Zoeller 10-2614 APAK User manual

© Copyright 2020 Zoeller®Co. All rights reserved.
FM2573
1220
Supersedes
1116
PN 1024593 Rev. J
Model TAAB
Notice to Installer: Instructions must remain with installation.
Product information presented
here reects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
TEL: [phone] • 1 (800) 928-PUMP • FAX: [phone]
Visit our website:
zoellerpumps.com
MODEL 10-2614 APAK
®
ALARM SYSTEMS WITH AUXILLIARY CONTACTS
WIRING INSTRUCTIONS
ELECTRICALSHOCKHAZARD-Disconnect all
power sources before servicing. Failure to do so could result
in serious injury or death.
1) Removethethreescrewsfromthebackoftheenclosureasshownin
Fig. A.
2) Remove the back of the enclosure. Note the position of the power
cordinthe enclosure. The cord will need to be located in thesame
manner when the enclosure back is replaced.
3) Determine the location where the auxiliary contact wires will
enter the housing. See Fig. B for recommended location. Before
drilling the hole, loosen the circuit board mounting screw and
remove the circuit board. See Fig. C.
4) At the selected location, drill a hole in the enclosure suitable for
the strain relief that will be used (strain relief not included).
5) Install strain relief and reinstall the circuit board. Connect wires
to the terminal block shown in Fig. C.
6) Markings on the circuit board show positions for Common (C),
Normally Open (NO), and Normally Closed (NC).
7) Position the power cord into place as it was prior to removing the
enclosure back as shown in Fig. C.
8) Reinstall the enclosure back and three screws.
CAUTION
Do not over torque screws. Screw bosses may
become stripped.
9) Note that while testing the installed product, the auxiliary alarm
wired to the auxiliary contacts should activate in an alarm
condition.Theauxiliaryalarmshouldalsoremainin alarmcondition
when the silence button is pushed.
Auxiliary Contacts Specifications
Voltage: 120 VAC
Current: 5 amps max. N/O
3 amps max. N/C
NOTE: This unit includes auxiliary contact option. Due to increased
power consumption, if an alarm condition occurs while on battery
backup power, this option will reduce the life of the battery.
SK2775
Figure A Figure B Figure C
All electrical systems must be installed by a qualified licensed electrician according to the National
Electrical Code and all other applicable codes.

© Copyright 2020 Zoeller®Co. All rights reserved.
ZOELLER
ALARM
ZOELLER
PUMP "ON"
PUMP "OFF"
FIBERGLASS
OR POLYETHYLENE
BASIN
"ON" LEVEL
VARIABLE LEVEL
CONTROL SWITCH
LEVEL
LEVEL
4" OF GRAVEL
ALARM
TRANSFORMER
ZOELLER
DISCONNECTS
NOT SHOWN TO POWER
SUPPLY
UNICHECK
SK367
TYPICAL SIMPLEX SYSTEMS WITH BELL ALARM SYSTEM
WIRING DIAGRAM
(10-0015)
(10-0016)
(10-0028)
DISCONNECT
NOT SHOWN
NOTE: ALARM SYSTEM SHOULD BE ON
A SEPARATE CIRCUIT FROM PUMPS.
SK313
TRANSFORMER
115 TO 8V
OR
230 TO 8V
L1
L2
POWER
UTILITY
BOX
ALARM BELL
8V
TO
CONTROL SWITCH
SEE FM0419 FOR MOUNTING
INSTRUCTIONS.
-OR-
MECHANICAL ALTERNATOR
(10-0075) WITH ALARM
SUPPLY
ZOELLER VARIABLE LEVEL
CONTACTS.
BELL ALARM SYSTEMS
TYPICAL INSTALLATION AND WIRING INSTRUCTIONS
NOTE: Utility box and cordage sold separately. Bell Alarms 10-0015 and 10-0016 are designed to be used with Alarm Pack 10-2614.
Model Voltage dB @ 10’ Bell Transformer Float
10-0015 115V 74 P P
10-0016 230V 74 P P
10-0028 115V 78 P P P
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
[phone] • 1 (800) 928-PUMP • FAX [phone] Visit our website:
zoellerpumps.com
All electrical systems must be installed by a qualified licensed electrician according to the
National Electrical Code and all other applicable codes.
TEST
SILENCE
ALARM
POWERON
ZOELLER
ALARM
ZOELLER
PUMP "ON"
PUMP "OFF"
FIBERGLASS
OR POLYETHYLENE
BASIN
"ON" LEVEL
VARIABLE LEVEL
CONTROL SWITCH
LEVEL
LEVEL
4" OF GRAVEL
BELL ALARM
TRANSFORMER
ZOELLER
DISCONNECTS
NOT SHOWN
TO POWER
SUPPLY
UNICHECK
ALARM PANEL
TO POWER SUPPLY
"DO NOT" PLUG "A-PAK ALARM SYSTEM
INTO THE SAME CIRCUIT AS THE PUMP
AUX. CONTACTS
SK2911