regularly, at
least monthly, and dusted or vacuumed.
Sanitising the Carbonation unit, may be required when the quality of sparkling
water deteriorates. Please contact your local Zip service provider.
Cleaning
Warm drinks No power
Thermostat faulty or out of
calibration.
Insufficient cooling air flow
through the refrigeration
system
Refrigeration failure
Rated chilled water capacity
has be expended
Restore power to the unit.
Contact local Zip Service Provider.
Contact local Zip Service Provider.
Contact local Zip Service Provider.
Allow unit sufficient time to recover.
Symptom Possible Cause Responsibility Solution
User or Service
Technician
Service
Technician
Service
Technician
Service
Technician
User
Trouble Shooting continued

804721 ChillTap Sparkling 09.16 v1.0
WMKA21821
ATS 5200.105
Contact Details
Head Office
Zip Heaters (Aust) Pty. Ltd.
ABN: 46 000 578 727
67 Allingham Street
Condell Park NSW 2200
Postal: Locked Bag 80
Bankstown 1885 Australia
Website: www.zipwater.com
Facsimile: [phone]
Telephone: [phone]
Sales & Service.
Free Call: 1 800 63 86 33
Customer Care.
Free Call: 1 800 42 43 44
As Zip policy is one of continuous product improvement, changes to specifications may be made
without prior notice. Images in this booklet have been modified and may not be true representations
of the finished goods.
The standard glass is 200 ml (7 floz).
The terms “Zip” and “ChillTap” are registered trade marks of Zip Heaters (Aust) Pty Ltd.
Zip products described in this publication are manufactured under one or more of the following
patents: AU675601, AU637412, AU635979, GB0422305, GB2065848, US4354049, US5103859,
US5099825 and SA2006/08043. Other patents are in force and patent applications are pending.