ZURN AquaSense Z6933 User manual

LIMITED WARRANTY
All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the
date of purchase. Decorative nishes warranted for one year. We will replace at no costs goods that prove defective provided we are
notied in writing of such defect and the goods are returned to us prepaid at Sanford, NC, with evidence that they have been properly
maintained and used in accordance with instructions. We shall not be responsible for any labor charges or any loss, injury or damages
whatsoever, including incidental or consequential damages. The sole and exclusive remedy shall be limited to the replacement of the
defective goods. Before installation and use, the purchaser shall determine the suitability of the product for his intended use and the
purchaser assumes all risk and liability whatever in connection therewith. Where permitted by law, the implied warranty of merchantability
is expressly excluded. If the products sold hereunder are “consumer products,” the implied warranty of merchantability is limited to a
period of three years and shall be limited solely to the replacement of the defective goods. All weights stated in our catalogs and lists
are approximate and are not guaranteed.
Sensor-Operated Lavatory Faucet
NOTICE: READ ENTIRE MANUAL PRIOR TO INSTALLING PRODUCT.
AquaSense®
Battery Powered Sensor Faucets
Installation, Operation, Maintenance
and Parts Manual
Patented and Patents Pending
WARNING: Cancer and Reproducve Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproducvo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et eets néfastes sur la reproducon - www.P65Warnings.ca.gov
Z6933

This Page Intentionally Left Blank

FV763 Rev. A 01/25/21
Page 1
Control
Box
Batteries
Spout Assembly
Rubber
Horseshoe
Brass
Horseshoe
Screws
Anchors
Fixing Bolts
with nuts
Flexible
Hose
Required Tools
Z6933 AquaSense®Package Contents
Smooth Jawed
Wrench
Phillips Head
Screwdriver
Flat Head
Screwdriver

FV763 Rev. A 01/25/21
Page 2
Overview:
Designed for modern commercial restrooms, the AquaSense Z6933 sensor faucet delivers a superior user experience
in both form and function. This faucet maintains a sleek and simple design that is easy to install and a user-friendly
handwashing solution.
This faucet has been designed and manufactured to comply with Section 1417 of the Safe Drinking Water Act
(SDWA) which mandates the weighted average lead content of no more than 0.25% of the wetted surface.
NOTE: The information in this manual is subject to change at any time without notice. Installations may be performed
at di󰀨erent times of construction by di󰀨erent individuals. For this reason, these instructions should be left on-site
with the facility or maintenance manager.
Specications:
Voltage: 6 VDC Series [4 “AA” (Alkaline)]
Sensor Range: 10”-2” (25-31cm)
Operating Water Pressure: 7.25-101 psi (0.05-0.7MPa)
Operational Water Temperature: 33°F to 131°F (1°C to 55°C)
Aerator: Spray, 0.5 GPM (Standard)
Diameter of Inlet: G1/2”
Important Safety Information:
• Installer is responsible for ensuring the product is installed and conforms to all plumbing codes and ordinances.
• Do not convert or modify this Zurn product yourself. All warranties will be voided.
• Water supply lines must be sized according to building designer in order to provide adequate water supply
for each xture.
• Flush all water lines prior to making connections.
Be sure the water supply is turned on and the sink/lavatory/basin is clear from any objects upon making the sensor to electronics
connection initiating the self-calibration feature. The sink must be clear of any and all objects and water supply is turned on in order
to calibrate appropriately (calibration time approx 30-60sec) (the system will perform both a wet & dry calibration).
Prior to Installation:
Before installing your Zurn®AquaSense®Faucet: the items listed below should already be installed on site.
• Lavatory/sink
• Drain Line
• Hot and cold water supply line or pre-tempered water supply line.
• Installer/Servicer should not use pipe dope or teon/thread sealant anywhere on this product, most notably threads
and connection points.
• Care shall be taken when installing this product to prevent marring of any exposed or decorative surfaces.

FV763 Rev. A 01/25/21
Page 3
NOTE: Always ush pipework before installation.
The installation place which you choose and design should be sunless and lightless.
Installation Overview
Body
Sensor Window
Stop Valve
Basin
Control Box
Aerator
Sensor Window
Spout
Fixing Bolt
Control Box
Connector
Rubber
Horseshoe
Basin
Brass
Horseshoe
Flexible Hose
Fixing Nut

FV763 Rev. A 01/25/21
Page 4
1. Screw exible hose into faucet body. 2. Screw xing bolts into facuet body with
a at-head screwdriver.
5. Open control box with phillips head
screwdriver.
7. Fix control box close to faucet (ensure
flexible hose will connect), using
anchors and screws provided.
10. Connect control box (in) to water
supply.
8. Connect sensor fable to control box
socket and screw plastic nut tightly.
9. Connect exible hose from faucet to
control box (out).
3. Feed hose and faucet through deck
opening.
4. Slide horseshoes (rubber, then brass)
up through xing bolts and fasten to
the deck with xing nuts.
Installation Instructions
6. Install 4 AA batteries.

FV763 Rev. A 01/25/21
Page 5
Whilst modern plating techniques are used in manufacture of this product, the surface will be a󰀨ected if cleaned incorrectly.
Surfaces should be maintained using a lean damp cloth, no abrasive agents or materials should be used or come into contact with the
surface nish, or this will invalidate your warranty
For further assistance with troubleshooting visit http://www.zurn.com
Problem Possible Cause Corrective Action
No water out The baery is exhausted
(DC item)
Change the baery
Water supply cut o Check water supply
Dirt in the lter Clean the lter
Water pressure is too low Raise the pressure
Water will not turn o Dirt on the sensor window Clear the dirt
Too lile water ow Water supply is turned too small Adjust water supply
The lter is too dirty Clean the lter
Water pressure is too low Raise the pressure
Too much water ow Water supply is turned too high Adjust supply
Water pressure is too high Adjust pressure
Short cycles of baery Incorrect baeries Change to 4 AA alkaline baery
The indicator light
is not on
The light is broken Change the light or circuitry board
The circuitry board is wet or
signal line is wet
Dry out
The baery is exhausted Change the baery
Poor connecon of baery Check the baery connecon
Trouble-Shooting
Care & Maintenance

US 1.855.ONE.ZURN CANADA 1.905.405.8272 ZURN.COM
ZURN INDUSTRIES, LLC 511 W. Freshwater Way, Milwaukee, WI U.S.A. 53204 · Ph. 1-855-ONE-ZURN, Fax [phone]
In Canada: ZURN INDUSTRIES LIMITED 7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, Ph. 905-405-8272, Fax [phone]
Rev. A Date:
01/25/21 C.N. No. 143158 Prod. | Dwg. No. FV763