Zte Z6250CC User manual

1
Z6250CC
User Guide

2
LEGAL INFORMATION
Copyright © 2020 ZTE CORPORATION.
All rights reserved.
No part of this publication may be quoted, reproduced,
translated or used in any form or by any means,
electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE
Corporation.
Notice
ZTE Corporation reserves the right to make
modifications on print errors or update specifications in
this guide without prior notice.
We offer self-service for our smart terminal device users.
Please visit the ZTE official website (at
www.ztedevices.com) for more information on self-
service and supported product models. Information on
the website takes precedence.
Disclaimer
ZTE Corporation expressly disclaims any liability for
faults and damages caused by unauthorized
modifications of the software.
Images and screenshots used in this guide may differ
from the actual product. Content in this guide may differ
from the actual product or software.
Trademarks
ZTE and the ZTE logos are trademarks of ZTE
Corporation.
Android™ is a trademark of Google LLC.
The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth SIG, Inc. and any
use of such marks by ZTE Corporation is under license.
microSDXC Logo is a trademark of SD-3C,
LLC.
Other trademarks and trade names are those of their
respective owners.
Version No.: R1.0
Edition Time : May 18, 2020
Manual No.:

3
Getting to Know Your Phone
Front camera
Touch screen
Earpiece Proximity &
light sensor
Volume ke
y
Power key
Charging/USB
Type-C jack
Headset jack
Back cameras
and flash
Speaker
Indicator light
nano-SIM/
microSDXC
card tray
Fingerprint
sensor

4
Setting Up Your Phone
The nano-SIM card can be installed or removed while
the phone is turned on.
WARNING!
To avoid damage to the phone, do not use any other kind
of SIM cards, or any non-standard nano-SIM card cut
from a SIM card. You can get a standard nano-SIM card
from your service provider.
1. Insert the tip of the tray eject tool into the hole on the
card tray.
2. Pull out the card tray and place the nano-SIM card
and the microSDXC card (optional) on the tray, as
shown. Carefully slide the tray back into place.
nano-SIM
card
microSDXC
card

5
Charging the Phone
Your phone’s battery should have enough power for the
phone to turn on, find a signal, and make a few calls. You
should fully charge the battery as soon as possible.
WARNING!
Use only ZTE-approved chargers and USB Type-C
cables. The use of unapproved accessories could
damage your phone or cause the battery to explode.
NOTE:
To achieve fast charging, you can use the original
charger and USB Type-C cable when charging your
phone.
WARNING!
Do not remove the back cover. The battery is not
removable. Removal may cause fire or explosion.
1. Connect the adapter to the charging jack.
2. Connect the charger to a standard AC power outlet.
3. Disconnect the charger when the battery is fully
charged.
NOTE:
If the battery is extremely low, you may be unable to

6
power on the phone even when it is being charged. In
this case, try again after charging the phone for at least
20 minutes. Contact the customer service if you still
cannot power on the phone after prolonged charging.
Powering On/Off Your Phone
Make sure the battery is charged before powering on.
 Press and hold the Power key to turn on your
phone.
 To power off, press and hold the Power key to open
the options menu, and touch >.
NOTE:
If the screen freezes or takes too long to respond, try
pressing and holding the Power key for over 10 seconds
to restart the phone.
Waking Up Your Phone
Your phone automatically goes into sleep mode when it
is not in use for some time. The display is turned off to
save power and the keys are locked to prevent
accidental operations.
You can wake up your phone by turning on the display
and unlocking the keys.
1. Press the Power key to turn the screen on.
2. Swipe up on the screen.
NOTE:
If you have set a fingerprint, an unlock pattern, a PIN or
a password for your phone, you’ll need to use your
fingerprint, draw the pattern, or enter the PIN/password
to unlock your screen.

7
Product Safety Information
Don’t make or receive phone calls while
driving. Never text while driving.
Keep your phone at least 10 mm away from
your body while making calls.
Small parts may cause choking.
Your phone can produce a loud sound.
To prevent possible hearing damage, do not
listen at high volume levels for long periods.
Exercise caution when holding your phone
near your ear while the loudspeaker is in use.
Avoid contact with anything magnetic.
Keep away from pacemakers and other
electronic medical devices.
Turn off when asked to in hospitals and
medical facilities.
Turn off when told to on aircraft and at airports.
Turn off when near explosive materials or
liquids.
Don’t use at gas stations.
Your phone may produce a bright or flashing
light.
Don’t dispose of your phone in fire.
Avoid extreme temperatures.
Avoid contact with liquids. Keep your phone
dry.
Do not attempt to disassemble your phone.

