Zip HydroTap BC User manual

807113 v1.00 12.20 AIO Vented Install Instructions
Connect the water supply
See 4
WHITE marked Braided
hose to mixer tap
All fittings are supplied apart from the isolation valve.
2x male adaptor
1/2” BSP adaptor
T-piece
6
Mains water
Isolation valve
(not supplied)
Connect together
!
Valves and fittings
must be sealed
with PTFE tape
Mains In Mains potable water supply.
USB Connected to the Tap.
Boiling out Red silicone tube from tap. Cut to length.
Chilled out (BC) Blue silicone tube from tap,
(BCS ) Blue JG pipe from tap. Cut to length.
Vent Clear silicone tube from tap. Cut to length.
Sparkling out White JG pipe from tap. Cut to length.
Mixer in Blue marked braided hose from mixer tap.
Mixer out Red marked braided hose from mixer tap.
Command Centre connections
7
8Cleaning and general maintenance
Zip
HydroTap
Installation instructions
Classic / Classic Plus All-in-One Vented Mixer
BC, BCS
Wipe surfaces with a damp cloth and then wipe dry
with a clean, dry cloth. Do not use disinfectant sprays
without wiping dry afterwards.
WMK25927
AS/NZS 3718
Flow restrictor
Visit our website to download the manuals
Australia UK
Zip Water (Aust) Pty Ltd
ABN 46 000 578 727
67 - 77 Allingham Street, Condell Park, NSW 2200
Postal: Locked Bag 80, Bankstown 1885, Australia
([phone] | Free Call (Aust): 1800 947 827
www.zipwater.com
Zip Water UK
Trafalgar House
Rash’s Green, Dereham,
Norfolk NR19 1JG
0345 6 005 005 | [email protected].uk
specify.zipwater.co.uk
Braided hose to
Command Centre
MAINS inlet (supplied
with Command Centre)
1/2” BSP adaptor
Strainer

193mm
234mm
Positioning
Position the tap such that it dispenses into the
sink bowl with clearance for a cup or tea pot.
Ensure that taps are positioned to minimise
the risks of scalding when dispensing
boiling water.
!
1
2
Position Command Centre
and Tap as close together as
possible. See below.
Cut the hole
• Cut a Ø50mm hole in the worktop / sink.
Ø50mm
Familiarise yourself with the tap connections
Fit braided hoses, matching
the hose colours to the tap
BLUE Chilled
tube
RED
Boiling
tube
CLEAR
Vent
tube
USB
Sparkling
models
Mains connections
See 6
Command
Centre
quick guide
4
Familiarise yourself with the tap connections
3
Check the hose, USB,and pipe positions on the base
clamp.
Blue marked
braided hose
White marked
braided hose
Blue silicone
tube
Clear
silicone tube
Red silicone
tube
Red marked
braided hose
USB cable
Mount and secure the tap
Base clamp
O-ring
Fixing nut
5
BCS Comm
InLine
ELECTRONIC
7
Use a tube spanner to secure
the tap in place.
Using these instructions
Please refer to all safety and installation requirements
detailed in the Quick start guide provided with the
HydroTap Command Centre, and HydroTap Command
Centre installation instructions found online, prior to
installation of, or any change to, the complete system.
Before commencing the
installation,download
& read the HydroTap
Command Centre
installation instructions
!
Read the
instructions
WARNING
Tools needed for tap installation
In addition to normal tools, the following (or equivalent
equipment) will be required.
• 50mm diameter sheet metal hole punch for sinks.
• 50mm diameter hole saw for worktops.
• Tube spanner for fixing the tap assembly (supplied).
Be aware of the risks of hazards which could
cause harm when using tools. Assess the
risks before starting the installation.
!
Min - Max pressure, kPA (bar)
Australia UK
HydroTap 170 (1.7) - 700 (7.0) 170 (1.7) - 500 (5.0)
Sparkling
HydroTap 250 (2.5 ) - 700 (7.0) 250 (2.5) - 500 (5.0)
Booster 200 (2.0) - 700 (7.0) 200 (2.0) - 500 (5.0)
Water supply pressure requirements