ZUMEX Speed Up Citric Active User manual

Zumex Group S.A. Tel. [phone]. [e-mail]. Zumex Service Tel: [phone]. www.zumex.com
This cleaning protocol* guarantees an efficient, hygienic cleaning process, free from
bacteria, even when the equipment is very dirty.
By means of this process, you will also contribute to the proper preventive maintenance
of your Speed Up.
Below are the steps to follow to fulfil the protocol with success.
CLEANING PROTOCOL
① Tools required for effective cleaning:
· Zumex Citric ActiveTM detergent
· Disinfectant: Hydroalcoholic at a concentration of 0.91g/ml
· Clean or new sponge (of a material that does not scratch the machine surfaces)
· Clean disposable paper
· Wash point
· Brush supplied (for the cleaning points which require it)
NOTE: The brush must be cleaned and sanitised by following the instructions below.
*Speed Up (v.00) cleaning instruction validation report
performed by an independent laboratory with report number
IFSC243 / 19Rev3.
② Steps required for effective cleaning:
In the juice circulation zone, follow the specific steps to guarantee maximum hygiene::
1. Apply Zumex Citric ActiveTM to remove wax and pulp. Leave to act 30 seconds and remove the dirt with a sponge.
2. Rinse with water.
3. Apply a hydroalcoholic disinfectant with a concentration of 0.91g/ml and leave to rest for 1 minutes.
4. Rinse with water.
5. Final drying of each of the parts and recesses.

Zumex Group S.A. Tel. [phone]. [e-mail]. Zumex Service Tel: [phone]. www.zumex.com
Disassembly instructions
Take off the feeder basket.
Press the side tabs to remove the bin.
Take off the automatic PulpOut System, by
lifting the assembly with the part closest to
you.
Pull off the peel ejectors.
Remove the waste trolleys from the base
to empty them.
Take off the feeder plate by unscrewing the
central knob.
Remove the blade by pressing on the centre
and pulling the handle towards you.
Caution! Put the protector on the cutting zone.
Remove the Speed Up Tap by easily un-
screwing it.
Unscrew the securing knobs of the pressing
units. Take off the pressing units in pairs.
Clean the inside of the podium, following
the steps shown and removing all the par-
ticles which have adhered.
Turn the knobs and take off the front cover
as well as the side outputs.
Assemble the blade protector.
Remove the stainless-steel peel guides.
Clean the front zone of the machine, fo-
llowing the steps shown and removing all
the particles which have adhered.
Once you have dismounted all the parts,
proceed to the deep cleaning, following the
steps described..
The cleaning process will be explained in details for each one of the machine’s components below.
Caution! For a correct cleaning process, please follow the instructions
below. Before getting started, make sure that the machine is nplugged
from mains power.
1
7
4
10
13
2
8
5
11
14
3
9
6
12
15

Tap Up
Unscrew the top part of the tap by turning
the matte ring, and follow the cleaning
steps indicated above.
Rinse with water, apply the disinfectant,
rinse again and to finish, dry both the
outside and the inside of the tap with paper
(roll the paper on the pin to aid insertion of
the paper into the holes).
Dose the degreaser by inserting the spray
nozzle into the three orifices and applying
the product. Scrub the inside through
the holes with the aid of the small brush
supplied.
1 32
Zumex Group S.A. Tel. [phone]. [e-mail]. Zumex Service Tel: [phone]. www.zumex.com
Instructions for cleaning the components
All the parts, with the exception of the cover and the tap,
can be put in a dishwasher to clean them.
The juicing zone and its removable components must be
cleaned using Citric Active*. Leave to act for one minute
and then proceed to remove the remains of dirt with a
moist sponge.
Do not use scourers which may scratch the surfaces.
Sanitise with a hydroalcoholic disinfectant** after the
first rinse, and leave it to rest for 1 minute.
Rinse with plenty of water after sterilising, in order to
remove any remaining disinfectant.
Dry the parts completely.
Warnings and steps for cleaning and sanitation
It is necessary to clean all parts that come into contact with the juice each day.
!
Blade, sub-filter, bin, peel guides, feed plate, front cover, and tap
Daily cleaning
Follow the cleaning process indicated, for all
the parts: blade, sub-filter, tank, peel chu-
tes, etc.
Clean the cover, following the steps shown
and removing all the particles which have
adhered.
Unscrew the top part of the tap by turning
the matte ring, and follow the cleaning
steps indicated above.
Wash the feeder plate with Citric Active
and a soft sponge, removing all the parti-
cles which have stuck to it.
* Detergent for food use specific to Zumex Juicers. ** Disinfectant for food use recommended.
1 2 3
4

Zumex Group S.A. Tel. [phone]. [e-mail]. Zumex Service Tel: [phone]. www.zumex.com
Instructions for cleaning the components
Automatic PulpOut System
Remove the black upper lid by pushing
upwards on the tabs sticking out.
Clean the conveyor belt and the rest of the
components of the Pulp Out with the clea-
ning steps indicated.
Rest the PulpOut system on a flat surface
and disassemble the side cover, holding it
from above to remove the ends of the gui-
des.
Remove the sweeping belt together with
the other roller and remove both parts.
Turn the assembly around and place your
fingers on the sweeping belt by pushing it
outwards to release it.
All the parts can also be washed in a dish-
washer.
Squeezing system
Remove the pressing units. Clean all the parts following the steps
shown. All the parts can also be washed in
a dish- washer.
21
2
5
1
4
3
6

Zumex Group S.A. Tel. [phone]. [e-mail]. Zumex Service Tel: [phone]. www.zumex.com
Recommended cleaning instructions
Cover, Juicing system and PulpOut system
Midday cleaning (recommended for machines under intensive use)
Turn the knobs and take off the front cover
as well as the side outputs.
Assemble the blade protector.
Clean the front zone of the machine, fo-
llowing the steps shown and removing all
the particles which have adhered.
Take off the automatic PulpOut System, by
lifting the assembly with the part closest to
you.
Pull off the peel ejectors.
Remove the blade by pressing on the centre
and pulling the handle towards you.
Caution! Put the protector on the cutting zone.
Unscrew the securing knobs of the pressing
units. Take off the pressing units in pairs.
Clean all the parts
with the steps
described.
Replacing parts.
For quick cleaning in the middle
of the day, we recommend
having a kit with spare parts.
This Kit is made up of: a cover,
juicing system and PulpOut
system.
1
4
7
2
5
3
6