8
Only use approved accessories.
For pluggable equipment, the socket-outlet
shall be installed near the equipment and shall
be easily accessible.
Don’t rely on your phone as a primary device
for emergency communications.
FCC RF Exposure Information (SAR)
This phone is designed and manufactured not to exceed
the emission limits for exposure to radio frequency (RF)
energy set by the Federal Communications Commission
of the United States.
During SAR testing, this device was set to transmit at its
highest certified power level in all tested frequency
bands, and placed in positions that simulate RF
exposure in usage against the head with no separation,
and near the body with the separation of 10 mm.
Although the SAR is determined at the highest certified
power level, the actual SAR level of the device while
operating can be well below the maximum value. This is
because the phone is designed to operate at multiple
power levels so as to use only the power required to
reach the network. In general, the closer you are to a
wireless base station antenna, the lower the power
output.
The exposure standard for wireless devices employing a
unit of measurement is known as the Specific Absorption
Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.
This device is complied with SAR for general
population/uncontrolled exposure limits in ANSI/IEEE
C95.1-1992 and had been tested in accordance with the
measurement methods and procedures specified in
IEEE1528.
The FCC has granted an Equipment Authorization for
this model phone with all reported SAR levels evaluated

9
as in compliance with the FCC RF exposure guidelines.
SAR information on this model phone is on file with the
FCC and can be found under the Display Grant section
of www.fcc.gov/oet/ea/fccid after searching on FCC ID:
SRQ-Z6250CC.
For this device, the highest reported SAR value for
usage against the head is 0.861 W/kg, and for usage
near the body is 0.749 W/kg.
While there may be differences between the SAR levels
of various phones and at various positions, they all meet
the government requirements.
SAR compliance for body-worn operation is based on a
separation distance of 10 mm between the unit and the
human body. Carry this device at least 10 mm away from
your body to ensure RF exposure level compliant or
lower to the reported level. To support body-worn
operation, choose the belt clips or holsters, which do not
contain metallic components, to maintain a separation of
10 mm between this device and your body.
RF exposure compliance with any body-worn accessory,
which contains metal, was not tested and certified, and
using such body-worn accessory should be avoided.
FCC Regulations
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful

10
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
CAUTION:
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
Hearing aid compatibility (HAC)
regulations for mobile phones
In 2003, the FCC adopted rules to make digital wireless
telephones compatible with hearing aids and cochlear
implants. Although analog wireless phones do not
usually cause interference with hearing aids or cochlear
implants, digital wireless phones sometimes do because
of electromagnetic energy emitted by the phone's
antenna, backlight, or other components. Your phone is
compliant with FCC HAC regulations (ANSI C63.19-
2011). While some wireless phones are used near some
hearing devices (hearing aids and cochlear implants),
users may detect a buzzing, humming, or whining noise.

11
Some hearing devices are more immune than others to
this interference noise and phones also vary in the
amount of interference they generate. The wireless
telephone industry has developed a rating system for
wireless phones to assist hearing device users in finding
phones that may be compatible with their hearing
devices. Not all phones have been rated. Phones that
are rated have the rating on their box or a label located
on the box. The ratings are not guarantees. Results will
vary depending on the user's hearing device and hearing
loss. If your hearing device happens to be vulnerable to
interference, you may not be able to use a rated phone
successfully. Trying out the phone with your hearing
device is the best way to evaluate it for your personal
needs.
This phone has been tested and rated for use with
hearing aids for some of the wireless technologies that it
uses. However, there may be some newer wireless
technologies used in this phone that have not been
tested yet for use with hearing aids. It is important to try
the different features of this phone thoroughly and in
different locations, using your hearing aid or cochlear
implant, to determine if you hear any interfering noise.
Consult your service provider or the manufacturer of this
phone for information on hearing aid compatibility. If you
have questions about return or exchange policies,
consult your service provider or phone retailer.
M-Ratings: Phones rated M3 or M4 meet FCC
requirements and are likely to generate less interference
to hearing devices than phones that are not labeled. M4
is the better/higher of the two ratings.
T-Ratings: Phones rated T3 or T4 meet FCC
requirements and are likely to be more usable with a
hearing device’s telecoil (“T Switch” or “Telephone
Switch”) than unrated phones. T4 is the better/higher of
the two ratings. (Note that not all hearing devices have
telecoils in them.)

12
Your phone meets the M3/T3 level rating.
Hearing devices may also be rated. Your hearing device
manufacturer or hearing health professional may help
you find this rating. For more information about FCC
Hearing Aid Compatibility, please go to
http://www.fcc.gov/cgb/dro.